| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch correct a bug in the delay of pktgen.
It makes sure the inter-packet interval is accurate.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gen_kill_estimator() / gen_new_estimator() is not always called with
RTNL held.
net/netfilter/xt_RATEEST.c is one user of these API that do not hold
RTNL, so random corruptions can occur between "tc" and "iptables".
Add a new fine grained lock instead of trying to use RTNL in netfilter.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 1f8438a85366 (icmp: Account for ICMP out errors), I did a typo
on IPV6 side, using ICMP6_MIB_OUTMSGS instead of ICMP6_MIB_OUTERRORS
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The extra ! character means that these conditions are always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BugLink: http://bugs.launchpad.net/bugs/591416
There are a number of network drivers (bridge, bonding, etc) that are not yet
receive multi-queue enabled and use alloc_netdev(), so don't print a
num_rx_queues imbalance warning in that case.
Also, only print the warning once for those drivers that _are_ multi-queue
enabled.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.
This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This makes "iw wlan0 dump survey" work again with
mac80211-based drivers that support it, e.g. ath5k.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ipmr_rules_exit() and ip6mr_rules_exit() free a list of items, but
forget to properly remove these items from list. List head is not
changed and still points to freed memory.
This can trigger a fault later when icmpv6_sk_exit() is called.
Fix is to either reinit list, or use list_del() to properly remove items
from list before freeing them.
bugzilla report : https://bugzilla.kernel.org/show_bug.cgi?id=16120
Introduced by commit d1db275dd3f6e4 (ipv6: ip6mr: support multiple
tables) and commit f0ad0860d01e (ipv4: ipmr: support multiple tables)
Reported-by: Alex Zhavnerchik <alex.vizor@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With mtu=9000, mld_newpack() use order-2 GFP_ATOMIC allocations, that
are very unreliable, on machines where PAGE_SIZE=4K
Limit allocated skbs to be at most one page. (order-0 allocations)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Its better to make a route lookup in appropriate namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I believe a moderate SYN flood attack can corrupt RFS flow table
(rps_sock_flow_table), making RPS/RFS much less effective.
Even in a normal situation, server handling short lived sessions suffer
from bad steering for the first data packet of a session, if another SYN
packet is received for another session.
We do following action in tcp_v4_rcv() :
sock_rps_save_rxhash(sk, skb->rxhash);
We should _not_ do this if sk is a LISTEN socket, as about each
packet received on a LISTEN socket has a different rxhash than
previous one.
-> RPS_NO_CPU markers are spread all over rps_sock_flow_table.
Also, it makes sense to protect sk->rxhash field changes with socket
lock (We currently can change it even if user thread owns the lock
and might use rxhash)
This patch moves sock_rps_save_rxhash() to a sock locked section,
and only for non LISTEN sockets.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syncookies default to on since
e994b7c901ded7200b525a707c6da71f2cf6d4bb
(tcp: Don't make syn cookies initial setting depend on CONFIG_SYSCTL).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xfrm triggers a warning if dst_pop() drops a refcount
on a noref dst. This patch changes dst_pop() to
skb_dst_pop(). skb_dst_pop() drops the refcnt only
on a refcounted dst. Also we don't clone the child
dst_entry, so it is not refcounted and we can use
skb_dst_set_noref() in xfrm_output_one().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Processing an association response could take a bit
of time while we set up the hardware etc. During that
time, the AP might already send a blockack request.
If this happens very quickly on a fairly slow machine,
we can end up processing the blockack request before
the association processing has finished. Since the
blockack processing cannot sleep right now, we also
cannot make it wait in the driver.
As a result, sometimes on slow machines the iwlagn
driver gets totally confused, and no traffic can pass
when the aggregation setup was done before the assoc
setup completed.
I'm working on a proper fix for this, which involves
queuing all blockack category action frames from a
work struct, and also allowing the ampdu_action driver
callback to sleep, which will generally clean up the
code and make things easier.
However, this is a very involved and complex change.
To fix the problem at hand in a way that can also be
backported to stable, I've come up with this patch.
Here, I simply process all aggregation action frames
from the managed interface skb queue, which means
their processing will be serialized with processing
the association response, thereby fixing the problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
access skb->data safely
we should use skb_header_pointer() and skb_store_bits() to access skb->data to
handle small or non-linear skbs.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/sched/act_pedit.c | 24 ++++++++++++++----------
1 file changed, 14 insertions(+), 10 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use skb_header_pointer() to dereference data safely
the original skb->data dereference isn't safe, as there isn't any skb->len or
skb_is_nonlinear() check. skb_header_pointer() is used instead in this patch.
And when the skb isn't long enough, we terminate the function u32_classify()
immediately with -1.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For large values of rtt, 2^rho operation may overflow u32. Clamp down the increment to 2^16.
Signed-off-by: Daniele Lacamera <root@danielinux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix the wrong checksum when addr isn't in old_addr/mask
For TCP and UDP packets, when addr isn't in old_addr/mask we don't do SNAT or
DNAT, and we should not update layer 4 checksum.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/sched/act_nat.c | 4 ++++
1 file changed, 4 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a skb is received on an inactive bond that does not meet
the special cases checked for by skb_bond_should_drop it should
only be delivered to exact matches as the comment in
netif_receive_skb() says.
However because null_or_bond could also be null this is not
always true. This patch renames null_or_bond to orig_or_bond
and initializes it to orig_dev. This keeps the intent of
null_or_bond to pass frames received on VLAN interfaces stacked
on bonding interfaces without invalidating the statement for
null_or_orig.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vlan device should not copy the slave or master flags from
the real device. It is not in the bond until added nor is it
a master.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets going through __xfrm_route_forward() have a not refcounted dst
entry, since we enabled a noref forwarding path.
xfrm_lookup() might incorrectly release this dst entry.
It's a bit late to make invasive changes in xfrm_lookup(), so lets force
a refcount in this path.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dialog token allocator has apparently been broken
since b83f4e15 ("mac80211: fix deadlock in sta->lock")
because it got moved out under the spinlock. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Daniel reported that the paged RX changes had
broken blockack request frame processing due
to using data that wasn't really part of the
skb data.
Fix this using skb_copy_bits() for the needed
data. As a side effect, this adds a check on
processing too short frames, which previously
this code could do.
Reported-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit: c720c7e8383aff1cb219bddf474ed89d850336e3 missed these.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
|
|
Correct sk_forward_alloc handling for error_queue would need to use a
backlog of frames that softirq handler could not deliver because socket
is owned by user thread. Or extend backlog processing to be able to
process normal and error packets.
Another possibility is to not use mem charge for error queue, this is
what I implemented in this patch.
Note: this reverts commit 29030374
(net: fix sk_forward_alloc corruptions), since we dont need to lock
socket anymore.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit f3c5c1bfd4 (netfilter: xtables: make ip_tables reentrant)
introduced a performance regression, because stackptr array is shared by
all cpus, adding cache line ping pongs. (16 cpus share a 64 bytes cache
line)
Fix this using alloc_percpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-By: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
In xt_register_table, xt_jumpstack_alloc is called first, later
xt_replace_table is used. But in xt_replace_table, xt_jumpstack_alloc
will be used again. Then the memory allocated by previous xt_jumpstack_alloc
will be leaked. We can simply remove the previous xt_jumpstack_alloc because
there aren't any users of newinfo between xt_jumpstack_alloc and
xt_replace_table.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Acked-By: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
|
|
As David found out, sock_queue_err_skb() should be called with socket
lock hold, or we risk sk_forward_alloc corruption, since we use non
atomic operations to update this field.
This patch adds bh_lock_sock()/bh_unlock_sock() pair to three spots.
(BH already disabled)
1) skb_tstamp_tx()
2) Before calling ip_icmp_error(), in __udp4_lib_err()
3) Before calling ipv6_icmp_error(), in __udp6_lib_err()
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The accept()'d socket need to be unhashed while the (listen()'ing)
socket lock is held. This fixes a race condition that could lead to an
OOPS.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was an spin_unlock missing on the error path. The spin_lock was
tucked in with the declarations so it was hard to spot. I added a new
line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Brændeland <sjurbren@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a mutex_unlock missing on the error path. In each case, whenever the
label out is reached from elsewhere in the function, mutex is not locked.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* mutex_lock(E1);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* mutex_unlock(E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Zach Brown <zach.brown@oracle.com>
Acked-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f4f914b5 (net: ipv6 bind to device issue) caused
a regression with Mobile IPv6 when it changed the meaning
of fl->oif to become a strict requirement of the route
lookup. Instead, only force strict mode when
sk->sk_bound_dev_if is set on the calling socket, getting
the intended behavior and fixing the regression.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
sparse correctly complains that
__ieee80211_get_channel_mode is not static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
netlink: bug fix: wrong size was calculated for vfinfo list blob
netlink: bug fix: don't overrun skbs on vf_port dump
xt_tee: use skb_dst_drop()
netdev/fec: fix ifconfig eth0 down hang issue
cnic: Fix context memory init. on 5709.
drivers/net: Eliminate a NULL pointer dereference
drivers/net/hamradio: Eliminate a NULL pointer dereference
be2net: Patch removes redundant while statement in loop.
ipv6: Add GSO support on forwarding path
net: fix __neigh_event_send()
vhost: fix the memory leak which will happen when memory_access_ok fails
vhost-net: fix to check the return value of copy_to/from_user() correctly
vhost: fix to check the return value of copy_to/from_user() correctly
vhost: Fix host panic if ioctl called with wrong index
net: fix lock_sock_bh/unlock_sock_bh
net/iucv: Add missing spin_unlock
net: ll_temac: fix checksum offload logic
net: ll_temac: fix interrupt bug when interrupt 0 is used
sctp: dubious bitfields in sctp_transport
ipmr: off by one in __ipmr_fill_mroute()
...
|
|
The wrong size was being calculated for vfinfo. In one case, it was over-
calculating using nlmsg_total_size on attrs, in another case, it was
under-calculating by assuming ifla_vf_* structs are packed together, but
each struct is it's own attr w/ hdr (and padding).
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Noticed by Patrick McHardy: was continuing to fill skb after a
nla_put_failure, ignoring the size calculated by upper layer. Now,
return -EMSGSIZE on any overruns, but also allow netdev to
fail ndo_get_vf_port with error other than -EMSGSIZE, thus unwinding
nest.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 7fee226a (net: add a noref bit on skb dst), its wrong to
use : dst_release(skb_dst(skb)), since we could decrement a refcount
while skb dst was not refcounted.
We should use skb_dst_drop(skb) instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we disallow GSO packets on the IPv6 forward path.
This patch fixes this.
Note that I discovered that our existing GSO MTU checks (e.g.,
IPv4 forwarding) are buggy in that they skip the check altogether,
when they really should be checking gso_size + header instead.
I have also been lazy here in that I haven't bothered to segment
the GSO packet by hand before generating an ICMP message. Someone
should add that to be 100% correct.
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
