Age | Commit message (Collapse) | Author | Files | Lines |
|
Enable support for hdmi for exynos5420 hdmiphy. Add
compatible string in the of_match table. Also added
hdmiphy configuration values for exynos5420.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch does the following in exynos5_i2c_message_start() function
1. Fixes an assignment
As, "i2c_auto_conf" is initialized to '0' at the beginning of the
function and HSI2C_READ_WRITE is defined as (1u << 16)
Using "|=" for the first assignment is more readable.
2. Removes an extra line
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch removes an extra read of FIFO_STATUS register in the interrrupt
service routine. Which is read again before the actual use.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The original code for the exynos i2c controller registered for the
"noirq" variants. However during review feedback it was moved to
SIMPLE_DEV_PM_OPS without anyone noticing that it meant we were no
longer actually "noirq" (despite functions named
exynos5_i2c_suspend_noirq and exynos5_i2c_resume_noirq).
i2c controllers that might have wakeup sources on them seem to need to
resume at noirq time so that the individual drivers can actually read
the i2c bus to handle their wakeup.
NOTE: I took the original review feedback from Wolfram and added
poweroff, thaw, freeze, restore.
This patch has only been compile-tested since I don't have all the
patches needed to make my machine using this i2c driver actually
suspend/resume.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. For example,
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Remove unnecessary cast of void pointer, because 'algo_data' of
'struct i2c_adapter' is a void pointer. Casting the void pointer
is redundant. The conversion from void pointer to any other
pointer type is guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
warning: 'exynos5_i2c_suspend_noirq' defined but not used [-Wunused-function]
warning: 'exynos5_i2c_resume_noirq' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
clk_disable_unprepare in remove causes an imbalance and hence gives
the below crash on module remove. While at it also remove some
duplicate code from probe.
/ $ rmmod i2c-exynos5
[ 6.996374] ------------[ cut here ]------------
[ 6.999523] WARNING: CPU: 2 PID: 1137 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
[ 7.007403] Modules linked in: i2c_exynos5(-)
[ 7.011747] CPU: 2 PID: 1137 Comm: rmmod Not tainted 3.12.0-next-20131105-00083-g16f4799-dirty #21
[ 7.020696] [<c0014e0c>] (unwind_backtrace+0x0/0xf4) from [<c0011784>] (show_stack+0x10/0x14)
[ 7.029190] [<c0011784>] (show_stack+0x10/0x14) from [<c037acd4>] (dump_stack+0x7c/0xb0)
[ 7.037255] [<c037acd4>] (dump_stack+0x7c/0xb0) from [<c001e0ac>] (warn_slowpath_common+0x6c/0x88)
[ 7.046190] [<c001e0ac>] (warn_slowpath_common+0x6c/0x88) from [<c001e164>] (warn_slowpath_null+0x1c/0x24)
[ 7.055818] [<c001e164>] (warn_slowpath_null+0x1c/0x24) from [<c02dcde4>] (clk_disable+0x18/0x24)
[ 7.064670] [<c02dcde4>] (clk_disable+0x18/0x24) from [<bf0002d4>] (exynos5_i2c_remove+0x1c/0x34 [i2c_exynos5])
[ 7.074736] [<bf0002d4>] (exynos5_i2c_remove+0x1c/0x34 [i2c_exynos5]) from [<c02274a8>] (__device_release_driver+0x58/0xb0)
[ 7.085836] [<c02274a8>] (__device_release_driver+0x58/0xb0) from [<c0227b88>] (driver_detach+0xac/0xb0)
[ 7.095291] [<c0227b88>] (driver_detach+0xac/0xb0) from [<c02271c0>] (bus_remove_driver+0x4c/0xa0)
[ 7.104227] [<c02271c0>] (bus_remove_driver+0x4c/0xa0) from [<c00725dc>] (SyS_delete_module+0x124/0x194)
[ 7.113682] [<c00725dc>] (SyS_delete_module+0x124/0x194) from [<c000e2e0>] (ret_fast_syscall+0x0/0x30)
[ 7.122957] ---[ end trace 23bb6e4e0bf52196 ]---
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Adds support for High Speed I2C driver found in Exynos5 and
later SoCs from Samsung.
Driver only supports Device Tree method.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@google.com>
[wsa: rebased to v3.12-rc4 (no of_i2c.h anymore)]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Previous SoCs have hdmi phys which are accessible through
dedicated i2c lines. Newer SoCs have Apb mapped hdmi phys.
Hdmi driver is modified to support apb mapped phys.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Exynos5420 is octa-core SoC from Samsung. Hence extend exynos-mct clocksource
driver to support 8 local interrupts.
Also extend dts entries for 8 interrupts.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
registration
Replace the (setup/remove)_irq calls for local timer registration with
(request/free)_irq calls. This generalizes the local timer registration API.
Suggested by Mark Rutland.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
All EXYNOS4/5 SoCs share a common driver data in the samsung serial
driver. Hence, let the driver data inclusion be based on ARCH_EXYNOS
instead of SOC specific definition.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add Samsung EXYNOS5420 SoC specific data to enable pinctrl
support for all platforms based on EXYNOS5420.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by : Sunil Joshi <joshi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Current platform specific private data initialization call
dw_mci_exynos_priv_init() can be used to do platform specific
initialization of SMU and others in future. So the drv_data->init
call has moved to dw_mci_probe().
Change-Id: I02dbf3360a283d7a25e171e1f97832c01837d5d1
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Exynos5420 Mobile Storage Host controller has Security Management
Unit (SMU) for channel 0 and channel 1 (mainly for eMMC).
This time, SMU configuration is set for non-encryption mode.
Change-Id: I405651fd5aee1c572d39e05400a048bf724be4ad
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Currently platform specific private data initialization is done by
dw_mci_exynos_priv_init and dw_mci_exynos_parse_dt. As we already have
separate platform specific device tree parser dw_mci_exynos_parse_dt,
move the dw_mci_exynos_priv_init code to dw_mci_exynos_parse_dt.
We can use the dw_mci_exynos_priv_init to do some actual platform
specific initialization of SMU and etc.
Change-Id: Iad20178598423b69d029e33ee1e3d77a76fbd888
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The Exynos5420 has a DWMMC controller which is different from prior
versions.This patch adds a new compatible string for Exynos5420.
Change-Id: I9191ebc65d2e308a43980a81d4a2b0c48c771ca0
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Replace irq_domain_add_simple with "irq_domain_add_linear" in order to use
linear irq domain, and to remove hardcoded irq_base_value.
Change-Id: I2b8235d77f6545ac24b41d3bce8f24c60d829a39
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The ssp_data pointer is allocated with devm_kzalloc, so freeing it
is not necessary.
Change-Id: Idd26ba71e9c343d61e7b5aa01b21a2f2c3ae9b00
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This module has a resource free bug so this patch disables
dmabuf sync module until the bug is fixed.
Change-Id: Ic84c88e3d5dbead1c25bf4b238b8ef5f51045099
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The memcpy with string source and size larger than string length
causes data overflow. So this patch replaces memcpy to strncpy to
fix data overflow.
Change-Id: Ibc326bdf0a1235c67013576ab9d8f170e8711344
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
After freeing pin from regulator_ena_gpio_free, loop can access
the pin. So this patch fixes not to access pin after freeing.
Change-Id: I690860751e45b1513fb9171bba1c0bb7e89c0446
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
Without sentinel, of_match_node() to array causes out-of-bound
memory access. So this patch adds sentinel into array.
Change-Id: Icfe3d8c2fdb0faa006f413e7c080b6d713eab08c
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
User can send wrong message size, so before setting message value,
the size should be checked to prevent buffer overflow.
Change-Id: Ia3ebdbd45b357054b6fad05c7f251a0b770172db
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
The data in config_fw has header, data blocks and end block. The
data count in the config_fw is the number of data blocks except
end block. Without considering end block, this causes buffer
overflow. So this patch fixes allocation size considering end block.
Change-Id: I053e251a21ba8befb03a1db233e4e2d9dbf1b795
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
As reported by smatch:
drivers/media/dvb-core/dmxdev.c:1091 dvb_demux_poll() warn: variable dereferenced before check 'dmxdevfilter' (see line 1088)
This was introduced by changeset d102cac8097c.
We need to test before using it.
Change-Id: I4e51d508c466b915338bd0a88a7afb49f4dbeb4d
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
|
|
Some formats are not supported in encoding or decoding
mode for given type of buffer (e.g. V4L2_PIX_FMT_JPEG
is supported on output buffer only while in decoding
mode). Make S_FMT failing if not suitable format
is found.
Change-Id: I35c94e38b1b11e2c379f4b2e1f61eedab2bc0a9d
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: I5c074dce7e89cbe8ba93872f4edce97431e864cc
|
|
unsigned comparison
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: Ia9ce7abb542b7dd82a9bc9b23e94728b57f95e59
|
|
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: I26aec009f6b61c077c6de1a96cca7a5132851dbf
|
|
Cancel fence free worker if there is no any task or dma device.
And do not drop a reference of dmabuf at fence free worker,
which is over-dropping.
Change-Id: Ib7378d4efc68a8f7ee7a161296f6a9c0e78f77a7
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch use strcpy() for assign input device name.
Change-Id: I2d363de2b0fe88d771ed71a861f7880a73dc6dac
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
|
|
Add support for FIMC ISP and SCALERC v4l2 controls
Change-Id: I360597cbaed60a24f3184df3c5617f868fd02749
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
|
|
As the driver maintaines separate buffer lists per each
video device which are beyond control of v4l2/vb2
framework, those lists should be properly handled
and cleared once the buffers are no longer
available. The changes introduced allow controlling
state of each queued buffer and removing it from
internal buffer lists when needed.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Change-Id: I4dea7df3910d6836edee1387c5a1147649043b81
|
|
The changes introduced provide support for FIMC-IS
subsystem avalilable on Exynos3250.
They cover the differences in both: the hardware itself
as well as the subtle discrepancies between the firmwares
controlling the FIMC IS on both SoCs.
Regarding the above mentioned firmware variations:
the initial driver has been extended with a simplified
interface handling those variations thus living the core
driver independent of the actual firmware version.
Missing code paths have been added to cover handling some of
the most probable failures/errors.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Change-Id: Ie07312013a6a0ee14b88803360f0832d0ad4038d
|
|
- Code cleanup for Exynos5/3 media device driver
- Proper locking for vb2 buffers for both FIMC ISP
and FIMC SCC v4l2 subdevices
- Improved handling VIDIOC_REQBUFS ioctl
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Change-Id: If7ee3f7861678169c2c0f0fc217d3507b3e3d4fc
|
|
This patch adds notifying v4l2 subdevs upon capture
frame end event.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Change-Id: Id3e81b4692a6f2cfc91ffde7050a3ae6db719971
|
|
In case of Exynos3250 only gate clock is required
thus all the remaining mipi-csis clocks are considered
as optional.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Change-Id: Ibadffe49739add39f156737cbb723b24a5dd4ff5
|
|
Particular interrupt source mask should specify
each and every possible event/error reflecting the
s5pcsis_events table content.
Change-Id: I3149364cf219d8ec2c13297a8890537585ae77ca
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
|
|
Change-Id: I7e1c466c6622b39c2999e2245c7815e6517dd157
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
There is no sclk_bayer clock on exynos3250.
Some flag at the variant data could be added later to handle
properly error from clk calls.
Change-Id: I249169e1a7c451db6805dee7d01dd95816f329e0
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Change platform sub-devices registration method so the driver
can support exynos3250 DT binding, i.e. initialize when fimc-is
is the complex root node, not "camera".
This also merges exynos5-fimc-is and exynos-mdevice into single
kernel module called exynos-iss.ko.
Change-Id: Ie340fd7a3e1f7b5dba2c71963c920f324fab4e5a
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This driver is for the FIMC-IS IP available in Samsung Exynos5
SoC onwards.
exynos5-fimc-is: Add common driver header files
This patch adds all the common header files used by the fimc-is
driver. It includes the commands for interfacing with the firmware
and error codes from IS firmware, metadata and command parameter
definitions.
exynos5-fimc-is: Add register definition and context header
This patch adds the register definition file for the fimc-is driver
and also the header file containing the main context for the driver.
exynos5-fimc-is: Add isp subdev
fimc-is driver takes video data input from the ISP video node
which is added in this patch. This node accepts Bayer input
buffers which is given from the IS sensors.
exynos5-fimc-is: Add scaler subdev
FIMC-IS has two hardware scalers named as scaler-codec and
scaler-preview. This patch adds the common code handling the
video nodes and subdevs of both the scalers.
exynos5-fimc-is: Add sensor interface
Some sensors to be used with fimc-is are exclusively controlled
by the fimc-is firmware. This minimal sensor driver provides
the required info for the firmware to configure the sensors
sitting on I2C bus.
exynos5-fimc-is: Add the hardware pipeline control
This patch adds the crucial hardware pipeline control for the
fimc-is driver. All the subdev nodes will call this pipeline
interfaces to reach the hardware. Responsibilities of this module
involves configuring and maintaining the hardware pipeline involving
multiple sub-ips like ISP, DRC, Scalers, ODC, 3DNR, FD etc.
exynos5-fimc-is: Add the hardware interface module
The hardware interface module finally sends the commands to the
FIMC-IS firmware and runs the interrupt handler for getting the
responses.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kilyeon Im <kilyeon.im@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
exynos5-is: Add Kconfig and Makefile
Adds Kconfig and Makefile for exynos5-is driver files.
[b.michalska@samsung.com: Implementation adjusted
to current version of V4L2 framework:
- updated prototype for stop_streaming v4l2 capture ops
- vb2_queue struct's field tiemstamp_type updated
to timestamp_flags]
Change-Id: I066a86151048b4b5871bd3732773b87219f04fd1
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This patch adds a top level media device driver for the Exynos5 SoC series
camera subsystem. The driver currently supports processing pipelines
involving following IP blocks:
* MIPI-CSIS
MIPI CSI-2 bus front-end to the FIMC-LITE, image sensors with MIPI CSI-2
bus should be linked with FIMC-LITE through this sub-device.
* FIMC-LITE
Supports capture interface from device (Sensor, MIPI-CSIS) to memory.
Supports interconnection (through internal data FIFO links) between
devices like MIPI-CSIS and FIMC-IS.
* FIMC-IS
Camera ISP with multiple image processing and peripheral devices like
I2C or SPI bus controllers.
The G-Scaler IP is not yet supported.
The media device creates two kinds of pipelines for connecting the above
mentioned IP blocks.
The pipeline0 contains Sensor, MIPI-CSIS and FIMC-LITE devices and allows
to capture image data from external sensor to memory.
Pipeline1 uses FIMC-IS components for image processing operations on the
captured raw image data and provides scaled YUV image data at its output.
Pipeline0
+--------+ +-----------+ +-----------+ +--------+
| Sensor | --> | MIPI-CSIS | --> | FIMC-LITE | --> | Memory |
+--------+ +-----------+ +-----------+ +--------+
Pipeline1
+--------+ +---------+ +-----------+ +-----------+
| Memory | --> | ISP | --> | SCC | --> | SCP |
+--------+ +---------+ +-----------+ +-----------+
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[s.nawrocki@samsung.com: improved the commit description,
removed inclusion of nonexistent <linux/of_i2c.h> header]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Change-Id: Icccb5c45cebe4b46790a1bdce436c00090924d7a
|
|
Adapt current implementation to cover differences
in MIPI CSIS registers layout.
Change-Id: I092394f722c019dbb80ac833dc41256566388e8e
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
|
|
Add support for enabling/disabling local output
path along with disabling interrupts upon capture
being stopped.
Change-Id: I8ed2e100138f567dbd10c2eb5083b12110a3c799
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
|