summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2011-06-22ssb: add __devinit to some functionsHauke Mehrtens6-32/+36
Two functions in ssb are using register_pci_controller() which is __devinit. The functions ssb_pcicore_init_hostmode() and ssb_gige_probe() should also be __devinit. This fixes the following warning: WARNING: vmlinux.o(.text+0x2727b8): Section mismatch in reference from the function ssb_pcicore_init_hostmode() to the function .devinit.text:register_pci_controller() The function ssb_pcicore_init_hostmode() references the function __devinit register_pci_controller(). This is often because ssb_pcicore_init_hostmode lacks a __devinit annotation or the annotation of register_pci_controller is wrong. WARNING: vmlinux.o(.text+0x273398): Section mismatch in reference from the function ssb_gige_probe() to the function .devinit.text:register_pci_controller() The function ssb_gige_probe() references the function __devinit register_pci_controller(). This is often because ssb_gige_probe lacks a __devinit annotation or the annotation of register_pci_controller is wrong. Reported-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: enable support for AR9330Gabor Juhos1-0/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add external_reset callback to ath9k_platfom_data for AR9330Gabor Juhos3-0/+37
The patch adds a callback to ath9k_platform_data. If the callback is provided by the platform code, then it can be used to hard reset the WMAC device. The callback is required for doing a hard reset of the AR9330 chips to get them working again after a hang. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: configure internal regulator for AR9330Gabor Juhos1-5/+20
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: configure diversity based on eeprom contents for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: fix few register offsets for AR9330Gabor Juhos1-2/+2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: set diversity group for AR9330Gabor Juhos1-1/+4
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add fast_div_bias configuration for diversity group 1Gabor Juhos1-0/+83
The patch adds the missing configuration code for diversity group 1. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: remove superfluous parenthesesGabor Juhos1-32/+30
Also remove two empty lines. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: fix antenna diversity configuration for non AR9485 chipsGabor Juhos1-2/+8
The current values must be used only on AR9485 chips. Other chips requires different values. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add a missing case statement to ath_ant_div_comb_alt_checkGabor Juhos1-0/+1
The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2 however that value is not used in 'ath_ant_div_comb_alt_check'. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: use correct max_streams for AR9330Gabor Juhos1-1/+1
The AR9330 is a single stream chip. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: enable antenna diversity for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: set NF limits for AR9330Gabor Juhos2-1/+6
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: configure xpa bias level for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: use correct EEPROM base for AR9330Gabor Juhos1-0/+2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: enable tuning capacitance configuration for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: skip internal regulator configuration for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: enable TX/RX data byte swap for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: configure RF channel frequency for AR9330Gabor Juhos1-1/+13
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: fix channel frequency calculation for AR9340Gabor Juhos1-1/+1
A multiplication is missing from the current formula. Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: read spur frequency information from eeprom for AR9330Gabor Juhos1-2/+2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: don't enable LDPC for AR9330Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: use different BB watchdog timeout value for AR9330Gabor Juhos1-1/+4
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add AR9330 specific PLL initializationGabor Juhos1-1/+34
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: initialize rx gain table for AR9330Gabor Juhos1-2/+22
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: initialize tx gain table for AR9330Gabor Juhos1-4/+44
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: initialize mode registers for AR9330Gabor Juhos2-1/+112
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add AR9330 initvalsGabor Juhos2-0/+2227
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add platform device id for AR9330Gabor Juhos1-0/+4
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: add MAC revision detection for AR9330Gabor Juhos3-0/+11
The AR9330 1.0 and 1.1 are using the same revision, thus it is not possible to distinguish the two chips. The platform setup code can distinguish the chips based on the SoC revision. Add a callback function to ath9k_platform_data in order to allow getting the revision number from the platform code. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: define device id for AR9330Gabor Juhos1-0/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k: define mac version for AR9330Gabor Juhos2-1/+20
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22ath9k_hw: Fix calculation of PAPRD training power at 5GhzMohammed Shafi Shajakhan1-1/+17
higher the chainmask, lesser the power_delta to be added to the paprd_training_power Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22mwifiex: remove casts of void pointersAmitkumar Karwar13-177/+129
In some cases local pointers are used to cast void pointers passed to the function. Those unnecessary local pointers are also removed. This patch was inspired by Joe Perches' patch [PATCH net-next 1/2] wireless: Remove casts of void *; and the comments from Julian Calaby. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Cc: Joe Perches <joe@perches.com> Cc: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: detect stalled beacon interrupt fasterJussi Kivilinna1-1/+2
As USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS, beacon interrupt (CR_INTERRUPT) might be lost. Problem is that when device trigger CR_INTERRUPT it disables HW interrupt. Now if USB_INT_ID_REGS with CR_INTERRUPT gets lost, beacon interrupt stays disabled until beacon watchdog notices the stall. This happen very often on heavy TX. Improve watchdog to trigger earlier, after three missing beacon interrupts. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: don't let zd_mac_config_beacon() run too long from beacon ↵Jussi Kivilinna1-7/+12
interrupt handler zd_mac_config_beacon() has only limited time to set up beacon when called from beacon interrupt handler/worker. So do not let it retry acquiring beacon fifo semaphore in interrupt handler. Beacon fifo semaphore should not be locked by firmware anyway at this time, it's only locked when device is using/txing beacon. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: handle lost read-reg interruptsJussi Kivilinna2-21/+109
Device losses read-reg interrupts. By looking at usbmon it appears that USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS. This causes read command to timeout, usually under heavy TX. Fix by retrying read registers again if USB_INT_ID_RETRY_FAILED is received while waiting for USB_INT_ID_REGS. However USB_INT_ID_REGS is not always lost but is received after USB_INT_ID_RETRY_FAILED and is usually received by the retried read command. USB_INT_ID_REGS of the retry is then left unhandled and might be received by next read command. Handle this by ignoring previous USB_INT_ID_REGS that doesn't match current read command request. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: only update HW beacon if new beacon differs from currectJussi Kivilinna2-13/+64
Update HW beacon only when needed. This appears to make device work in AP-mode (dtim_period=1) somewhat more stable. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: make 'handle_rx_packet: invalid, small RX packet' message debug-onlyJussi Kivilinna1-2/+2
This message is should be debug-only as it tells almost nothing useful. It also happens very often and just floods logs. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: fix invalid signal values from deviceJussi Kivilinna2-2/+24
Driver uses IEEE80211_HW_SIGNAL_UNSPEC and so signal values reported to mac80211 should be in range 0..100. Sometimes device return out of range values. These out of range values can then trigger warning in cfg80211_inform_bss_frame. This patch adds checks to enforce range returned from driver to mac80211 be in 0..100 range. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: HT-PHY: calibrate radio after switching channelRafał Miłecki1-1/+7
After uploading radio values calibration goes in. In MMIO dump it is: radio_read(0x002b) -> 0x0008 radio_write(0x002b) <- 0x0008 radio_read(0x002e) -> 0x0004 radio_write(0x002e) <- 0x0000 radio_read(0x002e) -> 0x0000 radio_write(0x002e) <- 0x0004 radio_read(0x002b) -> 0x0008 radio_write(0x002b) <- 0x0009 To find masks and sets, MMIO hacks were used to fool closed driver. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22rt2x00: reset usb devices at probeStanislaw Gruszka1-0/+1
When module is reloaded, device may fail to work, with messages: [ 342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2. [ 342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2. [ 342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432. [ 342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2. [ 342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1. [ 342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432. [ 342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432. [ 342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432. [ 343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432. [ 343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432. [ 343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1. [ 343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1. Whereas replugging device make it functional. To solve that problem force reset device during probe. With patch messages are gone. Unfortunately device may sometimes still does not operate correctly after module reload (fail to receive data after associate), but such cases are rarer than without the patch. Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22rt2x00: fix possible memory corruption in case of invalid rxdesc.sizeStanislaw Gruszka1-0/+13
Sometimes rxdesc descriptor provided by hardware contains invalid (random) data. For example rxdesc.size can be bigger than actual size of the buffer. When this happen rt2x00crypto_rx_insert_iv() corrupt memory doing memmove outside of buffer boundaries. Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: N-PHY: move declarations of chantables functions to correct filesRafał Miłecki3-8/+10
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: N-PHY: update switching analog on/offRafał Miłecki1-4/+17
Specs were recently updated. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: HT-PHY: switch radio to requested channelRafał Miłecki2-1/+68
Switching channel happens after specific SHM write to B43_SHM_SH_CHAN. This is the way we found it in BCM4331 MMIO dumps. By comparing with N-PHY code we noticed there is routing used for SYN and TX/RX. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: HT-PHY: add place for implementing channel switchingRafał Miłecki1-2/+59
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: HT-PHY: define standard structs for channel switchingRafał Miłecki5-0/+59
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22b43: HT-PHY: enable radioRafał Miłecki1-0/+4
The trick was to find 0x810 PHY reg ops close to analog enabling code. To find out proper masks and sets, MMIO hacks were used. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 10:55:31 +0000