summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2010-10-29misc: Add ab8500 pwm driverArun Murthy4-1/+190
This patch adds a Pulse Width Modulation driver for Analog Baseband Chip AB8500. Signed-off-by: Arun Murthy <arun.murthy@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Align ab8500 with the abx500 interfaceMattias Wallin4-203/+271
This patch makes the ab8500 mixed signal chip expose the same interface for register access as the ab3100, ab3550 and ab5500 chip. The ab8500_read() and ab8500_write() is removed and replaced with abx500_get_register_interruptible() and abx500_set_register_interruptible(). Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29gpio: Handle stmpe-gpio platform data with no gpio baseVirupax Sadashivpetimath1-2/+0
This patch removes the requirement that gpio base be supplied in platform data. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mmc: Allow 2 byte requests in 4-bit mode for tmio_mmcYusuke Goda2-5/+18
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit mode if the hardware supports it. Tested with the SDHI hardware block included in sh7724. Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Signed-off-by: Matt Fleming <matt@console-pimps.org> Acked-by: Magnus Damm <damm@opensource.se> Tested-by: Arnd Hannemann <arnd@arndnet.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mmc: Allow the platform to specify the sh_mmcif get_cd handlerArnd Hannemann1-0/+12
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not directly connected to the sh_mmcif controller, so that polling needs to be used. To overcome the overhead induced by querying the controller on each poll cycle, card detection can be handled in the platform code more efficiently. This patch exposes a get_cd hook for that purpose. Signed-off-by: Arnd Hannemann <arnd@arndnet.de> Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Allow the platform to specify the sh_mobile_sdhi get_cd handlerArnd Hannemann1-0/+13
On some platforms (e.g. AP4EVB) the card detect pin of a slot is not directly connected to the sdhi hardware, so that polling needs to be used with tmio_mmc and card detection is handled in the platform code. This patch allows to set tmio_mmc capabilities (to pass the MMC_CAP_NEEDS_POLL flag) and exposes a get_cd hook for that purpose. Signed-off-by: Arnd Hannemann <arnd@arndnet.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mmc: Allow the tmio_mmc mfd driver to specify get_cd handlerArnd Hannemann1-0/+13
Some controllers, supported by the tmio_mmc driver do not have the card detect pin of a slot connected, so that polling needs to be used and card detection is handled by other means. This patch exposes a get_cd hook for that purpose. Signed-off-by: Arnd Hannemann <arnd@arndnet.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29rtc: Add MAX8998 rtc driverJoonyoung Shim4-1/+334
This adds support for the RTC provided by the Maxim 8998 chip. This driver was tested on a GONI board by using the rtc-test application from the Documentation/rtc.txt. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Add MAX8998 interrupts supportJoonyoung Shim4-3/+281
Use genirq and provide seperated file for interrupts support. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Use i2c_client as an argument on MAX8998 i2c routinesJoonyoung Shim2-21/+25
The MAX8998 chip have regulator and rtc features. The i2c slave address of regulator and rtc is different, so needs each i2c client on i2c operation functions. Also, this patch exports i2c operation functions instead of callback to make easy to read. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Remove redundant code to get htc_pasic3 irqAxel Lin1-7/+0
There is no reason to get irq twice. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Fix tps6586x_add_subdevs error pathAxel Lin1-1/+7
1. return -ENOMEM if platform_device_alloc() fail. 2. call platform_device_put() if platform_device_add() fail. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Fix pcap_add_subdev error pathAxel Lin1-1/+9
1. return -ENOMEM if platform_device_alloc() fail. 2. call platform_device_put() if platform_device_add() fail. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Fix da903x_add_subdevs error pathAxel Lin1-1/+7
This patch fixes da903x_add_subdevs error path: 1. return -ENOMEM if platform_device_alloc() fail. 2. call platform_device_put() if platform_device_add() fail. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Eric Miao <eric.y.miao@gmail.com> Acked-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Add codec resource into 88pm860x driverHaojian Zhuang1-0/+44
Add codec IRQ resources that are used in 88pm860x codec driver. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Free tps6586x allocated resources when unload the moduleAxel Lin1-0/+13
For the resources allocated in tps6586x_i2c_probe(), we need to free it in tps6586x_i2c_remove(). Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29usb: otg: twl4030-usb: switch over to defines in twl.hFelipe Balbi1-4/+9
use the new definitions on twl header for code consistency. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Switch twl4030-power over to defines in twl.hFelipe Balbi1-14/+16
use the new definitions on twl header for code consistency. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Switch twl-core over to defines in twl.hFelipe Balbi1-12/+9
use the new definitions on twl header for code consistency. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: LP3974 PMIC supportKyungmin Park2-7/+9
LP3974 PMIC support. It has same functionality as max8998. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29gpio: Add bitmask to block requests to unavailable stmpe GPIOsWolfram Sang1-0/+5
GPIOs on these controller are multi-functional. If you decided to use some of them e.g. as input channels for the ADC, you surely don't want those pins to be reassigned as simple GPIOs (which may be triggered even from userspace via 'export'). Same for the touchscreen controller pins. Since knowledge about the hardware is needed to decide which GPIOs to reserve, let this bitmask be inside platform_data and provide some defines to assist potential users. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Rabin Vincent <rabin.vincent@stericsson.com> Cc: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Switch AB3100 to use MFD cellsLinus Walleij2-61/+69
This switches the AB3100 core driver to using MFD cells for subdevices instead of spawning common platform devices. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Move AB3100 to __devinitLinus Walleij1-7/+7
Since there is no discardable probe() function in the I2C device framework, let's just tag it __devinit and take the footprint hit rather than seeing the compilation warnings every day. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29gpiolib: Hook up WM8994 gpio_to_irq()Mark Brown1-0/+1
Not sure where this went. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-29mfd: Move PCF50633 IRQ protoypes where the definitions can see themMark Brown1-7/+0
Fixed warnings about unprototyped global functions. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-10-28watchdog: add support for Broadcom BCM63xx built-in watchdogFlorian Fainelli3-0/+361
This patch adds support for the Broadcom BCM63xx SoC built-in watchdog, it uses one of the BCM63xx hardware timer id. Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28watchdog: f71808e_wdt: add support for the F71889FGGiel van Schijndel2-3/+11
Signed-off-by: Giel van Schijndel <me@mortis.eu> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28watchdog: MachZ: fix debug macroNicolas Kaiser1-1/+1
Fix debug macro line wrapping. Signed-off-by: Nicolas Kaiser <nikai@nikai.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28watchdog: it8712f_wdt: Add module parameter for alternative reset sourcesTimo Juhani Lindfors1-2/+11
On iEi PCISA-9652-R10 (BIOS version 1.5) single board computer reads from the game port do not seem to reset the watchdog timer. This patch adds a module parameter wdt_config_reg to specify alternative reset sources. At least WDT_RESET_KBD has been tested, even just running while true; do setleds -L +scroll sleep 1 setleds -L -scroll sleep 1 done is enough to keep the watchdog happy. Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28 watchdog: it8712f_wdt: Add comments for config/control register namesTimo Juhani Lindfors1-6/+6
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28watchdog: it87_wdt: Add support for watchdogs with 8b timersOndrej Zajicek2-28/+63
This patch adds support for watchdogs with 8b timers, like ones in IT8702F and older revisions of IT8712F Super IO chip, to it87_wdt driver. This patch should be used after the patch 'it87_wdt: Add support for IT8720F watchdog'. Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2010-10-28regulator: max8952 - fix max8952_set_voltageAxel Lin1-1/+1
In current implementation, vid is declared as u8, then "vid == -1" is always false, and "vid >= 0" is always true. Thus change it to s8. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28regulator: max8952 - fix max8952_pmic_probe error pathAxel Lin1-2/+8
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28regulator: fix build when CONFIG_REGULATOR_DUMMY=nAnand Gadiyar1-4/+0
Commit f03f91826 (regulator: Add option for machine drivers to enable the dummy regulator) in the regulators tree seems to have introduced the following build break when CONFIG_REGULATOR_DUMMY is disabled. Fix this. CC drivers/regulator/dummy.o drivers/regulator/dummy.c:41: error: redefinition of 'regulator_dummy_init' drivers/regulator/dummy.h:28: note: previous definition of 'regulator_dummy_init' was here make[2]: *** [drivers/regulator/dummy.o] Error 1 make[1]: *** [drivers/regulator] Error 2 make: *** [drivers] Error 2 Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28regulator: avoid deadlock when disabling regulator with supplyJeffrey Carlyle1-9/+26
I have a regulator A that sets regulator B as its supply. When I call set_supply to add B as the supply for A, regulator A gets added to the supply_list for regulator B. When I call regulator_disable(A), I end up with a call chain like this: regulator_disable(A) > mutex_lock(A) > _regulator_disable(A) >> _regulator_disable(B) >>> _notifier_call_chain(B) >>>> mutex_lock(A) Which results in dead lock since we are trying to acquire the mutex lock for regulator A which we already hold. This patch addresses this issue by moving the call to disable regulator B outside of the lock aquired inside the initial call to regulator_disable. This change also addresses the issue of not acquiring the mutex for regulator B before calling _regulator_disable(B). Signed-off-by: Jeffrey Carlyle <jeff.carlyle@motorola.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28regulator: Add option for machine drivers to enable the dummy regulatorMark Brown2-2/+23
Allow machine drivers to explicitly enable the use of the dummy regulator, enabling simpler support for systems with only a few specific supplies visible to software. It is strongly recommended that this is not used on systems with substantial software control over their PMICs, for maximum functionality constrints should be as fully specified as possible. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28Regulator: lp3972 cleanupAxel Lin1-7/+18
This patch includes below fixes based on Mark's comment. - Return actual error if i2c_smbus_read_byte_data() fail - Add spaces around bitwise AND operator(&) to improve readability - Add comment to explain why we need to update voltage change control register for LDO1 and LDO5 - Logging the value for diagnostics if chip reported incorrect voltage value - Add __devinit annotation for setup_regulators() - Show system control register1 value if the value is mismatched - Logging the value for diagnostics if failed to detect device Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28Regulator: LP3972 PMIC regulator driverAxel Lin3-0/+657
This patch adds regulator drivers for National Semiconductors LP3972 PMIC. This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3972 PMIC controller uses I2C interface. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28MAX8952 PMIC Driver Initial ReleaseMyungJoo Ham3-0/+369
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV with DVS support. In this initial release, users can set voltages for four DVS modes, RAMP delay values, and SYNC frequency. Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID is not supported in this release. If GPIO of EN is not valid in platform data, the driver assumes that it is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down VID0 and VID1 to fix DVS mode as 0 and disables DVS support. We assume that V_OUT is capable to provide every voltage from 770mV to 1.40V in 10mV steps although the data sheet has some ambiguity on it. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> -- v2: - Style correction - Can accept platform_data with invalid GPIOs - Removed unnecessary features - Improved error handling Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28watchdog: it87_wdt: Add support for IT8720F watchdogOndrej Zajicek2-10/+16
This simple patch adds support for a watchdog in IT8720F Super IO chip to it87_wdt driver. Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2010-10-28watchdog: Use static const char * const where possibleJoe Perches1-1/+1
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28watchdog: iTCO_wdt: Cleanup warning messagesPrarit Bhargava1-9/+12
The current iTCO_wdt driver warnings are confusing. Currently when the device driver returns an error the console contains: iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware iTCO_wdt: No card detected After the patch, iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 iTCO_wdt: failed to reset NO_REBOOT flag, device disabled by hardware/BIOS Clean this up and use the word "device" to describe the device. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28watchdog: iTCO_wdt: TCO Watchdog patch for Intel Patsburg DeviceIDsSeth Heasley1-0/+3
This patch adds the Intel Patsburg (PCH) DeviceIDs for iTCO Watchdog. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2010-10-28Merge branch 'hwmon-for-linus' of ↵Linus Torvalds21-504/+3165
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (68 commits) hwmon: (it87) Add support for the IT8721F/IT8758E hwmon: (it87) Move conversion functions hwmon: Remove many EXPERIMENTAL flags hwmon: (lm85) Add support for ADT7468 high-frequency PWM mode hwmon: (lm85) Document the ADT7468 as supported hwmon: (lm85) Fix ADT7468 frequency table hwmon: I2C addresses are constant Move ams driver to macintosh hwmon: (pcf8591) Don't attempt to detect devices hwmon: (pcf8591) Register as a hwmon device hwmon: (w83795) Use standard attributes for chassis intrusion hwmon: (w83795) Exclude fan control feature by default hwmon: (w83795) Add myself as co-author and maintainer hwmon: (w83795) More style cleanups hwmon: (w83795) Fix LSB reading of voltage limits hwmon: (w83795) Use dev_get_drvdata() where possible hwmon: (w83795) Delay reading pwm config registers hwmon: (w83795) Delay reading limit registers hwmon: (w83795) Move register reads to dedicated functions hwmon: (w83795) Pack similar register reads ...
2010-10-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6Linus Torvalds1349-148410/+430571
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (841 commits) Staging: brcm80211: fix usage of roundup in structures Staging: bcm: fix up network device reference counting Staging: keucr: fix up US_ macro change staging: brcm80211: brcmfmac: Removed codeversion from firmware filenames. staging: brcm80211: Remove unnecessary header files. staging: brcm80211: Remove unnecessary includes from bcmutils.c staging: brcm80211: Removed unnecessary pktsetprio() function. Staging: brcm80211: remove typedefs.h Staging: brcm80211: remove uintptr typedef usage Staging: hv: remove struct vmbus_channel_interface Staging: hv: remove Open from struct vmbus_channel_interface Staging: hv: storvsc: call vmbus_open directly Staging: hv: netvsc: call vmbus_open directly Staging: hv: channel: export vmbus_open to modules Staging: hv: remove Close from struct vmbus_channel_interface Staging: hv: netvsc: call vmbus_close directly Staging: hv: storvsc: call vmbus_close directly Staging: hv: channel: export vmbus_close to modules Staging: hv: remove SendPacket from struct vmbus_channel_interface Staging: hv: storvsc: call vmbus_sendpacket directly ... Fix up conflicts in drivers/staging/cx25821/cx25821-audio-upstream.c drivers/staging/cx25821/cx25821-audio.h due to warring whitespace cleanups (neither of which were all that great)
2010-10-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds10-214/+165
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (32 commits) sh: intc: switch irq_desc iteration to new active IRQ iterator. sh: fix up cpu hotplug IRQ migration for irq_data changes. sh: oprofile: Make sure the backtrace op is available for timer-fallback. sh64: oprofile: Fix up kernel stack pointer size mismatch. sh: oprofile: Fix up and extend op_name_from_perf_id(). sh: lockless get_user_pages_fast() sh64: _PAGE_SPECIAL support. sound: sh: ctrl_in/outX to __raw_read/writeX conversion. sh: disable deprecated genirq support. sh: update show_interrupts() for irq_data chip lookup. sh: intc: irq_data conversion. sh64: irq_data conversion. sh64: update for IRQ flag handling naming changes. rtc: rtc-rs5c313: ctrl_in/outX to __raw_read/writeX conversion. sh: mach-se: irq_data conversion. input: hp680_ts_input: ctrl_in/outX to __raw_read/writeX conversion. input: jornada680_kbd: ctrl_in/outX to __raw_read/writeX conversion. sh: hd64461: irq_data conversion. sh: mach-x3proto: irq_data conversion. sh: mach-systemh: irq_data conversion. ...
2010-10-28Merge branch 'linux-next' of ↵Linus Torvalds17-29/+213
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits) x86: allocate space within a region top-down x86: update iomem_resource end based on CPU physical address capabilities x86/PCI: allocate space from the end of a region, not the beginning PCI: allocate bus resources from the top down resources: support allocating space within a region from the top down resources: handle overflow when aligning start of available area resources: ensure callback doesn't allocate outside available space resources: factor out resource_clip() to simplify find_resource() resources: add a default alignf to simplify find_resource() x86/PCI: MMCONFIG: fix region end calculation PCI: Add support for polling PME state on suspended legacy PCI devices PCI: Export some PCI PM functionality PCI: fix message typo PCI: log vendor/device ID always PCI: update Intel chipset names and defines PCI: use new ccflags variable in Makefile PCI: add PCI_MSIX_TABLE/PBA defines PCI: add PCI vendor id for STmicroelectronics x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs PCI: OLPC: Only enable PCI configuration type override on XO-1 ...
2010-10-28hwmon: (it87) Add support for the IT8721F/IT8758EJean Delvare2-24/+96
Add support for the IT8721F/IT8758E. These new chips differ from the older IT87xxF chips in the following ways: * ADC LSB is 12 mV instead of 16 mV. * PWM values are 8-bit instead of 7-bit. There are other minor changes we don't have to care about in the driver. Another change is that we will handle internal voltage scaling in the driver instead of delegating the work to user-space. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (it87) Move conversion functionsJean Delvare1-50/+52
Move conversion functions until after structure defintions. This is needed for future changes which make use of the structures in the conversion funtcions. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: Remove many EXPERIMENTAL flagsJean Delvare1-16/+12
Remove the dependency on EXPERIMENTAL for all drivers which are in the kernel tree for a long time, are known to work properly and for which we have documentation. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Corentin Labbe <corentin.labbe@geomatys.fr> Cc: Riku Voipio <riku.voipio@iki.fi> Cc: Juerg Haefliger <juergh@gmail.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 04:20:03 +0000