| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 984f1733fcee3fbc78d47e26c5096921c5d9946a upstream.
This patch fixes an out-of-bounds error in sd_read_cache_type(), found
by Google's AddressSanitizer tool. When the loop ends, we know that
"offset" lies beyond the end of the data in the buffer, so no Caching
mode page was found. In theory it may be present, but the buffer size
is limited to 512 bytes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9807b4d94911be4e4efb9a08481b24292a9edf8a upstream.
Right now the Makefile for the mpt3sas driver does not even allow the
driver to be built into the kernel. So fix that up, as there doesn't
seem to be any obvious reason why this shouldn't be done.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit 9504a923924d663e1953f872f0a828e6454a6cfc upstream.
The IO command size is 128 bytes for these new controllers as opposed to 64
for the old 8001 controller.
The Adaptec out-of-tree driver did this correctly. After comparing the two
this turned out to be the crucial difference.
So don't hardcode the IO command size, instead use pm8001_ha->iomb_size as
that is the correct value for both old and new controllers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Anand Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5944daa0a72316077435c18a6571e73ed338332 upstream.
We want ppc64 to be able to select between optimised assembly
checksum routines in big endian and the generic lib/checksum.c
routines in little endian.
The lpfc driver is forcing CONFIG_GENERIC_CSUM on which means
we are unable to make the decision to enable it in the arch
Kconfig. If the option exists it is always forced on.
This got introduced in 3.10 via commit 6a7252fdb0c3 ([SCSI] lpfc:
fix up Kconfig dependencies). I spoke to Randy about it and
the original issue was with CRC_T10DIF not being defined.
As such, remove the select of CONFIG_GENERIC_CSUM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b497ceb964a80ebada3b9b3cea4261409039e25a upstream.
ARM cannot handle udelay for more than 2 miliseconds, so we
should use mdelay instead for those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: GOTO Masanori <gotom@debian.or.jp>
Cc: YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa52aeea2725839bdd3dcce394486e9a043065e0 upstream.
vscsi->num_queues counts the number of request virtqueue which does not
include the control and event virtqueue. It is wrong to subtract
VIRTIO_SCSI_VQ_BASE from vscsi->num_queues.
This patch fixes the following panic.
(qemu) device_del scsi0
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffff8179b29f>] __virtscsi_set_affinity+0x6f/0x120
PGD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 659 Comm: kworker/0:1 Not tainted 3.11.0-rc2+ #1172
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kacpi_hotplug _handle_hotplug_event_func
task: ffff88007bee1cc0 ti: ffff88007bfe4000 task.ti: ffff88007bfe4000
RIP: 0010:[<ffffffff8179b29f>] [<ffffffff8179b29f>] __virtscsi_set_affinity+0x6f/0x120
RSP: 0018:ffff88007bfe5a38 EFLAGS: 00010202
RAX: 0000000000000010 RBX: ffff880077fd0d28 RCX: 0000000000000050
RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000000
RBP: ffff88007bfe5a58 R08: ffff880077f6ff00 R09: 0000000000000001
R10: ffffffff8143e673 R11: 0000000000000001 R12: 0000000000000001
R13: ffff880077fd0800 R14: 0000000000000000 R15: ffff88007bf489b0
FS: 0000000000000000(0000) GS:ffff88007ea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000020 CR3: 0000000079f8b000 CR4: 00000000000006f0
Stack:
ffff880077fd0d28 0000000000000000 ffff880077fd0800 0000000000000008
ffff88007bfe5a78 ffffffff8179b37d ffff88007bccc800 ffff88007bccc800
ffff88007bfe5a98 ffffffff8179b3b6 ffff88007bccc800 ffff880077fd0d28
Call Trace:
[<ffffffff8179b37d>] virtscsi_set_affinity+0x2d/0x40
[<ffffffff8179b3b6>] virtscsi_remove_vqs+0x26/0x50
[<ffffffff8179c7d2>] virtscsi_remove+0x82/0xa0
[<ffffffff814cb6b2>] virtio_dev_remove+0x22/0x70
[<ffffffff8167ca49>] __device_release_driver+0x69/0xd0
[<ffffffff8167cb9d>] device_release_driver+0x2d/0x40
[<ffffffff8167bb96>] bus_remove_device+0x116/0x150
[<ffffffff81679936>] device_del+0x126/0x1e0
[<ffffffff81679a06>] device_unregister+0x16/0x30
[<ffffffff814cb889>] unregister_virtio_device+0x19/0x30
[<ffffffff814cdad6>] virtio_pci_remove+0x36/0x80
[<ffffffff81464ae7>] pci_device_remove+0x37/0x70
[<ffffffff8167ca49>] __device_release_driver+0x69/0xd0
[<ffffffff8167cb9d>] device_release_driver+0x2d/0x40
[<ffffffff8167bb96>] bus_remove_device+0x116/0x150
[<ffffffff81679936>] device_del+0x126/0x1e0
[<ffffffff8145edfc>] pci_stop_bus_device+0x9c/0xb0
[<ffffffff8145f036>] pci_stop_and_remove_bus_device+0x16/0x30
[<ffffffff81474a9e>] acpiphp_disable_slot+0x8e/0x150
[<ffffffff81474f6a>] hotplug_event_func+0xba/0x1a0
[<ffffffff814906c8>] ? acpi_os_release_object+0xe/0x12
[<ffffffff81475911>] _handle_hotplug_event_func+0x31/0x70
[<ffffffff810b5333>] process_one_work+0x183/0x500
[<ffffffff810b66e2>] worker_thread+0x122/0x400
[<ffffffff810b65c0>] ? manage_workers+0x2d0/0x2d0
[<ffffffff810bc5de>] kthread+0xce/0xe0
[<ffffffff810bc510>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff81ca045c>] ret_from_fork+0x7c/0xb0
[<ffffffff810bc510>] ? kthread_freezable_should_stop+0x70/0x70
Code: 01 00 00 00 74 59 45 31 e4 83 bb c8 01 00 00 02 74 46 66 2e 0f 1f 84 00 00 00 00 00 49 63 c4 48 c1 e0 04 48 8b bc 0
3 10 02 00 00 <48> 8b 47 20 48 8b 80 d0 01 00 00 48 8b 40 50 48 85 c0 74 07 be
RIP [<ffffffff8179b29f>] __virtscsi_set_affinity+0x6f/0x120
RSP <ffff88007bfe5a38>
CR2: 0000000000000020
---[ end trace 99679331a3775f48 ]---
Signed-off-by: Asias He <asias@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6431f5d7c6025f8b007af06ea090de308f7e6881 upstream.
Problem: When Hardware IOMMU is on, megaraid_sas driver initialization fails
in kdump kernel with LSI MegaRAID controller(device id-0x73).
Actually this issue needs fix in firmware, but for firmware running in field,
this driver fix is proposed to resolve the issue. At firmware initialization
time, if firmware does not come to ready state, driver will reset the adapter
and retry for firmware transition to ready state unconditionally(not only
executed for kdump kernel).
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7562523e84ddc742fe1f9db8bd76b01acca89f6b upstream.
If a device has the skip_vpd_pages flag set we should simply fail the
scsi_get_vpd_page() call.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Stuart Foster <smf.linux@ntlworld.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3ccb1d7cf4c4549151876dd37c0944a682fd9e1 upstream.
This fixes a regression where Xyratex controllers and disks were lost by the
driver:
https://bugzilla.kernel.org/show_bug.cgi?id=59601
Reported-by: Jack Hill <jackhill@jackhill.us>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 085b513f97d8d799d28491239be4b451bcd8c2c5 upstream.
sd_prep_fn will allocate a larger CDB for the command via mempool_alloc
for devices using DIF type 2 protection. This CDB was being freed
in sd_done, which results in a kernel crash if the command is retried
due to a UNIT ATTENTION. This change moves the code to free the larger
CDB into sd_unprep_fn instead, which is invoked after the request is
complete.
It is no longer necessary to call scsi_print_command separately for
this case as the ->cmnd will no longer be NULL in the normal code path.
Also removed conditional test for DIF type 2 when freeing the larger
CDB because the protection_type could have been changed via sysfs while
the command was executing.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96f15f29038e58e1b0a96483e2b369ff446becf1 upstream.
This commit fixes a race condition in the isci driver abort task and SSP
device task management path. The race is caused when an I/O termination
in the SCU hardware is necessary because of an SSP target timeout condition,
and the check of the I/O end state races against the HW-termination-driven
end state. The failure of the race meant that no TMF was sent to the device
to clean-up the pending I/O.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Reviewed-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a6a731bd00ca90d0e250867c3b9c05b5ff0fa49 upstream.
commit 98cb7e44 ([SCSI] megaraid_sas: Sanity check user
supplied length before passing it to dma_alloc_coherent())
introduced a memory leak. Memory allocated for entries
following zero length SGL entries will not be freed.
Reference: http://bugs.debian.org/688198
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
non LUN 0 configured expander
commit b65cfedf4560af65305bd7b3b9f26c02c6fb3660 upstream.
With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created
then SCSI scan procedure calls target_alloc, slave_alloc call back functions
for LUN 0 and slave_destory() for same LUN 0.
In these kind of cases within slave_destroy, pointer to scsi_target in
_sas_device structure is set to NULL, following which when slave_alloc for LUN
1 is called then starget would not be set properly for this LUN. So,
scsi_target pointer pointing to NULL value would lead to a crash later in the
discovery procedure.
To solve this issue set the sas_device's scsi_target pointer to scsi_device's
scsi_target if it is NULL earlier in slave_alloc callback function.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE is not returned
commit 14be49ac965ebd3f8561d57e01ddb22f93f9b454 upstream.
Infinite loop can occur if IOCStatus is not equal to
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions
_scsih_search_responding_sas_devices,
_scsih_search_responding_raid_devices and
_scsih_search_responding_expanders
So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value,
in this patch code is modified to check for IOCStatus not equals to
MPI2_IOCSTATUS_SUCCESS to break the while loop.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0df96a0068daee4f9c2189c29b9053eb6e46b17 upstream.
Missing delay is not getting set properly. The reason is that it is not
defined in the same file from where it is being invoked. The fix is to move
the missing delay module parameter from mpt2sas_base.c to mpt2sas_scsh.c.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48ba2efc382f94fae16ca8ca011e5961a81ad1ea upstream.
When SCSI command is received with task attribute not set, set it to SIMPLE.
Previously it is set to untagged. This causes the firmware to fail the commands.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5bebd829dd95602c15f8da8cc50fa938b5e0254 upstream.
One of the customer had reported that the set of raid logical arrays will
become unavailable (I/O offline) after a long hours of IO stress test. The OS
wouldn`t be accessible afterwards and require a hard reset.
This driver patch has a fix for race condition between the doorbell and the
circular buffer. The driver is modified to do an extra read after clearing the
doorbell in case there had been a completion posted during the small timing
window.
With this fix, we ran IO stress for ~13 days. There were no IO failures.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66c28f97120e8a621afd5aa7a31c4b85c547d33d upstream.
SATA drives located behind a SAS controller would incorrectly receive
WRITE SAME commands. Tweak the heuristics so that:
- If REPORT SUPPORTED OPERATION CODES is provided we will use that to
choose between WRITE SAME(16), WRITE SAME(10) and disabled. This also
fixes an issue with the old code which would issue WRITE SAME(10)
despite the command not being whitelisted in REPORT SUPPORTED
OPERATION CODES.
- If REPORT SUPPORTED OPERATION CODES is not provided we will fall back
to WRITE SAME(10) unless the device has an ATA Information VPD page.
The assumption is that a SATL which is smart enough to implement
WRITE SAME would also provide REPORT SUPPORTED OPERATION CODES.
To facilitate the new heuristics scsi_report_opcode() has been modified
to so we can distinguish between "operation not supported" and "RSOC not
supported".
Reported-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ee3e26c673e75c05ef8b914f54fadee3d7b9c88 upstream.
Commit 39c60a0948cc '[SCSI] sd: fix array cache flushing bug causing
performance problems' added temp as a pointer to "temporary " and used
sizeof(temp) - 1 as its length. But sizeof(temp) is the size of the
pointer, not the size of the string constant. Change temp to a static
array so that sizeof() does what was intended.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ffc8b30866879ed9ba62bd0a86fecdbd51cd3d19 upstream.
Disk names may contain arbitrary strings, so they must not be
interpreted as format strings. It seems that only md allows arbitrary
strings to be used for disk names, but this could allow for a local
memory corruption from uid 0 into ring 0.
CVE-2013-2851
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a critical bug that was introduced in 3.9
related to VLAN tagging FCoE frames.
|
|
3.10 fixes
|
|
fcoe_xmit was coded such that it would skip the vlan net device/layer
and instead set some vlan flags and transmit on the real net device.
The real net device has code that would add the vlan tag for fcoe skbs.
This avoids some extra processing for data frames and provides a small
performance improvement.
Since fcoe_xmit was not using the vlan net device, __vlan_put_tag
within the real net device's xmit routine was ultimately being
called to set the vlan tag.
With the below change the behavior of __vlan_put_tag changed slightly,
it now sets the skb->protocol = vlan_proto. vlan_proto was not a field
being set by fcoe_xmit, so the skb->protocol is now not being set to
ETH_P_8021Q, as it should be.
This patch converts fcoe_xmit to use the vlan_put_tag routine which
will tag the skb and fcoe will continue to transmit fcoe skbs on the
real net device.
For reference, the below change was the one that altered the
__vlan_put_tag behavior.
commit 86a9bad3ab6b6f858fd4443b48738cabbb6d094c
Author: Patrick McHardy <kaber@trash.net>
Date: Fri Apr 19 02:04:30 2013 +0000
net: vlan: add protocol argument to packet tagging functions
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Included is the recent tcm_qla2xxx residual underrun length fix from
Roland, along with Joern's iscsi-target patch for session_lock
breakage within iscsit_stop_time2retain_timer() code. Both are CC'ed
to stable.
The remaining two are specific to recent iscsi-target + iser
conversion changes. One drops some left-over debug noise, and Andy's
patch fixes configfs attribute handling during an explicit network
portal feature bit disable when iser-target is unsupported."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Remove left over v3.10-rc debug printks
target/iscsi: Fix op=disable + error handling cases in np_store_iser
tcm_qla2xxx: Fix residual for underrun commands that fail
target/iscsi: don't corrupt bh_count in iscsit_stop_time2retain_timer()
|
|
When you copy some code, you are supposed to read it. If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...
X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Suppose an initiator sends a DATA IN command with an allocation length
shorter than the FC transfer length -- we get a target message like
TARGET_CORE[qla2xxx]: Expected Transfer Length: 256 does not match SCSI CDB Length: 0 for SAM Opcode: 0x12
In that case, the target core adjusts the data_length and sets
se_cmd->residual_count for the underrun. But now suppose that command
fails and we end up in tcm_qla2xxx_queue_status() -- that function
unconditionally overwrites residual_count with the already adjusted
data_length, and the initiator will burp with a message like
qla2xxx [0000:00:06.0]-301d:0: Dropped frame(s) detected (0x100 of 0x100 bytes).
Fix this by adding on to the existing underflow residual count instead.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
|
|
That patch failed to set proc_scsi_fops' .release method.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Drop unused transport_wait_for_tasks() check in target_wait_for_sess_cmds
shutdown code, and convert tcm_qla2xxx + ib_srpt fabric drivers.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Defined target_ids,array_ids and vsets_ids as unsigned long to avoid
target_destroy accessing memory after it was freed.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The driver uses ha->mbx_cmd_flags variable to pass information between
its ISR and mailbox routines, however, it does so without the protection of
any locks. Under certain conditions, this can lead to multiple mailbox
command completions being signaled, which, in turn, leads to a false
mailbox timeout error for the subsequently issued mailbox command.
The issue occurs frequently but intermittenly with the Qlogic 8GFC mezz
card during card initialization, resulting in card initialization failure.
Signed-off-by: Gurinder (Sunny) Shergill <gurinder.shergill@hp.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This warning was reported recently:
WARNING: at drivers/scsi/libfc/fc_exch.c:478 fc_seq_send+0x14f/0x160 [libfc]()
(Not tainted)
Hardware name: ProLiant DL120 G7
Modules linked in: tcm_fc target_core_iblock target_core_file target_core_pscsi
target_core_mod configfs dm_round_robin dm_multipath 8021q garp stp llc bnx2fc
cnic uio fcoe libfcoe libfc scsi_transport_fc scsi_tgt autofs4 sunrpc
pcc_cpufreq ipv6 hpilo hpwdt e1000e microcode iTCO_wdt iTCO_vendor_support
serio_raw shpchp ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif pata_acpi
ata_generic ata_piix hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded:
scsi_wait_scan]
Pid: 5464, comm: target_completi Not tainted 2.6.32-272.el6.x86_64 #1
Call Trace:
[<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[<ffffffffa025f7df>] ? fc_seq_send+0x14f/0x160 [libfc]
[<ffffffffa035cbce>] ? ft_queue_status+0x16e/0x210 [tcm_fc]
[<ffffffffa030a660>] ? target_complete_ok_work+0x0/0x4b0 [target_core_mod]
[<ffffffffa030a766>] ? target_complete_ok_work+0x106/0x4b0 [target_core_mod]
[<ffffffffa030a660>] ? target_complete_ok_work+0x0/0x4b0 [target_core_mod]
[<ffffffff8108c760>] ? worker_thread+0x170/0x2a0
[<ffffffff810920d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108c5f0>] ? worker_thread+0x0/0x2a0
[<ffffffff81091d66>] ? kthread+0x96/0xa0
[<ffffffff8100c14a>] ? child_rip+0xa/0x20
[<ffffffff81091cd0>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
It occurs because fc_seq_send can have multiple contexts executing within it at
the same time, and fc_seq_send doesn't consistently use the ep->ex_lock that
protects this structure. Because of that, its possible for one context to clear
the INIT bit in the ep->esb_state field while another checks it, leading to the
above stack trace generated by the WARN_ON in the function.
We should probably undertake the effort to convert access to the fc_exch
structures to use rcu, but that a larger work item. To just fix this specific
issue, we can just extend the ex_lock protection through the entire fc_seq_send
path
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Gris Ge <fge@redhat.com>
CC: Robert Love <robert.w.love@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
The service_params field is being checked against the symbol
FC_RPORT_ROLE_FCP_INITIATOR where it really should be checked
against FCP_SPPF_INIT_FCN.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
When multiple FCFs in use, and first FIP Advertisement received is
with "Available for Login" i.e A bit set to 0, FCF selection will fail.
The fix is to remove the assumption in the code that first FCF is only
allowed selectable FCF.
Consider the scenario fip->fcfs contains FCF1(fabricname X, marked A=0)
FCF2(fabricname Y, marked A=1). list_first_entry(first) points to FCF1
and 1st iteration we ignore the FCF and on 2nd iteration we compare
FCF1 & FCF2 fabric name and we fails to perform FCF selection.
Signed-off-by: Krishna Mohan <krmohan@cisco.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
sas_device_type
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants
[jejb: fix up tabs and spaces issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.
[jejb: fix checkpatch issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
region for it
Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
changes in common files
Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
