| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds support for the Simtek STK17TA8 timekeeping chip.
The STK17TA8 is quite similar to the DS1553, but differs in register layout
and in various control bits in the registers. I chose to make this a new
driver to avoid confusion in the code and to not get lost in #ifdefs.
Signed-off-by: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We now read and write the century byte in the max6900 chip. We probably
don't need to do so on Linux-only system, but it's necessary when the chip
is shared by another OS that uses the century byte.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Various people have expressed surprise that their modular RTC drivers don't
seem to work for initializing the system time at boot. To help avoid such
unpleasantness, make the Kconfig text point out that the driver probably
needs to be statically linked.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes these sparse warnings:
drivers/rtc/rtc-ds1742.c:265:2: warning: returning void-valued expression
drivers/rtc/rtc-ds1553.c:409:2: warning: returning void-valued expression
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Both shwdt and rtc-sh are only supported on SH-3 and SH-4 at
the moment, don't allow them to break the SH-2 and SH-5 (sh64)
builds.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Adds support for periodic irq enabling in rtc-cmos. This could be used by
the ALSA driver and is already being tested with the zaptel ztdummy module.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add Texas Instruments TWL92330/Menelaus Power Management chip driver. This
includes voltage regulators, Dual slot memory card tranceivers and
real-time clock(RTC).
The support for RTC is integrated with this driver only; it is not separate
module. Passes 'rtctest' on OMAP H4 EVM, other than lack of "periodic"
(1/N second) IRQs. System wakeup alarms (from suspend-to-RAM) work too.
The battery keeps the RTC active over power off, so once you set clock
(rdate/ntpdate/etc, then "hwclock -w") then RTC_HCTOSYS at boot time will
behave as expected.
Cc: "Jean Delvare" <khali@linux-fr.org>
Cc: "Tony Lindgren" <tony@atomide.com>
Cc: "David Brownell" <david-b@pacbell.net>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert the rtc-ds1307 driver into a "new style" driver.
Also improve probe() checks: be more correct about switching out of
AM/PM mode, and issue a (debug) diagnostic when failing due to bogus
register values.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we find a ds1337 or ds1339 with the oscillator powered off, turn it
on. If the oscillator fault flag was set, clear it and warn that the clock
needs to be set.
David Brownell: Bugfixes; provide corresponding update for ds1338, and the
core of the fix for ds1340. Use a common warning message ("SET TIME!")
whenever the clock needs to be set after oscillator fault (or oscillator
enable, if fault is not a separate status).
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC driver for Dallas/Maxim DS126 chips used in SNI RM200/RM400
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[akpm@linux-foundation.org: x86_64 build fix]
[akpm@linux-foundation.org: The acpi guys changed the bin_attribute code]
Signed-off-by: Mark Zhan <rongkai.zhan@windriver.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a watchdog driver interface to rtc-m41t80 driver. This is derived from
works by Alexander Bigga <ab@mycable.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Alexander Bigga <ab@mycable.de>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a new-style i2c driver for ST M41T80 series RTC chip, derived from
works by Alexander Bigga <ab@mycable.de> who wrote the original
rtc-m41txx.c based on drivers/i2c/chips/m41t00.c driver.
This driver supports M41T8[0-4] and M41ST8[457]. The old m41t00 driver
supports M41T00, M41T81 and M41T85(M41ST85). While the M41T00 chip is now
supported by rtc-ds1307 driver, this driver does not include support for
the chip.
[akpm@linux-foundation.org: remove bogus `static']
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Alexander Bigga <ab@mycable.de>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Minor fix to the Kconfig for RTCs: don't display section headers for I2C or
SPI unless they're configured. And depend on SPI_MASTER; having slave
support wouldn't help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC class is mature enough.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tested on the AT32AP7000/ATSTK1000. Driver does only suport time, wake up
and a very simple alarm, because of hardware limitations.
Hardware documentation can be found in the AT32AP7000 data sheet, which can
be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
From: David Brownell <david-b@pacbell.net>
- Strike some alarm setup code that's no longer needed.
(This patch seems to have gotten lost somewhere...)
- Make the driver name (and its module alias) match what
the platform setup code uses, so the driver can bind
and hotplug.
[akpm@linux-foundation.org: fix several checkpatch.pl warnings]
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert rtc-rs5c372 to be a "new style" I2C driver, and update the
Kconfig text to be more complete..
Verified on an OMAP H4 development platform, along with a board
init patch to declare its rv5c387a device.
Only one defconfig -- powerpc/linkstation -- uses this driver; but
several other platforms use it, just without defconfig support.
Such platforms need to be converted so (a) their I2C adapter driver
supports new-style drivers, and (b) board init code declares this
I2C device.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Voipio Riku <Riku.Voipio@movial.fi>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This updates the rtc-ds1307 driver so that converting it to a "new style"
driver (driver model, not legacy i2c model) will involve fewer changes.
- Use pointer to i2c_client almost everywhere, so that it's easy
to let the i2c core create that object;
- Avoid using i2c_client.adapter, since that field is redundant and
thus may go away (same object as i2c_client.dev.parent).
- Extend type enum to include various RTCs this is expected to
work with, and include register support for them.
It also cleans up the support for multiple chip types, and fixes a
glitch that could appear with an un-initialized RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
sysfs: make directory dentries and inodes reclaimable
sysfs: implement sysfs_get_dentry()
sysfs: move sysfs_drop_dentry() to dir.c and make it static
sysfs: restructure add/remove paths and fix inode update
sysfs: use sysfs_mutex to protect the sysfs_dirent tree
sysfs: consolidate sysfs spinlocks
sysfs: make kobj point to sysfs_dirent instead of dentry
sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
sysfs: implement SYSFS_FLAG_REMOVED flag
sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
sysfs: make sysfs_drop_dentry() access inodes using ilookup()
sysfs: Fix oops in sysfs_drop_dentry on x86_64
sysfs: use singly-linked list for sysfs_dirent tree
sysfs: slim down sysfs_dirent->s_active
sysfs: move s_active functions to fs/sysfs/dir.c
sysfs: fix root sysfs_dirent -> root dentry association
sysfs: use iget_locked() instead of new_inode()
sysfs: reorganize sysfs_new_indoe() and sysfs_create()
sysfs: fix parent refcounting during rename and move
...
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
|
|
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The x1205 driver moved to the RTC subsystem and was significantly
modified since then, so just delete the outdated documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
|
|
sysfs binary attributes
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The powerpc arch uses CONFIG_PPC instead of CONFIG_POWERPC. This fixes
drivers/rtc/Kconfig to use the correct config option.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Intel Macs (and possibly other machines) provide a PNP entry for the RTC,
but provide no IRQ. As a result the rtc-cmos driver doesn't allow wakeup
alarms. If the RTC is located at the legacy ioport range, assume that it's
on IRQ 8 unless the tables say otherwise.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix typo which breaks build. How did that happen?
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (28 commits)
[MIPS] Rework cobalt_board_id
[MIPS] Use RTC_CMOS for Cobalt
[MIPS] Use platform_device for Cobalt UART
[MIPS] Separate Alchemy processor based boards config
[MIPS] Fix build error in atomic64_cmpxchg
[MIPS] Run checksyscalls for N32 and O32 ABI
[MIPS] tlbex: use __maybe_unused
[MIPS] excite: use __maybe_unused
[MIPS] Add extern cobalt_board_id
[MIPS] Remove unused CONFIG_TOSHIBA_BOARDS
[MIPS] Rename tb0229_defconfig to tb0219_defconfig
[MIPS] Update tb0229_defconfig; add CONFIG_GPIO_TB0219.
[MIPS] Add minimum defconfig for RBHMA4200
[MIPS] SB1: Build fix.
[MIPS] Drop __devinit tag from allocate_irqno() and free_irqno()
[MIPS] clocksource: use CLOCKSOURCE_MASK() macro
[MIPS] Remove LIMITED_DMA support
[MIPS] Remove Momenco Jaguar ATX support
[MIPS] Remove Momenco Ocelot G support
[MIPS] FPU hazard handling
...
|
|
Add error processing. Hanging up by an infinite loop is evaded.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correct an initial value of suruct rtc_ time.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correct a compile error and warning.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Disable some more menus in the configuration files that are of no
interest to a s390 machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix stacktrace simplification fallout.
sh: SH7760 DMABRG support.
sh: clockevent/clocksource/hrtimers/nohz TMU support.
sh: Truncate MAX_ACTIVE_REGIONS for the common case.
rtc: rtc-sh: Fix rtc_dev pointer for rtc_update_irq().
sh: Convert to common die chain.
sh: Wire up utimensat syscall.
sh: landisk mv_nr_irqs definition.
sh: Fixup ndelay() xloops calculation for alternate HZ.
sh: Add 32-bit opcode feature CPU flag.
sh: Fix PC adjustments for varying opcode length.
sh: Support for SH-2A 32-bit opcodes.
sh: Kill off redundant __div64_32 symbol export.
sh: Share exception vector table for SH-3/4.
sh: Always define TRAPA_BUG_OPCODE.
sh: __GFP_REPEAT for pte allocations, too.
rtc: rtc-sh: Fix up dev_dbg() warnings.
sh: generic quicklist support.
|
|
Fix several typos in help text in Kconfig* files.
Signed-off-by: David Sterba <dave@jikos.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
When the rtc_update_irq() callsites stopped passing in the
class_dev, the rtc_dev references weren't fixed. Fix it up,
so we pass in the proper pointer.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Replace CONFIG_PNPACPI with CONFIG_PNP, so it loads on ACPI-less PNPBIOS
systems.
Signed-off-by: Marko Vrh <mvrh@freeshells.ch>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes a common glitch in how RTC drivers handle two "set alarm" modes,
by getting rid of the surprising/hidden one that was rarely implemented
correctly (and which could expose nonportable hardware-specific behavior).
The glitch comes from the /dev/rtcX logic implementing the legacy
RTC_ALM_SET (limited to 24 hours, needing RTC_AIE_ON) ioctl on top of the
RTC driver call providing access to the newer RTC_WKALM_SET (without those
limitations) by initializing the day/month/year fields to be invalid ...
that second mode.
Now, since few RTC drivers check those fields, and most hardware misbehaves
when faced with invalid date fields, many RTC drivers will set bogus alarm
times on those RTC_ALM_SET code paths. (Several in-tree drivers have that
issue, and I also noticed it with code reviews on several new RTC drivers.)
This patch ensures that RTC drivers never see such invalid alarm fields, by
moving some logic out of rtc-omap into the RTC_ALM_SET code and adding an
explicit check (which will prevent the issue on other code paths).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
David says "884b4aaaa242a2db8c8252796f0118164a680ab5 should be reverted. It
added an rtc_merge_alarm() call to the 2.6.20 kernel, which hasn't yet been
used by any in-tree driver; this patch obviates the need for that call, and
uses a more robust approach."
Cc: Scott Wood <scottwood@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I finally got around to testing the updated wakeup event hooks for rtc-cmos,
and they follow in two patches:
- Interface update ... when a simple enable_irq_wake() doesn't suffice,
the platform data can hold suspend/resume callback hooks.
- ACPI implementation ... provides callback hooks to do ACPI magic, and
eliminate the legacy /proc/acpi/alarm file.
The interface update could go into 2.6.21, but that's not essential; they
will be NOPs on most PCs, without the ACPI stuff.
I suspect the ACPI folk may have opinions about how to merge that second
patch, and how to obsolete that legacy procfs file. I'd like to see that
merge into 2.6.22 if possible...
As for how to kick it in ... two ways:
- The appended "rtcwake" program; updated since the last time it was
posted, it deals much better with timezones and DST.
- Write the /sys/class/rtc/.../wakealarm file, then go to sleep.
For some reason RTC wake from "swsusp" stopped working on a system where
it previously worked; the alarm setting appears to get clobbered. But
on the bright side, RTC wake from "standby" worked on a system that had
never been able to resume from that state before ... IDEACPI is my guess
as to why it finally started to work. It's the old "two steps forward,
one step back" dance, I guess.
- Dave
/* gcc -Wall -Os -o rtcwake rtcwake.c */
#include <stdio.h>
#include <getopt.h>
#include <fcntl.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#include <errno.h>
#include <time.h>
#include <sys/ioctl.h>
#include <sys/time.h>
#include <sys/types.h>
#include <linux/rtc.h>
/* constants from legacy PC/AT hardware */
#define RTC_PF 0x40
#define RTC_AF 0x20
#define RTC_UF 0x10
/*
* rtcwake -- enter a system sleep state until specified wakeup time.
*
* This uses cross-platform Linux interfaces to enter a system sleep state,
* and leave it no later than a specified time. It uses any RTC framework
* driver that supports standard driver model wakeup flags.
*
* This is normally used like the old "apmsleep" utility, to wake from a
* suspend state like ACPI S1 (standby) or S3 (suspend-to-RAM). Most
* platforms can implement those without analogues of BIOS, APM, or ACPI.
*
* On some systems, this can also be used like "nvram-wakeup", waking
* from states like ACPI S4 (suspend to disk). Not all systems have
* persistent media that are appropriate for such suspend modes.
*
* The best way to set the system's RTC is so that it holds the current
* time in UTC. Use the "-l" flag to tell this program that the system
* RTC uses a local timezone instead (maybe you dual-boot MS-Windows).
*/
static char *progname;
#ifdef DEBUG
#define VERSION "1.0 dev (" __DATE__ " " __TIME__ ")"
#else
#define VERSION "0.9"
#endif
static unsigned verbose;
static int rtc_is_utc = -1;
static int may_wakeup(const char *devname)
{
char buf[128], *s;
FILE *f;
snprintf(buf, sizeof buf, "/sys/class/rtc/%s/device/power/wakeup",
devname);
f = fopen(buf, "r");
if (!f) {
perror(buf);
return 0;
}
fgets(buf, sizeof buf, f);
fclose(f);
s = strchr(buf, '\n');
if (!s)
return 0;
*s = 0;
/* wakeup events could be disabled or not supported */
return strcmp(buf, "enabled") == 0;
}
/* all times should be in UTC */
static time_t sys_time;
static time_t rtc_time;
static int get_basetimes(int fd)
{
struct tm tm;
struct rtc_time rtc;
/* this process works in RTC time, except when working
* with the system clock (which always uses UTC).
*/
if (rtc_is_utc)
setenv("TZ", "UTC", 1);
tzset();
/* read rtc and system clocks "at the same time", or as
* precisely (+/- a second) as we can read them.
*/
if (ioctl(fd, RTC_RD_TIME, &rtc) < 0) {
perror("read rtc time");
return 0;
}
sys_time = time(0);
if (sys_time == (time_t)-1) {
perror("read system time");
return 0;
}
/* convert rtc_time to normal arithmetic-friendly form,
* updating tm.tm_wday as used by asctime().
*/
memset(&tm, 0, sizeof tm);
tm.tm_sec = rtc.tm_sec;
tm.tm_min = rtc.tm_min;
tm.tm_hour = rtc.tm_hour;
tm.tm_mday = rtc.tm_mday;
tm.tm_mon = rtc.tm_mon;
tm.tm_year = rtc.tm_year;
tm.tm_isdst = rtc.tm_isdst; /* stays unspecified? */
rtc_time = mktime(&tm);
if (rtc_time == (time_t)-1) {
perror("convert rtc time");
return 0;
}
if (verbose) {
if (!rtc_is_utc) {
printf("\ttzone = %ld\n", timezone);
printf("\ttzname = %s\n", tzname[daylight]);
gmtime_r(&rtc_time, &tm);
}
printf("\tsystime = %ld, (UTC) %s",
(long) sys_time, asctime(gmtime(&sys_time)));
printf("\trtctime = %ld, (UTC) %s",
(long) rtc_time, asctime(&tm));
}
return 1;
}
static int setup_alarm(int fd, time_t *wakeup)
{
struct tm *tm;
struct rtc_wkalrm wake;
tm = gmtime(wakeup);
wake.time.tm_sec = tm->tm_sec;
wake.time.tm_min = tm->tm_min;
wake.time.tm_hour = tm->tm_hour;
wake.time.tm_mday = tm->tm_mday;
wake.time.tm_mon = tm->tm_mon;
wake.time.tm_year = tm->tm_year;
wake.time.tm_wday = tm->tm_wday;
wake.time.tm_yday = tm->tm_yday;
wake.time.tm_isdst = tm->tm_isdst;
/* many rtc alarms only support up to 24 hours from 'now' ... */
if ((rtc_time + (24 * 60 * 60)) > *wakeup) {
if (ioctl(fd, RTC_ALM_SET, &wake.time) < 0) {
perror("set rtc alarm");
return 0;
}
if (ioctl(fd, RTC_AIE_ON, 0) < 0) {
perror("enable rtc alarm");
return 0;
}
/* ... so use the "more than 24 hours" request only if we must */
} else {
/* avoid an extra AIE_ON call */
wake.enabled = 1;
if (ioctl(fd, RTC_WKALM_SET, &wake) < 0) {
perror("set rtc wake alarm");
return 0;
}
}
return 1;
}
static void suspend_system(const char *suspend)
{
FILE *f = fopen("/sys/power/state", "w");
if (!f) {
perror("/sys/power/state");
return;
}
fprintf(f, "%s\n", suspend);
fflush(f);
/* this executes after wake from suspend */
fclose(f);
}
int main(int argc, char **argv)
{
static char *devname = "rtc0";
static unsigned seconds = 0;
static char *suspend = "standby";
int t;
int fd;
time_t alarm = 0;
progname = strrchr(argv[0], '/');
if (progname)
progname++;
else
progname = argv[0];
if (chdir("/dev/") < 0) {
perror("chdir /dev");
return 1;
}
while ((t = getopt(argc, argv, "d:lm:s:t:uVv")) != EOF) {
switch (t) {
case 'd':
devname = optarg;
break;
case 'l':
rtc_is_utc = 0;
break;
/* what system power mode to use? for now handle only
* standardized mode names; eventually when systems define
* their own state names, parse /sys/power/state.
*
* "on" is used just to test the RTC alarm mechanism,
* bypassing all the wakeup-from-sleep infrastructure.
*/
case 'm':
if (strcmp(optarg, "standby") == 0
|| strcmp(optarg, "mem") == 0
|| strcmp(optarg, "disk") == 0
|| strcmp(optarg, "on") == 0
) {
suspend = optarg;
break;
}
printf("%s: unrecognized suspend state '%s'\n",
progname, optarg);
goto usage;
/* alarm time, seconds-to-sleep (relative) */
case 's':
t = atoi(optarg);
if (t < 0) {
printf("%s: illegal interval %s seconds\n",
progname, optarg);
goto usage;
}
seconds = t;
break;
/* alarm time, time_t (absolute, seconds since 1/1 1970 UTC) */
case 't':
t = atoi(optarg);
if (t < 0) {
printf("%s: illegal time_t value %s\n",
progname, optarg);
goto usage;
}
alarm = t;
break;
case 'u':
rtc_is_utc = 1;
break;
case 'v':
verbose++;
break;
case 'V':
printf("%s: version %s\n", progname, VERSION);
break;
default:
usage:
printf("usage: %s [options]"
"\n\t"
"-d rtc0|rtc1|...\t(select rtc)"
"\n\t"
"-l\t\t\t(RTC uses local timezone)"
"\n\t"
"-m standby|mem|...\t(sleep mode)"
"\n\t"
"-s seconds\t\t(seconds to sleep)"
"\n\t"
"-t time_t\t\t(time to wake)"
"\n\t"
"-u\t\t\t(RTC uses UTC)"
"\n\t"
"-v\t\t\t(verbose messages)"
"\n\t"
"-V\t\t\t(show version)"
"\n",
progname);
return 1;
}
}
if (!alarm && !seconds) {
printf("%s: must provide wake time\n", progname);
goto usage;
}
/* REVISIT: if /etc/adjtime exists, read it to see what
* the util-linux version of hwclock assumes.
*/
if (rtc_is_utc == -1) {
printf("%s: assuming RTC uses UTC ...\n", progname);
rtc_is_utc = 1;
}
/* this RTC must exist and (if we'll sleep) be wakeup-enabled */
fd = open(devname, O_RDONLY);
if (fd < 0) {
perror(devname);
return 1;
}
if (strcmp(suspend, "on") != 0 && !may_wakeup(devname)) {
printf("%s: %s not enabled for wakeup events\n",
progname, devname);
return 1;
}
/* relative or absolute alarm time, normalized to time_t */
if (!get_basetimes(fd))
return 1;
if (verbose)
printf("alarm %ld, sys_time %ld, rtc_time %ld, seconds %u\n",
alarm, sys_time, rtc_time, seconds);
if (alarm) {
if (alarm < sys_time) {
printf("%s: time doesn't go backward to %s",
progname, ctime(&alarm));
return 1;
}
alarm += sys_time - rtc_time;
} else
alarm = rtc_time + seconds + 1;
if (setup_alarm(fd, &alarm) < 0)
return 1;
sync();
printf("%s: wakeup from \"%s\" using %s at %s",
progname, suspend, devname,
ctime(&alarm));
fflush(stdout);
usleep(10 * 1000);
if (strcmp(suspend, "on") != 0)
suspend_system(suspend);
else {
unsigned long data;
do {
t = read(fd, &data, sizeof data);
if (t < 0) {
perror("rtc read");
break;
}
if (verbose)
printf("... %s: %03lx\n", devname, data);
} while (!(data & RTC_AF));
}
if (ioctl(fd, RTC_AIE_OFF, 0) < 0)
perror("disable rtc alarm interrupt");
close(fd);
return 0;
}
This patch:
Make rtc-cmos do the relevant magic so this RTC can wake the system from a
sleep state. That magic comes in two basic flavors:
- Straightforward: enable_irq_wake(), the way it'd work on most SOC chips;
or generally with system sleep states which don't disable core IRQ logic.
- Roundabout, using non-IRQ platform hooks. This is needed with ACPI and
one almost-clone chip which uses a special wakeup-only alarm. (That's
the RTC used on Footbridge boards, FWIW, which don't do PM in Linux.)
A separate patch implements those hooks for ACPI platforms, so that rtc_cmos
can issue system wakeup events (and its sysfs "wakealarm" attribute works on
at least some systems).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- vr41xx_rtc_read_alarm() reports alarm enabled.
- vr41xx_rtc_set_alarm() sets alarm disable/enable by rtc_wkalrm.enabled.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a goof in the revised classdev support for RTCs: make sure the /dev
node info is ready before the device is registered, not after. Otherwise
the /sys/class/rtc/rtcN/dev attribute won't be created and then udev won't
have the information it needs to create the /dev/rtcN node.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC class suspend/resume support, re-initializing the system clock on resume
from the clock used to initialize it at boot time.
- The reinit-on-resume is hooked to the existing RTC_HCTOSYS config
option, on the grounds that a clock good enough for init must also
be good enough for re-init.
- Inlining a version of the code used by ARM, to save and restore the
delta between a selected RTC and the current system wall-clock time.
- Removes calls to that ARM code from AT91, OMAP1, and S3C RTCs. This
means that systems using those RTCs across suspend/resume will likely
want to change their kernel configs to enable RTC_HCTOSYS.
If HCTOSYS isn't using a second RTC (with battery?), this changes the
system's initial date from Jan 1970 to the epoch this hardware uses:
1998 for AT91, 2000 for OMAP1 (assuming no split power mode), etc.
This goes on top of the patch series removing "struct class_device" usage
from the RTC framework. That's all needed for class suspend()/resume().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-By: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Finish converting the RTC framework so it no longer uses class_device.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-By: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
