Age | Commit message (Collapse) | Author | Files | Lines |
|
This patch is to disable the USB ports unconnected to USB3503. In order to
disable the port, 'port_off_mask' must be set.
* Disable PORT1 only
.port_off_mask = USB3503_OFF_PORT1;
* Disable PORT1 and PORT3 only
.port_off_mask = USB3503_OFF_PORT1 | USB3503_OFF_PORT3;
* Enables all ports
.port_off_mask = 0;
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mszyprow: mainline commit e8e44a4896a5f0bde1af36a31b7ec662bdaa44ef]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: Ie8e44a4896a5f0bde1af36a31b7ec662bdaa44ef
|
|
Commit f792685006274a850e6cc0ea9ade275ccdfc90bc ("math64: New
div64_u64_rem helper") implemented div64_u64 in terms of div64_u64_rem.
But div64_u64_rem was removed because it slowed down div64_u64 (and
there were no other users of div64_u64_rem).
Device Mapper's I/O statistics support has a need for div64_u64_rem;
reintroduce this helper as a separate method that doesn't slow down
div64_u64, especially on 32-bit systems.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
[backport]
Signed-off-by: Maciej Wereski <m.wereski@partner.samsung.com>
Change-Id: Icd721ff57c6d127e7acb0bf17d233d0a50ff24da
|
|
Pages allocated from MIGRATE_RESERVE migratetype pageblocks
are not freed back to MIGRATE_RESERVE migratetype free
lists in free_pcppages_bulk()->__free_one_page() if we got
to free_pcppages_bulk() through drain_[zone_]pages().
The freeing through free_hot_cold_page() is okay because
freepage migratetype is set to pageblock migratetype before
calling free_pcppages_bulk(). If pages of MIGRATE_RESERVE
migratetype end up on the free lists of other migratetype
whole Reserved pageblock may be later changed to the other
migratetype in __rmqueue_fallback() and it will be never
changed back to be a Reserved pageblock. Fix the issue by
preserving freepage migratetype as a pageblock migratetype
(instead of overriding it to the requested migratetype)
for MIGRATE_RESERVE migratetype pages in rmqueue_bulk().
The problem was introduced in v2.6.31 by commit ed0ae21
("page allocator: do not call get_pageblock_migratetype()
more than necessary").
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reported-by: Yong-Taek Lee <ytk.lee@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: I1d4ab2a3241387160dd376b0ead864cd2b0c59f0
|
|
Adds support for limitation of maximal pixel clock of HDMI
signal. This feature is needed on boards that contains
lines or bridges with frequency limitations.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Change-Id: I4cc38e995feeaca77b73e9ea0197d67f99d57715
|
|
This patch adds support for propagation of setup of clock's parent one level
up.
This feature is helpful when a driver changes topology of its clocks using
clk_set_parent(). The problem occurs when on one platform/SoC driver's clock
is located at MUX output but on the other platform/SoC there is a gated proxy
clock between the MUX and driver's clock. In such a case, driver's code has to
be modified to use one clock for enabling and the other clock for setup of a
parent.
The code updates are avoided by propagating setup of a parent up one level.
Additionally, this patch adds CLK_SET_PARENT_PARENT (sorry for naming) flag to
inform clk-core that clk_set_parent() should be propagated.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Change-Id: I206d23fb86cc09bce943ef9971a710876e3a7744
|
|
There are no old function interface users left, so the old interface can
be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
compatibility
This is required in order to integrate configfs support.
f_fs needs to be a separately compiled module and so it needs to use the new
interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This will be required in order to use the new function interface
(usb_get_function_instance/usb_put_function_instance)
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyunmgin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
USB function's configfs config group is created in a generic way in
usb/gadget/configfs.c:function_make(), which in turn delegates actual
allocation and setup of the USB function instance to a particular
implementation, e.g. in f_acm.c. The said implementation does its job
in a parameter-less function e.g. acm_alloc_instance(), which results
in creating an unnamed config group, whose name is set later in
function_make(). function_make() creates the name by parsing a string
of the form:
<function name>.<instance name>
which comes from userspace as a parameter to mkdir invocation.
Up to now only <function name> has been used, while <instance name>
has been ignored. This patch adds a set_inst_name() operation to
struct usb_function_instance which allows passing the <instance name>
from function_make() so that it is not ignored. It is entirely up to the
implementor of set_inst_name() what to do with the <instance name>.
In a typical case, the struct usb_function_instance is embedded in a
larger struct which is retrieved in set_inst_name() with container_of(),
and the larger struct contains a field to store the <instance name>.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Due to USB controllers may have different restrictions, usb gadget layer
needs to provide a generic way to inform gadget functions to complain
with non-standard requirements.
This patch adds 'quirk_ep_out_aligned_size' field to struct usb_gadget
to inform when controller's epout requires buffer size to be aligned to
MaxPacketSize. A helper is also provided to align buffer size when
necessary.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[backport from mainline]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
|
|
This patch moves all bitflags to the end of usb_gadget struct in order
to improve readability.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[backport from mainline]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
|
|
Make it easier to create attributes without having to always audit the
mode settings.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A number of parts of the kernel created their own version of this, might
as well have the sysfs core provide it instead.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mainline backport]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
|
|
Since everybody sets kstrdup()ed constant string to "struct xattr"->name but
nobody modifies "struct xattr"->name , we can omit kstrdup() and its failure
checking by constifying ->name member of "struct xattr".
Change-Id: I6cb5cd7f29c01956dd0d1579af81a518a5936071
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Joel Becker <jlbec@evilplan.org> [ocfs2]
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
|
|
The interface to request security labels from user space is the xattr
interface. When requesting the security label from an NFS server it is
important to make sure the requested xattr actually is a MAC label. This allows
us to make sure that we get the desired semantics from the attribute instead of
something else such as capabilities or a time based LSM.
Change-Id: I283f116953f958877826ba772661b5755986ac99
Acked-by: Eric Paris <eparis@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Matthew N. Dodd <Matthew.Dodd@sparta.com>
Signed-off-by: Miguel Rodel Felipe <Rodel_FM@dsi.a-star.edu.sg>
Signed-off-by: Phua Eu Gene <PHUA_Eu_Gene@dsi.a-star.edu.sg>
Signed-off-by: Khin Mi Mi Aung <Mi_Mi_AUNG@dsi.a-star.edu.sg>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
|
|
This patch introduces new cpufreq governor named 'LAB'.
LAB governor will use scheduler, per-CPU information to determine how many
CPUs are in busy now. As a result the number of idle CPUs is calculated
for current load (digital low pass filtering is used to provide more stable
results). It will determine next frequency.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Conflicts:
drivers/cpufreq/cpufreq_governor.c
Resolved-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Define a PWM_POLARITY_INVERTED macro in include/dt-bindings/pwm/pwm.h to
be used by device tree sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This patch introduces new Samsung PWM driver, which is completely
rewritten to be multiplatform- and DeviceTree-aware.
In addition, remaining problems of old driver are fixed, such as:
- proper handling of hardware variants,
- synchronization on SMP systems,
- handling of boundary parameter values,
- hardware sharing with PWM clocksource driver,
- undefined state of PWM output after stopping PWM channel.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add a simple sysfs interface to the generic PWM framework.
/sys/class/pwm/
`-- pwmchipN/ for each PWM chip
|-- export (w/o) ask the kernel to export a PWM channel
|-- npwm (r/o) number of PWM channels in this PWM chip
|-- pwmX/ for each exported PWM channel
| |-- duty_cycle (r/w) duty cycle (in nanoseconds)
| |-- enable (r/w) enable/disable PWM
| |-- period (r/w) period (in nanoseconds)
| `-- polarity (r/w) polarity of PWM (normal/inversed)
`-- unexport (w/o) return a PWM channel to the kernel
Based on work by Lars Poeschel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add omitted codes from commits,
<commit-id d9e6913d1> "drivers: thermal: add check when ~ ", and
<commit-id efbf8d7a3> "thermal: thermal_core: allow binding with ~"
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
Update the BOOST framework core to be compliant with v9 version of the patch
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch provides auto disable/enable operation for boost. When any
defined trip point is passed, the boost is disabled.
In that moment thermal monitor workqueue is woken up and it monitors
if the device temperature drops below 75% of the smallest trip point.
When device cools down, the boost is enabled again.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Changes for v6:
- Disable boost only when supported and enabled
- Protect boost related thermal_zone_device struct fields with mutex
- Evaluate temperature trend during boost enable decision
- Create separate methods to handle boost enable/disable
(thermal_boost_{enable|disable}) operations
- Boost is disabled at any trip point passage (not only the non critical one)
Changes for v5:
- Move boost disable code from cpu_cooling.c to thermal_core.c
(to handle_non_critical_trips)
- Extent struct thermal_zone_device by adding overheated bool flag
- Implement auto enable of boost after device cools down
- Introduce boost_polling flag, which indicates if thermal uses it's predefined
pool delay or has woken up thermal workqueue only to wait until device
cools down.
Changes for v4:
- New patch
|
|
This commit adds boost frequency support in cpufreq core (Hardware &
Software).
Some SoC (like Exynos4 - e.g. 4x12) allow setting frequency above
its normal operation limits. Such a mode shall be only used for a short
time.
Overclocking (boost) support is essentially provided by platform
dependent cpufreq driver.
This commit unifies support for SW and HW (Intel) overclocking solutions
in the core cpufreq driver. Previously the "boost" sysfs attribute was
defined at acpi driver code.
By default boost is disabled. One global attribute is available at:
/sys/devices/system/cpu/cpufreq/boost.
It only shows up when cpufreq driver supports overclocking.
Under the hood frequencies dedicated for boosting are marked with a
special flag (CPUFREQ_BOOST_FREQ) at driver's frequency table.
It is the user's concern to enable/disable overclocking with proper call to
sysfs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Changes for v6:
- Remove sysfs boost attribute when subsys_iterface_unregister() fails
- Move global boost_enabled variable from cpufreq.c to platform dependent
struct cpufreq_driver
- pr_err() message is also printed when boost disable fails
Changes for v5:
- Rename cpufreq_boost_trigger_state_sw() to cpufreq_boost_enable_sw()
- Extent cpufreq_register_driver() to check if cpufreq driver provided
boost_enable callback. If not provided, then use cpufreq_boost_enable_sw()
- Use single call to cpufreq_driver->enable_boost() with cpufreq driver
provided callback or default SW boost enable routine
- Move pr_debug call to store_boost() from cpufreq_boost_trigger_state()
- Change the user_policy.max value when SW boost is toggled. It is necessary
for proper operation of e.g. thermal subsystem.
- Add check if cpufreq_driver pointer is not NULL at
cpufreq_boost_supported() routine
- Add EXPORT_SYMBOL_GPL for cpufreq_boost_supported() and
cpufreq_boost_enabled()
- Remove extra check for cpufreq_boost_supported() at
cpufreq_freq_table_cpuinfo()
- Explanation of show boost logic at show_available_freqs()
- Add cpufreq_set_boost_enabled() method to set initial value of boost_enabled
global flag
Changes for v4:
- Remove boost parameter from cpufreq_frequency_table_cpuinfo() function
- Introduce cpufreq_boost_supported() method
- Use of cpufreq_boost_supported() and cpufreq_boost_enabled() to decide
if frequency shall be skipped
- Rename set_boost_freq() to enable_boost()
- cpufreq_attr_available_freq() moved to freq_table.c
- Use policy list to get access to cpufreq policies
- Rename global boost flag (cpufreq_boost_enabled -> boost_enabled)
- pr_err corrected ( %sable)
- Remove sanity check at cpufreq_boost_trigger_state() entrance [to test if
boost is supported]
- Use either HW (boost_enable) callback or SW managed boost
- Introduce new cpufreq_boost_trigger_state_sw() method to handle boost
at SW.
- Protect boost_enabled manipulation with lock.
Changes for v3:
- Method for reading boost status
- Removal of cpufreq_frequency_table_max()
- Extent cpufreq_frequency_table_cpuinfo() to support boost parameter
- boost_supported flag added to cpufreq_driver struct
- "boost" sysfs attribute control flag removed
- One global flag describing state of the boost defined at cpufreq core
- Rename cpufreq_driver's low_level_boost field to set_boost_freq()
- Usage of cpufreq_sysfs_{remove|add}_file() routines
Changes for v2:
- Removal of cpufreq_boost structure and move its fields to cpufreq_driver
structure
- Flag to indicate if global boost attribute is already defined
- Extent the pr_{err|debbug} functions to show current function names
|
|
Policies available in a cpufreq framework are now linked together. They are
accessible via cpufreq_policy_list defined at cpufreq core.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Changes for v6:
- Move policy list entry delete code to __cpufreq_remove_dev()
Changes for v5:
- Call list_add() only when device successfully added
Changes for v4:
- New patch
|
|
When we don't have any file in cpu/cpufreq directory we shouldn't
create it. Specially with the introduction of per-policy governor
instance patchset, even governors are moved to
cpu/cpu*/cpufreq/governor-name directory and so this directory is
just not required.
Lets have it only when required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This platdata is related with buffer size.
It's increaed the performance.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
With this patch, charger-manager can support device tree fully.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
During the charger manager driver's probing time, it can't succeed
if there's no pre-defined .temperature_out_of_range callback function.
But if fuel gauge supports battery temperature measurement, we
can use it directly. That's what cm_default_get_temp() function does.
With flag measure_batter_temp ON, we normally use cm_default_get_temp()
for .temperature_out_of_range callback funtion.
The TEMP_AMBIENT property is only used for pre-defined one.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
Added an API of_extcon_get_extcon_dev() to be used by drivers to get
extcon device in the case of dt boot (this can be used instead of
extcon_get_extcon_dev()).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
|
|
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
- Remove duplicated macro data.
- Improve readability.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
enum type has variable size depending on compiler options,
so it should be avoided in structs passed to userland.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
This commit fixes the way gadget's pullup method (wrapped at
usb_gadget_connect/disconnect) is called in the udc-core.
The composite driver allows correct driver registration, even when it calls
the usb_gadget_disconnect method (composite driver configuration is defered
for user space - please look into the description of usb_composite_probe at
composite.c - line: 1623)
One such example is the CCG (Configurable Composite Gadget) driver (at
drivers/staging/ccg), which after its registration has no usb descriptor
(i.e. idProduct, idVendor etc.) and functions registered. Those are configured
after writing to /sys/module/g_ccg/parameters/ or /sys/class/ccg_usb/ccg0/.
Unfortunately, the code at 'usb_gadget_probe_driver' method (some code omitted):
if (udc_is_newstyle(udc)) {
bind(udc->gadget);
usb_gadget_udc_start(udc->gadget, driver);
usb_gadget_connect(udc->gadget);
}
Explicitly calls the usb_gadget_connect method for this driver. It looks like
the udc-core enables pullup for a driver, which has no functions and no
descriptor filled (those values are feed from userspace).
The USB composite driver API allows correct driver registration with calling
usb_gadget_disconnect method, but as it is now, _ALL_ newstyle usb gadgets are
connected by default. Therefore it violates the composite API.
The solution (at least until the udc-core is reworked) is to add atomic
variable, which helps in balancing the number of called usb_gadget_connect/
disconnect functions.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
This patch adds ioctl helpers to the V4L2 mem-to-mem API, so we can avoid
several ioctl handlers in the mem-to-mem video node drivers that are simply
a pass-through to the v4l2_m2m_* calls. These helpers will only be useful
for drivers that use same mutex for both OUTPUT and CAPTURE queue, which
is the case for all currently in tree v4l2 m2m drivers. In order to use
the helpers the drivers are required to use struct v4l2_fh.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
Changes since v1:
- added v4l2_m2m_ioctl_create_buf().
|
|
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
|
|
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
This patch add extcon-port driver which maintain compatibility with old JACK
driver(drivers/misc/jack.c). extcon-port driver send uevent to user-space
when receive notification of cable state from EXTCON.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Conflicts:
drivers/extcon/Kconfig
drivers/extcon/Makefile
|
|
As pointed by Russell in [1], the sg properties are already availble in struct device,
so no need to duplicate here.
[1]: http://marc.info/?l=linux-omap&m=137416733628831
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The problem here is that the dma_xfer() functions in
drivers/ata/pata_arasan_cf.c and drivers/mtd/nand/fsmc_nand.c expect
dma_submit_error() to return an error code so they return 1 when they
intended to return a negative.
So far as I can tell, none of the ->tx_submit() functions ever do
return error codes so this patch should have no effect in the current
code.
I also changed it from a define to an inline.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <djbw@fb.com>
|
|
Suggested by Arnd, add dma_get_slave_channel interface
Dma host driver could get specific channel specificied by request line, rather than filter.
host example:
static struct dma_chan *xx_of_dma_simple_xlate(struct of_phandle_args *dma_spec,
struct of_dma *ofdma)
{
struct xx_dma_dev *d = ofdma->of_dma_data;
unsigned int request = dma_spec->args[0];
if (request > d->dma_requests)
return NULL;
return dma_get_slave_channel(&(d->chans[request].vc.chan));
}
probe:
of_dma_controller_register((&op->dev)->of_node, xx_of_dma_simple_xlate, d);
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
add new device callback .device_slave_caps api which can be used by clients to
query the dma channel capablties before they program the channel. This can help
is removing errors during the channel programming. Also add helper
dma_slave_get_caps API
This patch folds the work done by Matt earlier
https://patchwork.kernel.org/patch/2094891/
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Use the generic PHY API instead of the platform callback to control
the MIPI DSIM DPHY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
Changes since v4:
- updated to latest version of the PHY framework - removed PHY
labels.
|
|
Use the generic PHY API instead of the platform callback to control
the MIPI CSIS DPHY. The 'phy_label' field is added to the platform
data structure to allow PHY lookup on non-dt platforms
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
Changes since v4:
- updated to latest version of the PHY framework - removed PHY
labels.
|
|
The PHY framework provides a set of APIs for the PHY drivers to
create/destroy a PHY and APIs for the PHY users to obtain a reference to the
PHY with or without using phandle. For dt-boot, the PHY drivers should
also register *PHY provider* with the framework.
PHY drivers should create the PHY by passing id and ops like init, exit,
power_on and power_off. This framework is also pm runtime enabled.
The documentation for the generic PHY framework is added in
Documentation/phy.txt and the documentation for dt binding can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This reverts commit 528bac1d1f2a8bb10ebc3e56dd8f22e2d76f197f.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This reverts commit 88d0875e5d8cb005a3c21dff52581b08b6fd22eb.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This reverts commit 304105d59b61ac6800a274cdcf8f618b5007456a.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This reverts commit 80ca90cdf56ed7a375e31275fde4282e22f8edba.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This patch adds 'sync-on-green-active' property as part
of endpoint property.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|