summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2013-04-03iwlwifi: mvm: set keepalive period regardless of PM stateAlexander Bondar2-3/+11
The firmware starts sending nulldata frames for keepalive immediately after association, regardless of power management state. The driver thus needs to configure keep alive period unconditionally. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: always send power table commandAlexander Bondar1-14/+12
The driver distinguishes between power management and device's power down enablement. Power management enablement depends both on driver's module power parameters and mac80211 decision. The device's power down depends only on driver's module power parameters. Change the driver to always send Power Table command to enable or disable both power management and device's power down. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: Fix active-to-powersave transition time unitsAlexander Bondar1-4/+4
Active to power save mode transition time for TX/RX in the power table command is in microseconds, fix the units in the driver. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: don't disable power management due to P2P deviceAlexander Bondar2-5/+17
Currently power management is supported only when only a single virtual interface is present. The driver verifies number of created interfaces and disables power management when multiple interfaces present. However, this rule does not extend to a P2P device that is handled differently in the firmware. If a P2P device is added power management can remain enabled. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: Rename some power management definitions and methodsAlexander Bondar2-7/+8
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM. Add iwl_mvm prefix to a function name. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: downgrade to old power management APIAlexander Bondar2-67/+27
Current available FW still doesn't support new PM API. Therefore, to enable basic power management with the existing firmware, change the API in the driver back to the API used in the current firmware. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: remove BT Coex constraints upon roaming to A bandEmmanuel Grumbach3-17/+52
When we roam to A band, we don't need to constraint WiFi any more since it is operating on a different band. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: implement reduced Tx powerEmmanuel Grumbach5-38/+283
This allows to have better wifi TPT when BT is active under good RSSI conditions. Wifi will have better chance to send Acks and Cts even if BT is active. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: add per-interface debugfs with mac_params fileJohannes Berg3-2/+124
Use the per-interface debugfs infrastructure to create a directory and symlink, and add a file containing debug data related to each virtual interface. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-26Merge remote-tracking branch 'wireless-next/master' into iwlwifi-nextJohannes Berg44-236/+646
2013-03-26iwlwifi: mvm: split long debug printEmmanuel Grumbach1-4/+6
This caused issues with tracing as it's longer than the buffer size used there. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-26iwlwifi: mvm: ignore bt_ch_announce module parameterEmmanuel Grumbach1-2/+1
This module parameter isn't and won't be used. So ignore its value and set BT_CH_ANNOUNCE unconditionally. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-25b43: remove warning for LP-PHY with sprom < 8Hauke Mehrtens1-9/+3
The BCM5354 SoC has a build in ieee80211 core rev 13 with a LP-PHY on it. This devices has a sprom version 3 stored in the nvram. This patch removes the warning and uses the opo values from the sprom as mentioned in the specs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25b43: use bcma_chipco_gpio_control()Hauke Mehrtens1-5/+2
With this patch the same registers are written, but this access is now protected by a lock. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25mwifiex: add support to configure VHT for AP modeYogesh Ashok Powar9-0/+129
Currently, default VHT configuration from the firmware is used for the VHT operations. Adding vhtcfg command to configure the firmware based on input received from cfg. Enable VHT for AP mode only when cfg80211_ap_settings has a VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf. Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25rtlwifi: usb: add NET_IP_ALIGN padding to RX skb when neededJussi Kivilinna1-1/+40
Add proper alignment at first packet copy, to avoid extra copies made later in networking stack. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25rtlwifi: usb: defer rx processing to taskletJussi Kivilinna3-15/+51
Move processing of received packets to tasklet from hard-irq context. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25rtlwifi: usb: remove extra skb copy on RX pathJussi Kivilinna1-15/+4
RX path has extra copying of packets, that can be avoided. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25rtlwifi: usb: use usb_alloc_coherent for RX buffersJussi Kivilinna2-47/+68
Use dedicated DMA coherent buffers for RX urbs, to avoid allocation of large skbuffs in hard-irq context and improve performance. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-25Merge branch 'for-linville' of ↵John W. Linville17-130/+330
git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx
2013-03-25Merge branch 'for-john' of ↵John W. Linville21-253/+195
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
2013-03-25Merge branch 'for-john' of ↵John W. Linville13-14/+19
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-03-25Merge branch 'wl12xx-next' into for-linvilleLuciano Coelho17-130/+330
2013-03-25wlcore: move handling from hardirq to the irq thread functionLuciano Coelho1-32/+21
Spin locks and completions are expensive in hard IRQ context and cause problems with RT kernels. In RT kernels, both spin locks and completions can schedule(), so we can't use them in hard irq context. Move handling code into the irq thread function to avoid that. Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: use print_hex_dump_debug()Luciano Coelho1-17/+16
We were printing out all the hex dumps regardless of whether dynamic debugging was enabled or not. Now that print_hex_dump_debug() has been implemented, we can use that instead. Reported-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: consider dummy packets when tx queues are emptyArik Nemtsov1-1/+1
Don't ignore dummy packets when our queues are empty. This causes dummy packets never to be sent when traffic is not suspended by FW thresholds, which happens only in high Tx throughput situations. This may hurt Rx performance. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: correctly check state before regdomain confArik Nemtsov1-2/+5
The wlcore state was checked without the mutex being taken. This leads to WARN_ONs sometimes if a notification arrives when the driver is on, but the mutex is only taken after it is off. This usually happens if stopping the driver while connected to a network. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: AP-mode - recover security seq num for stationsArik Nemtsov3-1/+44
Save the sequence number of the broadcast AP link in the wlvif. For each connected station, save the sequence number in the drv_priv part of ieee80211_sta. Use the saved numbers on recovery/resume, with the obligatory increment on recovery. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: free AP global links properly on recoveryArik Nemtsov2-2/+4
Dont use free_sta() on AP global links. It would fail an internal check within the function and various structures within the link struct would not be reset. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wl18xx: print chip info during bootVictor Goldenshtein2-1/+52
Print board type, PG with metal and ROM versions. This might help debugging HW related issues. Signed-off-by: Victor Goldenshtein <victorg@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: don't attempt to roam in case of p2pEyal Shapira1-1/+8
For STA we report beacon loss to higher levels so that wpa_s can attempt to roam without disconnecting. In case of P2P CLI we don't want to attempt roaming and instead disconnect immediately upon beacon loss. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: change warn on missing lock in wlcore_queue_xx funcsArik Nemtsov1-2/+3
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the locking using assert_spin_locked, which is written to behave correctly in all cases. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: report rssi from roaming statisticsNadim Zubidat3-0/+77
report the average beacon rssi which is calculated by firmware for roaming statistics instead of the last rx packet rssi. this results a more accurate rssi reporting Signed-off-by: Nadim Zubidat <nadimz@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: consolidate tx_seq handling on recoveryArik Nemtsov5-56/+67
Accumulate the total number of sent packets per-link to find out how far the encryption sequence number has progressed. Use this number as the initial security sequence number after recovery. This consolidates security sequence handling for both chip families, as we no longer have to rely on 12xx specific Tx completion. A fortunate side effect of this is correct management of seq numbers for AP roles and multi-role scenarios. When a link is removed we save the last seq number on a persistent part of the wlvif. This helps the data survive through recoveries/suspends, which also entail changes in the hlid of the link. This functionality is STA only currently. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: don't risk using stale HLID during .sta_state callbackArik Nemtsov1-4/+2
The HLID of a STA can change, particularly during recovery. Don't cache the HLID before it was potentially allocated. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: fix link count in single-link-PSM optimizationArik Nemtsov2-6/+14
commit 144614f3eebd7d only allowed a single active link when turning on the optimization, ignoring the fact that an AP has two additional global links. Use 3 links as an indication for a single active link. Use the FW PSM bits to verify the extra active link belongs to the AP role. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: set max num of Rx BA sessions per chipIgal Chernobelsky7-4/+11
Maximum number of supported RX BA sessions depends on chip type. wl18xx supports 5 RX BA sessions while wl12xx supports 3. Signed-off-by: Igal Chernobelsky <igalc@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-25wlcore: enter elp in force ps mode in 5msIgal Chernobelsky1-1/+3
It is requiered to enter sleep mode with smaller delay in forced PS mode. This fixes issue of testing force PS mode during VoIP traffic where packets are sent every 20ms. Chip never enters ps mode with default 30 ms delay in such test. Signed-off-by: Igal Chernobelsky <igalc@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2013-03-20iwlwifi: mvm: Add support for different ROC typesIlan Peer3-17/+24
Schedule different time event based on the ROC type Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20Merge remote-tracking branch 'wireless-next/master' into iwlwifi-nextJohannes Berg158-1297/+6525
2013-03-20iwlwifi: mvm: Increase the max remain on channel timeIlan Peer1-1/+1
Increase the maximal remain on channel time as longer remain on channel requests are handled by the FW using fragmented time events. This reduces the number of user/kernel space iterations during flows such as p2p_listen. In addition it is currently required for flows which require longer duration such as p2p_sd. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: fix WoWLAN RF-kill bugJohannes Berg1-7/+3
The RF-kill wakeup trigger flag is set in the wrong command, which means it won't work. Also fix the comment in the TCP wakeup trigger code -- the firmware was changed to look at all the different trigger flags. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: tune the move to static SMPS due to BT loadEmmanuel Grumbach1-1/+3
We should disable MIMO only if bt_traffic_load goes up to 3. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLVEmmanuel Grumbach5-11/+22
This is the right source of information for the valid Tx antennas, not the NVM. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: take the radio type / step / dash from TLVsEmmanuel Grumbach2-16/+19
This data should taken from TLVs and not from the NVM. This is true for the value written in CSR_HW_IF_CONFIG_REG too. Also, no need to set the CSR_HW_IF_CONFIG_REG_BIT_MAC_SI bit for 7000 devices which are the only devices currently supported. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: specify filter flags in monitor modeJohannes Berg1-1/+6
In firmware "listener" (monitor) mode, we still need to open up the filters with the filter flags to receive all frames. Reviewed-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: add debug message when a CMD is dropped in RFKILLEmmanuel Grumbach1-1/+4
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: print the flags in ALIVE notificationEmmanuel Grumbach1-2/+3
This has valuable data about RFkill state seen from the fw side. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: remove 5ghz_disable optionStanislaw Gruszka2-6/+0
5ghz_disable has no effect any longer, that was changed during refactoring of EEPROM reading/parsing. Remove it, wpa_supplicant allow now to specify frequencies, on which device will operate. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20iwlwifi: mvm: Fix quota handling for monitor interfaceIlan Peer3-3/+9
1. Quota for the monitor interface should be added only if there is a channel context assigned to the interface. 2. In the unassign channel context flow, need to remove the quota for the monitor interface binding, before unbinding. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-16 13:19:11 +0000