summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)AuthorFilesLines
2014-11-18upstream: [media] v4l: add RF tuner gain controlsAntti Palosaari1-0/+11
Modern silicon RF tuners used nowadays has many controllable gain stages on signal path. Usually, but not always, there is at least 3 gain stages. Also on some cases there could be multiple gain stages within the ones specified here. However, I think that having these three controllable gain stages offers enough fine-tuning for real use cases. 1) LNA gain. That is first gain just after antenna input. 2) Mixer gain. It is located quite middle of the signal path, where RF signal is down-converted to IF/BB. 3) IF gain. That is last gain in order to adjust output signal level to optimal level for receiving party (usually demodulator ADC). Each gain stage could be set rather often both manual or automatic (AGC) mode. Due to that add separate controls for controlling operation mode. Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2: Add settings for Horizontal and Vertical MV Search RangeAmit Grover1-0/+2
Adding V4L2 controls for horizontal and vertical search range in pixels for motion estimation module in video encoder. Signed-off-by: Swami Nathan <swaminath.p@samsung.com> Signed-off-by: Amit Grover <amit.grover@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media, edac] Change my email addressMauro Carvalho Chehab2-2/+2
There are several left overs with my old email address. Remove their occurrences and add myself at CREDITS, to allow people to be able to reach me on my new addresses. Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] media: rc: add Sharp infrared protocolJames Hogan1-1/+3
Add Sharp infrared protocol constants RC_TYPE_SHARP and RC_BIT_SHARP. Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2-dv-timings.h: add new 4K DMT resolutionsHans Verkuil1-0/+17
VESA added two new DMT timings in their latest standard document. Add these to v4l2-dv-timings.h. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] saa6588: add support for non-blocking modeHans Verkuil1-0/+1
saa6588 always blocked while waiting for data, even if the filehandle was in non-blocking mode. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] saa6588: remove unused CMD_OPENHans Verkuil1-1/+0
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] vb2: retry start_streaming in case of insufficient buffersHans Verkuil1-4/+11
If start_streaming returns -ENOBUFS, then it will be retried the next time a buffer is queued. This means applications no longer need to know how many buffers need to be queued before STREAMON can be called. This is particularly useful for output stream I/O. If a DMA engine needs at least X buffers before it can start streaming, then for applications to get a buffer out as soon as possible they need to know the minimum number of buffers to queue before STREAMON can be called. You can't just try STREAMON after every buffer since on failure STREAMON will dequeue all your buffers. (Is that a bug or a feature? Frankly, I'm not sure). This patch simplifies applications substantially: they can just call STREAMON at the beginning and then start queuing buffers and the DMA engine will kick in automagically once enough buffers are available. This also fixes using write() to stream video: the fileio implementation calls streamon without having any queued buffers, which will fail today for any driver that requires a minimum number of buffers. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] vb2: push the mmap semaphore down to __buf_prepare()Hans Verkuil1-0/+2
Rather than taking the mmap semaphore at a relatively high-level function, push it down to the place where it is really needed. It was placed in vb2_queue_or_prepare_buf() to prevent racing with other vb2 calls. The only way I can see that a race can happen is when two threads queue the same buffer. The solution for that it to introduce a PREPARING state. Moving it down offers opportunities to simplify the code. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: atmel-isi: Should clear bits before set the hardware ↵Josh Wu1-0/+2
register In the ISI driver it reads the config register to get original value, then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will cause some bits overlap. So we need to clear these bits first, then set correct value. This patch fix it. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] si4713: move supply list to si4713_platform_dataDinesh Ram1-0/+2
The supply list is needed by the platform driver, but not by the usb driver. So this information belongs to the platform data and should not be hardcoded in the subdevice driver. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Eduardo Valentin <edubezval@gmail.com> Acked-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: of: Remove struct v4l2_of_endpoint remote fieldLaurent Pinchart1-2/+0
The field isn't set when parsing the endpoint. Remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: of: Return an int in v4l2_of_parse_endpoint()Laurent Pinchart1-2/+2
When CONFIG_OF is not defined the v4l2_of_parse_endpoint() function is defined as a stub that returns -ENOSYS. Make the real function return an integer as well to be able to differentiate between the two cases. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: vsp1: Add LUT supportLaurent Pinchart2-1/+36
The Look-Up Table looks up values in 8-bit indexed tables separately for each color component. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: vsp1: Add SRU supportLaurent Pinchart1-0/+1
The Super Resolution Unit performs super resolution processing with optional upscaling by a factor of two. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: Add media format codes for AHSV8888 on 32-bit bussesLaurent Pinchart1-0/+3
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] videobuf2: Add missing lock held on vb2_fop_releaseRicardo Ribalda1-0/+1
vb2_fop_release does not hold the lock although it is modifying the queue->owner field. This could lead to race conditions on the vb2_perform_io function when multiple applications are accessing the video device via read/write API: [ 308.297741] BUG: unable to handle kernel NULL pointer dereference at 0000000000000260 [ 308.297759] IP: [<ffffffffa07a9fd2>] vb2_perform_fileio+0x372/0x610 [videobuf2_core] [ 308.297794] PGD 159719067 PUD 158119067 PMD 0 [ 308.297812] Oops: 0000 #1 SMP [ 308.297826] Modules linked in: qt5023_video videobuf2_dma_sg qtec_xform videobuf2_vmalloc videobuf2_memops videobuf2_core qtec_white qtec_mem gpio_xilinx qtec_cmosis qtec_pcie fglrx(PO) spi_xilinx spi_bitbang qt5023 [ 308.297888] CPU: 1 PID: 2189 Comm: java Tainted: P O 3.11.0-qtec-standard #1 [ 308.297919] Hardware name: QTechnology QT5022/QT5022, BIOS PM_2.1.0.309 X64 05/23/2013 [ 308.297952] task: ffff8801564e1690 ti: ffff88014dc02000 task.ti: ffff88014dc02000 [ 308.297962] RIP: 0010:[<ffffffffa07a9fd2>] [<ffffffffa07a9fd2>] vb2_perform_fileio+0x372/0x610 [videobuf2_core] [ 308.297985] RSP: 0018:ffff88014dc03df8 EFLAGS: 00010202 [ 308.297995] RAX: 0000000000000000 RBX: ffff880158a23000 RCX: dead000000100100 [ 308.298003] RDX: 0000000000000000 RSI: dead000000200200 RDI: 0000000000000000 [ 308.298012] RBP: ffff88014dc03e58 R08: 0000000000000000 R09: 0000000000000001 [ 308.298020] R10: ffffea00051e8380 R11: ffff88014dc03fd8 R12: ffff880158a23070 [ 308.298029] R13: ffff8801549040b8 R14: 0000000000198000 R15: 0000000001887e60 [ 308.298040] FS: 00007f65130d5700(0000) GS:ffff88015ed00000(0000) knlGS:0000000000000000 [ 308.298049] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 308.298057] CR2: 0000000000000260 CR3: 0000000159630000 CR4: 00000000000007e0 [ 308.298064] Stack: [ 308.298071] ffff880156416c00 0000000000198000 0000000000000000 ffff880100000001 [ 308.298087] ffff88014dc03f50 00000000810a79ca 0002000000000001 ffff880154904718 [ 308.298101] ffff880156416c00 0000000000198000 ffff880154904338 ffff88014dc03f50 [ 308.298116] Call Trace: [ 308.298143] [<ffffffffa07aa3c4>] vb2_read+0x14/0x20 [videobuf2_core] [ 308.298198] [<ffffffffa07aa494>] vb2_fop_read+0xc4/0x120 [videobuf2_core] [ 308.298252] [<ffffffff8154ee9e>] v4l2_read+0x7e/0xc0 [ 308.298296] [<ffffffff8116e639>] vfs_read+0xa9/0x160 [ 308.298312] [<ffffffff8116e882>] SyS_read+0x52/0xb0 [ 308.298328] [<ffffffff81784179>] tracesys+0xd0/0xd5 [ 308.298335] Code: e5 d6 ff ff 83 3d be 24 00 00 04 89 c2 4c 8b 45 b0 44 8b 4d b8 0f 8f 20 02 00 00 85 d2 75 32 83 83 78 03 00 00 01 4b 8b 44 c5 48 <8b> 88 60 02 00 00 85 c9 0f 84 b0 00 00 00 8b 40 58 89 c2 41 89 [ 308.298487] RIP [<ffffffffa07a9fd2>] vb2_perform_fileio+0x372/0x610 [videobuf2_core] [ 308.298507] RSP <ffff88014dc03df8> [ 308.298514] CR2: 0000000000000260 [ 308.298526] ---[ end trace e8f01717c96d1e41 ]--- Signed-off-by: Ricardo Ribalda <ricardo.ribalda@gmail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] media: Add pad flag MEDIA_PAD_FL_MUST_CONNECTSakari Ailus1-0/+1
Pads that set this flag must be connected by an active link for the entity to stream. Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2014-11-18upstream: [media] v4l: omap4iss: Add support for OMAP4 camera interface - CoreSergio Aguirre1-0/+65
This adds a very simplistic driver to utilize the CSI2A interface inside the ISS subsystem in OMAP4, and dump the data to memory. Check Documentation/video4linux/omap4_camera.txt for details. This commit adds the driver core, registers definitions and documentation. Signed-off-by: Sergio Aguirre <sergio.a.aguirre@gmail.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2014-11-18upstream: [media] videobuf2: Add support for file access mode flags for ↵Philipp Zabel1-1/+1
DMABUF exporting Currently it is not possible for userspace to map a DMABUF exported buffer with write permissions. This patch allows to also pass O_RDONLY/O_RDWR when exporting the buffer, so that userspace may map it with write permissions. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: Fix typo in v4l2_subdev_get_try_crop()Laurent Pinchart1-1/+1
The helper function is defined by a macro that is erroneously called with the compose rectangle instead of the crop rectangle. Fix it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] V4L2: (cosmetic) remove redundant use of unlikely()Guennadi Liakhovetski1-2/+2
BUG*() and WARN*() macros specify their conditions as unlikely, using BUG_ON(unlikely(condition)) is redundant, remove it. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: ti-vpe: Add VPE mem to mem driverArchit Taneja1-0/+4
VPE is a block which consists of a single memory to memory path which can perform chrominance up/down sampling, de-interlacing, scaling, and color space conversion of raster or tiled YUV420 coplanar, YUV422 coplanar or YUV422 interleaved video formats. We create a mem2mem driver based primarily on the mem2mem-testdev example. The de-interlacer, scaler and color space converter are all bypassed for now to keep the driver simple. Chroma up/down sampler blocks are implemented, so conversion beteen different YUV formats is possible. Each mem2mem context allocates a buffer for VPE MMR values which it will use when it gets access to the VPE HW via the mem2mem queue, it also allocates a VPDMA descriptor list to which configuration and data descriptors are added. Based on the information received via v4l2 ioctls for the source and destination queues, the driver configures the values for the MMRs, and stores them in the buffer. There are also some VPDMA parameters like frame start and line mode which needs to be configured, these are configured by direct register writes via the VPDMA helper functions. The driver's device_run() mem2mem op will add each descriptor based on how the source and destination queues are set up for the given ctx, once the list is prepared, it's submitted to VPDMA, these descriptors when parsed by VPDMA will upload MMR registers, start DMA of video buffers on the various input and output clients/ports. When the list is parsed completely(and the DMAs on all the output ports done), an interrupt is generated which we use to notify that the source and destination buffers are done. The rest of the driver is quite similar to other mem2mem drivers, we use the multiplane v4l2 ioctls as the HW support coplanar formats. Signed-off-by: Archit Taneja <archit@ti.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: consolidate the reassignments of ->f_op in ->open() instancesAl Viro1-0/+11
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2014-11-18upstream: [media] v4l2-fh: Include linux/videodev2.h for enum v4l2_priority ↵Laurent Pinchart1-0/+1
definition struct v4l2_fh has an enum v4l2_priority field. Make sure the enum definition is available by including linux/videodev2.h. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2-fh: Include linux/fs.h for struct file definitionLaurent Pinchart1-0/+1
v4l2-fh.h dereferences struct file, the structure must thus be defined. Pull in its definition by including linux/fs.h. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2-ctrls: Correct v4l2_ctrl_get_int_menu() function's ↵Sylwester Nawrocki1-1/+1
return type Remove the redundant 'const' qualifiers from the function signature and from the qmenu_int arrays' declarations. Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2-ctrls: fix typo in header file media/v4l2-ctrls.hFrank Schaefer1-1/+1
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: treewide: Fix common typo in "identify"Maxime Jayat4-4/+4
Correct common misspelling of "identify" as "indentify" throughout the kernel Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-11-18upstream: [media] videobuf2-dma-sg: Replace vb2_dma_sg_desc with sg_tableRicardo Ribalda1-8/+2
Replace the private struct vb2_dma_sg_desc with the struct sg_table so we can benefit from all the helping functions in lib/scatterlist.c for things like allocating the sg or compacting the descriptor. marvel-ccic and solo6x10 drivers, that use this API have been updated. Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> [s.nawrocki@samsung.com: minor corrections of the changelog] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] videobuf2: Fix vb2_write prototypeRicardo Ribalda1-2/+2
struct v4_file_operations defines the data param as const char __user *data but on vb2 is defined as char __user *data. This patch fixes the warnings produced by this. ie: drivers/qtec/qtec_xform.c:817:2: warning: initialization from incompatible pointer type [enabled by default] drivers/qtec/qtec_xform.c:817:2: warning: (near initialization for ‘qtec_xform_v4l_fops.write’) [enabled by default] Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] adv7511: add new video encoderHans Verkuil1-0/+48
This is an Analog Devices HDMI transmitter. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] smiapp: Call the clock "ext_clk"Sakari Ailus1-1/+0
As the clock framework makes it possible to assign a device specific name to the clocks, remove the ability to use a named clock in the driver. Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] mt9v032: Use the common clock frameworkLaurent Pinchart1-4/+0
Configure the device external clock using the common clock framework instead of a board code callback function. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: v4l2-common: warning fix (W=1): add a missed function prototypeMauro Carvalho Chehab1-0/+1
changeset d1e9b7c12 added a new ancilliary function to API, but forgot to add it to the corresponding header file. drivers/media/v4l2-core/v4l2-ctrls.c:568:18: warning: no previous prototype for 'v4l2_ctrl_get_int_menu' [-Wmissing-prototypes] const s64 const *v4l2_ctrl_get_int_menu(u32 id, u32 *len) Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] saa7115: make multi-line comments compliant with CodingStyleMauro Carvalho Chehab1-20/+29
changeset 2ccf12a did a crappy job when added multi-line comment lines, violating CodingStyle. Change the comments added there to fulfill CodingStyle, and document the platform_data using Documentation/kernel-doc-nano-HOWTO.txt. Cc: Jon Arne Jørgensen <jonarne@jonarne.no> Cc: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] saa7115: Implement i2c_board_info.platform_dataJon Arne Jørgensen1-0/+64
This patch implements i2c_board_info.platform_data, and some options to override the default initialization table for the GM7113C and SAA7113 chips. Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] videodev2.h: defines to calculate blanking and frame sizesHans Verkuil1-0/+10
It is very common to have to calculate the total width and height of the blanking and the full frame, so add a few defines that deal with that. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2-dv-timings: add new helper moduleHans Verkuil1-0/+67
This module makes it easy to filter valid timings from the full list of CEA and DMT timings based on the timings capabilities. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l2-dv-timings.h: remove duplicate V4L2_DV_BT_DMT_1366X768P60Hans Verkuil1-8/+0
This particular DMT timing definition was duplicated in the header. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] tea575x: Move header from sound to mediaOndrej Zary1-0/+0
Move include/sound/tea575x-tuner.h to include/media/tea575x.h and update files that include it. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: Renesas R-Car VSP1 driverLaurent Pinchart1-0/+25
The VSP1 is a video processing engine that includes a blender, scalers, filters and statistics computation. Configurable data path routing logic allows ordering the internal blocks in a flexible way. Due to the configurable nature of the pipeline the driver implements the media controller API and doesn't use the V4L2 mem-to-mem framework, even though the device usually operates in memory to memory mode. Only the read pixel formatters, up/down scalers, write pixel formatters and LCDC interface are supported at this stage. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: Add V4L2_PIX_FMT_NV16M and V4L2_PIX_FMT_NV61M formatsLaurent Pinchart1-0/+2
NV16M and NV61M are planar YCbCr 4:2:2 and YCrCb 4:2:2 formats with a luma plane followed by an interleaved chroma plane. The planes are not required to be contiguous in memory, and the formats can only be used with the multi-planar formats API. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] v4l: Add media format codes for ARGB8888 and AYUV8888 on ↵Laurent Pinchart1-2/+4
32-bit busses Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] media: vb2: Clarify queue_setup() and buf_prepare() usage ↵Laurent Pinchart1-4/+7
documentation Explain how the two operations must handle formats and validate buffer sizes when used with VIDIOC_CREATE_BUFS. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] V4L: Add VP8 encoder controlsArun Kumar K1-0/+29
This patch adds new V4L controls for VP8 encoding. Signed-off-by: Kiran AVND <avnd.kiran@samsung.com> Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: include: Convert ethernet mac address declarations to use ETH_ALENJoe Perches11-45/+58
It's convenient to have ethernet mac addresses use ETH_ALEN to be able to grep for them a bit easier and also to ensure that the addresses are __aligned(2). Add #include <linux/if_ether.h> as necessary. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-18upstream: [media] media: lirc: Allow lirc dev to talk to rc deviceSrinivas Kandagatla1-0/+1
The use case is simple, if any rc device has allowed protocols = RC_TYPE_LIRC and map_name = RC_MAP_LIRC set, the driver open will be never called. The reason for this is, all of the key maps except lirc have some KEYS in there map, so during rc_register_device process these keys are matched against the input drivers and open is performed, so for the case of RC_MAP_EMPTY, a vt/keyboard is matched and the driver open is performed. In case of lirc, there is no match and result is that there is no open performed, however the lirc-dev will go ahead and create a /dev/lirc0 node. Now when lircd/mode2 opens this device, no data is available because the driver was never opened. Other case pointed by Sean Young, As rc device gets opened via the input interface. If the input device is never opened (e.g. embedded with no console) then the rc open is never called and lirc will not work either. So that's another case. lirc_dev seems to have no link with actual rc device w.r.t open/close. This patch adds rc_dev pointer to lirc_driver structure for cases like this, so that it can do the open/close of the real driver in accordance to lircd/mode2 open/close. Without this patch its impossible to open a rc device which has RC_TYPE_LIRC ad RC_MAP_LIRC set. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] media: rc: Add rc_open/close and use count to rc_devSrinivas Kandagatla1-0/+4
This patch adds user count to rc_dev structure, the reason to add this new member is to allow other code like lirc to open rc device directly. In the existing code, rc device is only opened by input subsystem which works ok if we have any input drivers to match. But in case like lirc where there will be no input driver, rc device will be never opened. Having this user count variable will be usefull to allow rc device to be opened from code other than rc-main. This patch also adds rc_open and rc_close functions for other drivers like lirc to open and close rc devices. This functions safely increment and decrement the user count. Other driver wanting to open rc device should call rc_open and rc_close, rather than directly modifying the rc_dev structure. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-11-18upstream: [media] media: i2c: adv7343: make the platform data members as arrayLad, Prabhakar1-16/+4
This patch makes the platform data members as array wherever possible, so as this makes easier while collecting the data in DT case and read the entire array at once. This patch also makes appropriate changes to board-da850-evm.c Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 14:33:37 +0000