| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is still some confusion and disagreement over what this interface should
actually do. So it is best that we disable it in 2.6.23 until we get that
fully sorted out.
(sys_timerfd() was present in 2.6.22 but it was apparently broken, so here we
assume that nobody is using it yet).
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Davide Libenzi <davidel@xmailserver.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 831441862956fffa17b9801db37e6ea1650b0f69 (Freezer: make kernel
threads nonfreezable by default) breaks freezing when attempting to resume
from an initrd, because the init (which is freezeable) spins while waiting
for another thread to run /linuxrc, but doesn't check whether it has been
told to enter the refrigerator. The original patch replaced a call to
try_to_freeze() with a call to yield(). I believe a simple reversion is
wrong because if !CONFIG_PM_SLEEP, try_to_freeze() is a noop. It should
still yield.
Signed-off-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Alexey Dobriyan reports that maxcpus=1 is still broken in 2.6.23-rc4:
if CONFIG_HOTPLUG_CPU is not set, x86_64 bootup oopses in show_stat() -
for_each_possible_cpu accesses a per-cpu area which was never set up.
Alexey identified commit 61ec7567db103d537329b0db9a887db570431ff4
(ACPI: boot correctly with "nosmp" or "maxcpus=0") as the origin;
but it's not really to blame, just exposes a bug in 2.6.23-rc1's commit
8b3b295502444340dd0701855ac422fbf32e161d (Especially when !CONFIG_HOTPLUG_CPU,
avoid needlessy allocating resources for CPUs that can never become available).
rc1's test for max_cpus < 2 in start_kernel() wasn't working because
max_cpus was still NR_CPUS at that point: until rc4 moved the maxcpus
parsing earlier. Now it sets cpu_possible_map to 1 before allocating
all possible per-cpu areas; then smp_init() expands cpu_possible_map
to cpu_present_map (0xf in my case) later on.
rc1's commit has good intentions, but expects cpu_present_map to be
limited by maxcpus, which is only the case on i386. cpus_and(possible,
possible,present) might be good, but needs an audit of cpu_present_map
uses - there may well be assumptions that any cpu present is possible.
So stay safe for now and just revert those #ifndef CONFIG_HOTPLUG_CPU
optimizations in rc1's commit.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 61ec7567db103d537329b0db9a887db570431ff4 ('ACPI: boot correctly
with "nosmp" or "maxcpus=0"') broke 'maxcpus=' handling on x86[-64].
maxcpus=N is now having no effect on x86_64, and freezing bootup on i386
(because of inconsistency with the separate maxcpus parsing down in
arch/i386, I guess). That's because early_param parsing is a little
different from __setup parsing, and needs the "=" omitted: then it seems
to work as the original commit intended (no mention of IO-APIC in
/proc/interrupts when maxcpus=0).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In MPS mode, "nosmp" and "maxcpus=0" boot a UP kernel with IOAPIC disabled.
However, in ACPI mode, these parameters didn't completely disable
the IO APIC initialization code and boot failed.
init/main.c:
Disable the IO_APIC if "nosmp" or "maxcpus=0"
undefine disable_ioapic_setup() when it doesn't apply.
i386:
delete ioapic_setup(), it was a duplicate of parse_noapic()
delete undefinition of disable_ioapic_setup()
x86_64:
rename disable_ioapic_setup() to parse_noapic() to match i386
define disable_ioapic_setup() in header to match i386
http://bugzilla.kernel.org/show_bug.cgi?id=1641
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove the top level menu "Code maturity level options", and moves its
options into menu "General setup".
This makes Kconfig less cluttered and easier to setup.
Signed-off-by: Al Boldi <a1426z@gawab.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There doesn't seem to be a good reason for ANON_INODES being
an user visible option.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
sh: Fix fs.h removal from mm.h regressions.
sh: fix get_wchan() for SH kernels without framepointers
sh: arch/sh/boot - fix shell usage
rtc: rtc-sh: Correct sh_rtc_set_time() for some SH-3 parts.
sh: remove support for sh7300 and solution engine 7300
sh: Add sh to the CC_OPTIMIZE_FOR_SIZE dependencies.
sh: Kill off virt_to_bus()/bus_to_virt().
sh: sh-sci - fix SH7708 support
sh: Restrict DSP support to specific CPUs.
sh: Silence sq compile warning on sh4 nommu.
sh: Kill the rest of the SE73180 cruft.
sh: remove support for sh73180 and solution engine 73180
sh: remove old broken pint code
sh: Reclaim beginning of P3 space for vmalloc area.
sh: Fix Dreamcast DMA issues.
sh: Add kmap_coherent()/kunmap_coherent() interface for SH-4.
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Presently we only use this with CONFIG_EXPERIMENTAL, but it is
something that can be supported commonly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are some reports that 2.6.22 has SLUB as the default. Not
true!
This will make SLUB the default for 2.6.23.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Especially when !CONFIG_HOTPLUG_CPU, avoid needlessy allocating resources for
CPUs that can never become available.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's useful sometimes to disable the softlockup checker at boottime.
Especially if it triggers during a distro install.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Basically, it will allow a process to unshare its user_struct table,
resetting at the same time its own user_struct and all the associated
accounting.
A new root user (uid == 0) is added to the user namespace upon creation.
Such root users have full privileges and it seems that theses privileges
should be controlled through some means (process capabilities ?)
The unshare is not included in this patch.
Changes since [try #4]:
- Updated get_user_ns and put_user_ns to accept NULL, and
get_user_ns to return the namespace.
Changes since [try #3]:
- moved struct user_namespace to files user_namespace.{c,h}
Changes since [try #2]:
- removed struct user_namespace* argument from find_user()
Changes since [try #1]:
- removed struct user_namespace* argument from find_user()
- added a root_user per user namespace
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Andrew Morgan <agm@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
CONFIG_UTS_NS and CONFIG_IPC_NS have very little value as they only
deactivate the unshare of the uts and ipc namespaces and do not improve
performance.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Acked-by: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some buses (e.g. USB and MMC) do their scanning of devices in the
background, causing a race between them and prepare_namespace(). In order
to be able to use these buses without an initrd, we now wait for the device
specified in root= to actually show up.
If the device never shows up than we will hang in an infinite loop. In
order to not mess with setups that reboot on panic, the feature must be
turned on via the command line option "rootwait".
[bunk@stusta.de: root_wait can become static]
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change menuconfig objects from "menu, config" into "menuconfig" so that the
user can disable the whole feature without entering its menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently slob is disabled if we're using sparsemem, due to an earlier
patch from Goto-san. Slob and static sparsemem work without any trouble as
it is, and the only hiccup is a missing slab_is_available() in the case of
sparsemem extreme. With this, we're rid of the last set of restrictions
for slob usage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
"menu, endmenu" that did not get cleaned up in the block patch
[ http://lkml.org/lkml/2007/4/10/251 ]
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
add the init_idle_bootup_task() callback to the bootup thread,
unused at the moment. (CFS will use it to switch the scheduling
class of the boot thread to the idle class)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Kill a special case in modpost by introducing the
__init_refok marker.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
No arch sets ARCH_USES_SLAB_PAGE_STRUCT anymore.
Remove the experimental dependency as well since we want to have it as
a real alternative to SLAB.
It all comes down to killing a single line from init/Kconfig.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The SLOB allocator should implement SLAB_DESTROY_BY_RCU correctly, because
even on UP, RCU freeing semantics are not equivalent to simply freeing
immediately. This also allows SLOB to be used on SMP.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a very simple and light file descriptor, that can be used as event
wait/dispatch by userspace (both wait and dispatch) and by the kernel
(dispatch only). It can be used instead of pipe(2) in all cases where those
would simply be used to signal events. Their kernel overhead is much lower
than pipes, and they do not consume two fds. When used in the kernel, it can
offer an fd-bridge to enable, for example, functionalities like KAIO or
syslets/threadlets to signal to an fd the completion of certain operations.
But more in general, an eventfd can be used by the kernel to signal readiness,
in a POSIX poll/select way, of interfaces that would otherwise be incompatible
with it. The API is:
int eventfd(unsigned int count);
The eventfd API accepts an initial "count" parameter, and returns an eventfd
fd. It supports poll(2) (POLLIN, POLLOUT, POLLERR), read(2) and write(2).
The POLLIN flag is raised when the internal counter is greater than zero.
The POLLOUT flag is raised when at least a value of "1" can be written to the
internal counter.
The POLLERR flag is raised when an overflow in the counter value is detected.
The write(2) operation can never overflow the counter, since it blocks (unless
O_NONBLOCK is set, in which case -EAGAIN is returned).
But the eventfd_signal() function can do it, since it's supposed to not sleep
during its operation.
The read(2) function reads the __u64 counter value, and reset the internal
value to zero. If the value read is equal to (__u64) -1, an overflow happened
on the internal counter (due to 2^64 eventfd_signal() posts that has never
been retired - unlickely, but possible).
The write(2) call writes an __u64 count value, and adds it to the current
counter. The eventfd fd supports O_NONBLOCK also.
On the kernel side, we have:
struct file *eventfd_fget(int fd);
int eventfd_signal(struct file *file, unsigned int n);
The eventfd_fget() should be called to get a struct file* from an eventfd fd
(this is an fget() + check of f_op being an eventfd fops pointer).
The kernel can then call eventfd_signal() every time it wants to post an event
to userspace. The eventfd_signal() function can be called from any context.
An eventfd() simple test and bench is available here:
http://www.xmailserver.org/eventfd-bench.c
This is the eventfd-based version of pipetest-4 (pipe(2) based):
http://www.xmailserver.org/pipetest-4.c
Not that performance matters much in the eventfd case, but eventfd-bench
shows almost as double as performance than pipetest-4.
[akpm@linux-foundation.org: fix i386 build]
[akpm@linux-foundation.org: add sys_eventfd to sys_ni.c]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch introduces a new system call for timers events delivered though
file descriptors. This allows timer event to be used with standard POSIX
poll(2), select(2) and read(2). As a consequence of supporting the Linux
f_op->poll subsystem, they can be used with epoll(2) too.
The system call is defined as:
int timerfd(int ufd, int clockid, int flags, const struct itimerspec *utmr);
The "ufd" parameter allows for re-use (re-programming) of an existing timerfd
w/out going through the close/open cycle (same as signalfd). If "ufd" is -1,
s new file descriptor will be created, otherwise the existing "ufd" will be
re-programmed.
The "clockid" parameter is either CLOCK_MONOTONIC or CLOCK_REALTIME. The time
specified in the "utmr->it_value" parameter is the expiry time for the timer.
If the TFD_TIMER_ABSTIME flag is set in "flags", this is an absolute time,
otherwise it's a relative time.
If the time specified in the "utmr->it_interval" is not zero (.tv_sec == 0,
tv_nsec == 0), this is the period at which the following ticks should be
generated.
The "utmr->it_interval" should be set to zero if only one tick is requested.
Setting the "utmr->it_value" to zero will disable the timer, or will create a
timerfd without the timer enabled.
The function returns the new (or same, in case "ufd" is a valid timerfd
descriptor) file, or -1 in case of error.
As stated before, the timerfd file descriptor supports poll(2), select(2) and
epoll(2). When a timer event happened on the timerfd, a POLLIN mask will be
returned.
The read(2) call can be used, and it will return a u32 variable holding the
number of "ticks" that happened on the interface since the last call to
read(2). The read(2) call supportes the O_NONBLOCK flag too, and EAGAIN will
be returned if no ticks happened.
A quick test program, shows timerfd working correctly on my amd64 box:
http://www.xmailserver.org/timerfd-test.c
[akpm@linux-foundation.org: add sys_timerfd to sys_ni.c]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch series implements the new signalfd() system call.
I took part of the original Linus code (and you know how badly it can be
broken :), and I added even more breakage ;) Signals are fetched from the same
signal queue used by the process, so signalfd will compete with standard
kernel delivery in dequeue_signal(). If you want to reliably fetch signals on
the signalfd file, you need to block them with sigprocmask(SIG_BLOCK). This
seems to be working fine on my Dual Opteron machine. I made a quick test
program for it:
http://www.xmailserver.org/signafd-test.c
The signalfd() system call implements signal delivery into a file descriptor
receiver. The signalfd file descriptor if created with the following API:
int signalfd(int ufd, const sigset_t *mask, size_t masksize);
The "ufd" parameter allows to change an existing signalfd sigmask, w/out going
to close/create cycle (Linus idea). Use "ufd" == -1 if you want a brand new
signalfd file.
The "mask" allows to specify the signal mask of signals that we are interested
in. The "masksize" parameter is the size of "mask".
The signalfd fd supports the poll(2) and read(2) system calls. The poll(2)
will return POLLIN when signals are available to be dequeued. As a direct
consequence of supporting the Linux poll subsystem, the signalfd fd can use
used together with epoll(2) too.
The read(2) system call will return a "struct signalfd_siginfo" structure in
the userspace supplied buffer. The return value is the number of bytes copied
in the supplied buffer, or -1 in case of error. The read(2) call can also
return 0, in case the sighand structure to which the signalfd was attached,
has been orphaned. The O_NONBLOCK flag is also supported, and read(2) will
return -EAGAIN in case no signal is available.
If the size of the buffer passed to read(2) is lower than sizeof(struct
signalfd_siginfo), -EINVAL is returned. A read from the signalfd can also
return -ERESTARTSYS in case a signal hits the process. The format of the
struct signalfd_siginfo is, and the valid fields depends of the (->code &
__SI_MASK) value, in the same way a struct siginfo would:
struct signalfd_siginfo {
__u32 signo; /* si_signo */
__s32 err; /* si_errno */
__s32 code; /* si_code */
__u32 pid; /* si_pid */
__u32 uid; /* si_uid */
__s32 fd; /* si_fd */
__u32 tid; /* si_fd */
__u32 band; /* si_band */
__u32 overrun; /* si_overrun */
__u32 trapno; /* si_trapno */
__s32 status; /* si_status */
__s32 svint; /* si_int */
__u64 svptr; /* si_ptr */
__u64 utime; /* si_utime */
__u64 stime; /* si_stime */
__u64 addr; /* si_addr */
};
[akpm@linux-foundation.org: fix signalfd_copyinfo() on i386]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch add an anonymous inode source, to be used for files that need
and inode only in order to create a file*. We do not care of having an
inode for each file, and we do not even care of having different names in
the associated dentries (dentry names will be same for classes of file*).
This allow code reuse, and will be used by epoll, signalfd and timerfd
(and whatever else there'll be).
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Explicitly set pgid and sid of init process to 1.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: <containers@lists.osdl.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Otherwise people get asked about SLUB_DEBUG even if they have another
slab allocator enabled.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
sound: convert "sound" subdirectory to UTF-8
MAINTAINERS: Add cxacru website/mailing list
include files: convert "include" subdirectory to UTF-8
general: convert "kernel" subdirectory to UTF-8
documentation: convert the Documentation directory to UTF-8
Convert the toplevel files CREDITS and MAINTAINERS to UTF-8.
remove broken URLs from net drivers' output
Magic number prefix consistency change to Documentation/magic-number.txt
trivial: s/i_sem /i_mutex/
fix file specification in comments
drivers/base/platform.c: fix small typo in doc
misc doc and kconfig typos
Remove obsolete fat_cvf help text
Fix occurrences of "the the "
Fix minor typoes in kernel/module.c
Kconfig: Remove reference to external mqueue library
Kconfig: A couple of grammatical fixes in arch/i386/Kconfig
Correct comments in genrtc.c to refer to correct /proc file.
Fix more "deprecated" spellos.
Fix "deprecated" typoes.
...
Fix trivial comment conflict in kernel/relay.c.
|
|
Currently there is a circular reference between work queue initialization
and kthread initialization. This prevents the kthread infrastructure from
initializing until after work queues have been initialized.
We want the properties of tasks created with kthread_create to be as close
as possible to the init_task and to not be contaminated by user processes.
The later we start our kthreadd that creates these tasks the harder it is
to avoid contamination from user processes and the more of a mess we have
to clean up because the defaults have changed on us.
So this patch modifies the kthread support to not use work queues but to
instead use a simple list of structures, and to have kthreadd start from
init_task immediately after our kernel thread that execs /sbin/init.
By being a true child of init_task we only have to change those process
settings that we want to have different from init_task, such as our process
name, the cpus that are allowed, blocking all signals and setting SIGCHLD
to SIG_IGN so that all of our children are reaped automatically.
By being a true child of init_task we also naturally get our ppid set to 0
and do not wind up as a child of PID == 1. Ensuring that tasks generated
by kthread_create will not slow down the functioning of the wait family of
functions.
[akpm@linux-foundation.org: use interruptible sleeps]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Display all possible partitions when the root filesystem is not mounted.
This helps to track spell'o's and missing drivers.
Updated to work with newer kernels.
Example output:
VFS: Cannot open root device "foobar" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
0800 8388608 sda driver: sd
0801 192748 sda1
0802 8193150 sda2
0810 4194304 sdb driver: sd
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[akpm@linux-foundation.org: cleanups, fix printk warnings]
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Dave Gilbert <linux@treblig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix some of the spelling issues. Fix sentences. Discourage SLOB use
since SLUB can pack objects denser.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
CONFIG_SLUB_DEBUG can be used to switch off the debugging and sysfs components
of SLUB. Thus SLUB will be able to replace SLOB. SLUB can arrange objects in
a denser way than SLOB and the code size should be minimal without debugging
and sysfs support.
Note that CONFIG_SLUB_DEBUG is materially different from CONFIG_SLAB_DEBUG.
CONFIG_SLAB_DEBUG is used to enable slab debugging in SLAB. SLUB enables
debugging via a boot parameter. SLUB debug code should always be present.
CONFIG_SLUB_DEBUG can be modified in the embedded config section.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove the reference to an external mqueue library since that was
merged into glibc in 2004.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix several typos in help text in Kconfig* files.
Signed-off-by: David Sterba <dave@jikos.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Several people have observed that perhaps LOG_BUF_SHIFT should be in a more
obvious place than under DEBUG_KERNEL. Under some circumstances (such as the
PARISC architecture), DEBUG_KERNEL can increase kernel size, which is an
undesirable trade off for something as trivial as increasing the kernel log
buffer size.
Instead, move LOG_BUF_SHIFT into "General Setup", so that people are more
likely to be able to change it such a circumstance that the default buffer
size is insufficient.
Signed-off-by: Alistair John Strachan <s0348365@sms.ed.ac.uk>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
enhance the initcall_debug boot option:
- measure the time the initcall took to execute and report
it in units of milliseconds.
- show the return code of initcalls (useful to see failures and
to make sure that an initcall hung)
[akpm@linux-foundation.org: fix printk warning]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a proper protype for prepare_namespace() in include/linux/init.h.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make handle_initrd() call try_to_freeze() in a suitable place instead of setting
PF_NOFREEZE for the current task.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for the Analog Devices Blackfin processor architecture, and
currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561
(Dual Core) devices, with a variety of development platforms including those
avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP,
BF561-EZKIT), and Bluetechnix! Tinyboards.
The Blackfin architecture was jointly developed by Intel and Analog Devices
Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in
December of 2000. Since then ADI has put this core into its Blackfin
processor family of devices. The Blackfin core has the advantages of a clean,
orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC
(Multiply/Accumulate), state-of-the-art signal processing engine and
single-instruction, multiple-data (SIMD) multimedia capabilities into a single
instruction-set architecture.
The Blackfin architecture, including the instruction set, is described by the
ADSP-BF53x/BF56x Blackfin Processor Programming Reference
http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf
The Blackfin processor is already supported by major releases of gcc, and
there are binary and source rpms/tarballs for many architectures at:
http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete
documentation, including "getting started" guides available at:
http://docs.blackfin.uclinux.org/ which provides links to the sources and
patches you will need in order to set up a cross-compiling environment for
bfin-linux-uclibc
This patch, as well as the other patches (toolchain, distribution,
uClibc) are actively supported by Analog Devices Inc, at:
http://blackfin.uclinux.org/
We have tested this on LTP, and our test plan (including pass/fails) can
be found at:
http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel
[m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files]
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Aubrey Li <aubrey.li@analog.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a new slab allocator which was motivated by the complexity of the
existing code in mm/slab.c. It attempts to address a variety of concerns
with the existing implementation.
A. Management of object queues
A particular concern was the complex management of the numerous object
queues in SLAB. SLUB has no such queues. Instead we dedicate a slab for
each allocating CPU and use objects from a slab directly instead of
queueing them up.
B. Storage overhead of object queues
SLAB Object queues exist per node, per CPU. The alien cache queue even
has a queue array that contain a queue for each processor on each
node. For very large systems the number of queues and the number of
objects that may be caught in those queues grows exponentially. On our
systems with 1k nodes / processors we have several gigabytes just tied up
for storing references to objects for those queues This does not include
the objects that could be on those queues. One fears that the whole
memory of the machine could one day be consumed by those queues.
C. SLAB meta data overhead
SLAB has overhead at the beginning of each slab. This means that data
cannot be naturally aligned at the beginning of a slab block. SLUB keeps
all meta data in the corresponding page_struct. Objects can be naturally
aligned in the slab. F.e. a 128 byte object will be aligned at 128 byte
boundaries and can fit tightly into a 4k page with no bytes left over.
SLAB cannot do this.
D. SLAB has a complex cache reaper
SLUB does not need a cache reaper for UP systems. On SMP systems
the per CPU slab may be pushed back into partial list but that
operation is simple and does not require an iteration over a list
of objects. SLAB expires per CPU, shared and alien object queues
during cache reaping which may cause strange hold offs.
E. SLAB has complex NUMA policy layer support
SLUB pushes NUMA policy handling into the page allocator. This means that
allocation is coarser (SLUB does interleave on a page level) but that
situation was also present before 2.6.13. SLABs application of
policies to individual slab objects allocated in SLAB is
certainly a performance concern due to the frequent references to
memory policies which may lead a sequence of objects to come from
one node after another. SLUB will get a slab full of objects
from one node and then will switch to the next.
F. Reduction of the size of partial slab lists
SLAB has per node partial lists. This means that over time a large
number of partial slabs may accumulate on those lists. These can
only be reused if allocator occur on specific nodes. SLUB has a global
pool of partial slabs and will consume slabs from that pool to
decrease fragmentation.
G. Tunables
SLAB has sophisticated tuning abilities for each slab cache. One can
manipulate the queue sizes in detail. However, filling the queues still
requires the uses of the spin lock to check out slabs. SLUB has a global
parameter (min_slab_order) for tuning. Increasing the minimum slab
order can decrease the locking overhead. The bigger the slab order the
less motions of pages between per CPU and partial lists occur and the
better SLUB will be scaling.
G. Slab merging
We often have slab caches with similar parameters. SLUB detects those
on boot up and merges them into the corresponding general caches. This
leads to more effective memory use. About 50% of all caches can
be eliminated through slab merging. This will also decrease
slab fragmentation because partial allocated slabs can be filled
up again. Slab merging can be switched off by specifying
slub_nomerge on boot up.
Note that merging can expose heretofore unknown bugs in the kernel
because corrupted objects may now be placed differently and corrupt
differing neighboring objects. Enable sanity checks to find those.
H. Diagnostics
The current slab diagnostics are difficult to use and require a
recompilation of the kernel. SLUB contains debugging code that
is always available (but is kept out of the hot code paths).
SLUB diagnostics can be enabled via the "slab_debug" option.
Parameters can be specified to select a single or a group of
slab caches for diagnostics. This means that the system is running
with the usual performance and it is much more likely that
race conditions can be reproduced.
I. Resiliency
If basic sanity checks are on then SLUB is capable of detecting
common error conditions and recover as best as possible to allow the
system to continue.
J. Tracing
Tracing can be enabled via the slab_debug=T,<slabcache> option
during boot. SLUB will then protocol all actions on that slabcache
and dump the object contents on free.
K. On demand DMA cache creation.
Generally DMA caches are not needed. If a kmalloc is used with
__GFP_DMA then just create this single slabcache that is needed.
For systems that have no ZONE_DMA requirement the support is
completely eliminated.
L. Performance increase
Some benchmarks have shown speed improvements on kernbench in the
range of 5-10%. The locking overhead of slub is based on the
underlying base allocation size. If we can reliably allocate
larger order pages then it is possible to increase slub
performance much further. The anti-fragmentation patches may
enable further performance increases.
Tested on:
i386 UP + SMP, x86_64 UP + SMP + NUMA emulation, IA64 NUMA + Simulator
SLUB Boot options
slub_nomerge Disable merging of slabs
slub_min_order=x Require a minimum order for slab caches. This
increases the managed chunk size and therefore
reduces meta data and locking overhead.
slub_min_objects=x Mininum objects per slab. Default is 8.
slub_max_order=x Avoid generating slabs larger than order specified.
slub_debug Enable all diagnostics for all caches
slub_debug=<options> Enable selective options for all caches
slub_debug=<o>,<cache> Enable selective options for a certain set of
caches
Available Debug options
F Double Free checking, sanity and resiliency
R Red zoning
P Object / padding poisoning
U Track last free / alloc
T Trace all allocs / frees (only use for individual slabs).
To use SLUB: Apply this patch and then select SLUB as the default slab
allocator.
[hugh@veritas.com: fix an oops-causing locking error]
[akpm@linux-foundation.org: various stupid cleanups and small fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The nr_cpu_ids value is currently only calculated in smp_init. However, it
may be needed before (SLUB needs it on kmem_cache_init!) and other kernel
components may also want to allocate dynamically sized per cpu array before
smp_init. So move the determination of possible cpus into sched_init()
where we already loop over all possible cpus early in boot.
Also initialize both nr_node_ids and nr_cpu_ids with the highest value they
could take. If we have accidental users before these values are determined
then the current valud of 0 may cause too small per cpu and per node arrays
to be allocated. If it is set to the maximum possible then we only waste
some memory for early boot users.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
|
|
Clarify the creation of the LOCALVERSION_AUTO string during kernel
configuration, and fix a couple typoes while we're there.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
In init/main.c we have a reference from rest_init() to .init.text
which is intentional.
Rename the function 'init' to 'kernel_init' to make it a
kernel wide unique symbol and whitelist the reference.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
Let's allow page-alignment in general for per-cpu data (wanted by Xen, and
Ingo suggested KVM as well).
Because larger alignments can use more room, we increase the max per-cpu
memory to 64k rather than 32k: it's getting a little tight.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
initramfs ended up depending on BLOCK:
INITRAMFS_SOURCE <-- BLK_DEV_INITRD <-- BLOCK
This inhibits use of customized-initramfs-over-ramfs without block layer
(ramfs would still be enabled), useful in embedded applications.
Move BLK_DEV_INITRD out of 'drivers/block/Kconfig' and into 'init/Kconfig',
make it unconditional.
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
