Age | Commit message (Collapse) | Author | Files | Lines |
|
legacy samsung gpio
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
commit a585f87c863e4e1d496459d382b802bf5ebe3717 upstream.
The scenario here is that someone calls enable_irq_wake() from somewhere
in the code. This will result in the lockdep producing a backtrace as can
be seen below. In my case, this problem is triggered when using the wl1271
(TI WlCore) driver found in drivers/net/wireless/ti/ .
The problem cause is rather obvious from the backtrace, but let's outline
the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(),
which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq()
calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to
grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in
irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not
marked as recursive, lockdep will spew the stuff below.
We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to
fix the spew.
=============================================
[ INFO: possible recursive locking detected ]
3.10.33-00012-gf06b763-dirty #61 Not tainted
---------------------------------------------
kworker/0:1/18 is trying to acquire lock:
(&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88
but task is already holding lock:
(&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by kworker/0:1/18:
#0: (events){.+.+.+}, at: [<c0036308>] process_one_work+0x134/0x4a4
#1: ((&fw_work->work)){+.+.+.}, at: [<c0036308>] process_one_work+0x134/0x4a4
#2: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88
stack backtrace:
CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 3.10.33-00012-gf06b763-dirty #61
Workqueue: events request_firmware_work_func
[<c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<c0011c74>] (show_stack+0x10/0x14)
[<c0011c74>] (show_stack+0x10/0x14) from [<c005bb08>] (__lock_acquire+0x140c/0x1a64)
[<c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<c005c6a8>] (lock_acquire+0x9c/0x104)
[<c005c6a8>] (lock_acquire+0x9c/0x104) from [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58)
[<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c00685f0>] (__irq_get_desc_lock+0x48/0x88)
[<c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<c0068e78>] (irq_set_irq_wake+0x20/0xf4)
[<c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24)
[<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<c0068cf4>] (set_irq_wake_real+0x30/0x44)
[<c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4)
[<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c)
[<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<c02be5e8>] (request_firmware_work_func+0x38/0x58)
[<c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<c0036394>] (process_one_work+0x1c0/0x4a4)
[<c0036394>] (process_one_work+0x1c0/0x4a4) from [<c0036a4c>] (worker_thread+0x138/0x394)
[<c0036a4c>] (worker_thread+0x138/0x394) from [<c003cb74>] (kthread+0xa4/0xb0)
[<c003cb74>] (kthread+0xa4/0xb0) from [<c000ee00>] (ret_from_fork+0x14/0x34)
wlcore: loaded
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c234962b808f289237a40e4ce5fc1c8066d1c9d0 upstream.
R-Car H1 or Gen2 GPIO interrupts are assigned per each GPIO domain,
but, Gen1 E1/M1 GPIO interrupts are shared for all GPIO domain.
gpio-rcar driver needs IRQF_SHARED flags for these.
This patch was tested on Bock-W board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4cc629b7a20945ce35628179180329b6bc9e552b upstream.
We should be writing bits here but instead we're writing the
numbers that correspond to the bits we want to write. Fix it by
wrapping the numbers in the BIT() macro. This fixes gpios acting
as interrupts.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5837ec11f8cfa6d53ebc5806582771b2c9988c6 upstream.
Commit 0b2aa8be introduced a regression that causes failure
in setting LED GPO direction to OUT.
This causes USB host probe failures for Beagleboard C4.
platform usb_phy_gen_xceiv.2: Driver usb_phy_gen_xceiv requests probe deferral
hsusb2_vcc: Failed to request enable GPIO510: -22
reg-fixed-voltage reg-fixed-voltage.0.auto: Failed to register regulator: -22
reg-fixed-voltage: probe of reg-fixed-voltage.0.auto failed with error -22
direction_out/direction_in must return 0 if the operation succeeded.
Also, don't update direction flag and output data if twl4030_set_gpio_direction()
failed inside twl_direction_out();
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1aeef303b5d9e243c41d5b80f8bb059366514a10 upstream.
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ba3154d9cb13697b97723cce75633b48adfe826 upstream.
The PL061 driver had the irqdomain initialization in an unfortunate
place: when used with device tree (and thus passing the base IRQ
0) the driver would work, as this registers an irqdomain and waits
for mappings to be done dynamically as the devices request their
IRQs, whereas when booting using platform data the irqdomain core
would attempt to allocate IRQ descriptors dynamically (which works
fine) but also to associate the irq_domain_associate_many() on all
IRQs, which in turn will call the mapping function which at this
point will try to set the type of the IRQ and then tries to acquire
a non-initialized spinlock yielding a backtrace like this:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.13.0-rc1+ #652
Backtrace:
[<c0016f0c>] (dump_backtrace) from [<c00172ac>] (show_stack+0x18/0x1c)
r6:c798ace0 r5:00000000 r4:c78257e0 r3:00200140
[<c0017294>] (show_stack) from [<c0329ea0>] (dump_stack+0x20/0x28)
[<c0329e80>] (dump_stack) from [<c004fa80>] (__lock_acquire+0x1c0/0x1b80)
[<c004f8c0>] (__lock_acquire) from [<c0051970>] (lock_acquire+0x6c/0x80)
r10:00000000 r9:c0455234 r8:00000060 r7:c047d798 r6:600000d3 r5:00000000
r4:c782c000
[<c0051904>] (lock_acquire) from [<c032e484>] (_raw_spin_lock_irqsave+0x60/0x74)
r6:c01a1100 r5:800000d3 r4:c798acd0
[<c032e424>] (_raw_spin_lock_irqsave) from [<c01a1100>] (pl061_irq_type+0x28/0x)
r6:00000000 r5:00000000 r4:c798acd0
[<c01a10d8>] (pl061_irq_type) from [<c0059ef4>] (__irq_set_trigger+0x70/0x104)
r6:00000000 r5:c01a10d8 r4:c046da1c r3:c01a10d8
[<c0059e84>] (__irq_set_trigger) from [<c005b348>] (irq_set_irq_type+0x40/0x60)
r10:c043240c r8:00000060 r7:00000000 r6:c046da1c r5:00000060 r4:00000000
[<c005b308>] (irq_set_irq_type) from [<c01a1208>] (pl061_irq_map+0x40/0x54)
r6:c79693c0 r5:c798acd0 r4:00000060
[<c01a11c8>] (pl061_irq_map) from [<c005d27c>] (irq_domain_associate+0xc0/0x190)
r5:00000060 r4:c046da1c
[<c005d1bc>] (irq_domain_associate) from [<c005d604>] (irq_domain_associate_man)
r8:00000008 r7:00000000 r6:c79693c0 r5:00000060 r4:00000000
[<c005d5d0>] (irq_domain_associate_many) from [<c005d864>] (irq_domain_add_simp)
r8:c046578c r7:c035b72c r6:c79693c0 r5:00000060 r4:00000008 r3:00000008
[<c005d814>] (irq_domain_add_simple) from [<c01a1380>] (pl061_probe+0xc4/0x22c)
r6:00000060 r5:c0464380 r4:c798acd0
[<c01a12bc>] (pl061_probe) from [<c01c0450>] (amba_probe+0x74/0xe0)
r10:c043240c r9:c0455234 r8:00000000 r7:c047d7f8 r6:c047d744 r5:00000000
r4:c0464380
This moves the irqdomain initialization to a point where the spinlock
and GPIO chip are both fully propulated, so the callbacks can be used
without crashes.
I had some problem reproducing the crash, as the devm_kzalloc():ed
zeroed memory would seemingly mask the spinlock as something OK,
but by poisoning the lock like this:
u32 *dum;
dum = (u32 *) &chip->lock;
*dum = 0xaaaaaaaaU;
I could reproduce, fix and test the patch.
Reported-by: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c8aab8e65e450f2bfea494c1b6a86ded653f88c upstream.
It's not obvious from the label name but "err1" tries to release
"p->irq_domain" which leads to a NULL dereference.
Fixes: 119f5e448d32 ('gpio: Renesas R-Car GPIO driver V3')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d535922691fc026479fcc03e78ac3d931a54e75a upstream.
There is a bug in mvebu_gpio_probe() where we do:
mvchip->irqbase = irq_alloc_descs(-1, 0, ngpios, -1);
if (mvchip->irqbase < 0) {
The problem is that mvchip->irqbase is unsigned so the error handling
doesn't work. I have changed it to be a regular int.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b2aa8bed3e13892fcac77e4f50ec6e80125469d upstream.
Commit c111feabe2e2 (gpio: twl4030: Cache the direction and output
states in private data) improved things in general, but caused a
regression for setting the GPIO output direction.
The change reorganized twl_direction_out() and twl_set() and swapped
the function names around in the process. While doing that, a bug got
introduced that's not obvious while reading the patch as it appears
as no change to the code.
The bug is we now call function twl4030_set_gpio_dataout() twice in
both twl_direction_out() and twl_set(). Instead, we should first
call twl_direction_out() in twl_direction_out() followed by
twl4030_set_gpio_dataout() in twl_set().
This regression probably has gone unnoticed for a long time as the
bootloader may have set the GPIO direction properly in many cases.
This fixes at least the LCD panel not turning on omap3 LDP for
example.
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03d152d5582abc8a1c19cb107164c3724bbd4be4 upstream.
Checking LP_INT_STAT is not enough in the interrupt handler because its
contents get updated regardless of whether the pin has interrupt enabled or
not. This causes the driver to loop forever for GPIOs that are pulled up.
Fix this by checking the interrupt enable bit for the pin as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fac7fa162a19100298d5d91359960037dc5bfca9 upstream.
The OMAP GPIO controller HW requires a pin to be configured in GPIO
input mode in order to operate as an interrupt input. Since drivers
should not be aware of whether an interrupt pin is also a GPIO or not,
the HW should be fully configured/enabled as an IRQ if a driver solely
uses IRQ APIs such as request_irq(), and never calls any GPIO-related
APIs. As such, add the missing HW setup to the OMAP GPIO controller's
irq_chip driver.
Since this bypasses the GPIO subsystem we have to ensure that another
driver won't be able to request the same GPIO pin that is used as an
IRQ and set its direction as output. Requesting the GPIO and setting
its direction as input is allowed though.
This fixes smsc911x ethernet support for tobi and igep OMAP3 boards
and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line.
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa365e4d729065b5e85165df3dc9699ed47489cc upstream.
The GPIO OMAP controller pins can be used as IRQ and GPIO
independently so is necessary to keep track GPIO pins and
IRQ lines usage separately to make sure that the bank will
always be enabled while being used.
Also move gpio_is_input() definition in preparation for the
next patch that setups the controller's irq_chip driver when
a caller requests an interrupt line.
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ede4d7a5 ("gpio/omap: convert gpio irq domain to linear mapping")
converted the OMAP GPIO driver to use a linear mapping for the GPIO IRQ
domain instead of using a legacy mapping. Not using a legacy mapping has
a number of benefits but it requires the platform to support SPARSE_IRQ
which currently is not supported on OMAP1.
So this change caused a regression on OMAP1 platforms [1].
Since this issue is not present on all OMAP2+ platforms, there is no need to
revert the driver to use legacy domain mapping for all the platforms.
[1]: http://www.mail-archive.com/linux-omap@vger.kernel.org/msg89005.html
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- An OMAP fix that makes ethernet work again.
- Fix for build problem when building the MCP23S08 driver as module.
- IRQ conflicts in the Langwell driver.
- Fix IRQ coherency issues in the MXS driver.
- Return correct errorcode on errorpath when removing GPIO chips.
* tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Don't override the error code in probe error handling
gpio: mxs: Use set and clear capabilities of the gpio controller
gpio-langwell: fix irq conflicts when DT is not used
gpio: mcp23s08: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
gpio/omap: ensure gpio context is initialised
|
|
Otherwise, we return 0 in probe error paths when gpiochip_remove() returns 0.
Also show error message if gpiochip_remove() fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: Denis Turischev <denis@compulab.co.il>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current driver doesn't use the set and clear registers found on the
mxs gpio controller.
This leads the generic gpio controller to be using some internal value
to avoid looking up the value stored in the registers, making it behave
pretty much like a cache.
This raises some coherency problem when a gpio is not modified by the
gpio controller, while it can easily be fixed by using the set and clear
registers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When DT is not used IOAPIC does not register irq domain. As result
IOAPIC won't care about gpio-langwell's virq and may cause conflict if
an irq number is equal to gpio-langwell's virq mapped beforehand.
This patch tells gpio_langwell to not ignore irq_base if != 0 and
preferably use it to avoid the conflict.
If DT is used, irq_base can safely be 0.
Signed-off-by: David Cohen <david.a.cohen@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes below build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m &&
CONFIG_GPIO_MCP23S08=y.
LD init/built-in.o
drivers/built-in.o: In function `mcp23017_write':
clkdev.c:(.text+0x1e14): undefined reference to `i2c_smbus_write_word_data'
drivers/built-in.o: In function `mcp23017_read':
clkdev.c:(.text+0x1e24): undefined reference to `i2c_smbus_read_word_data'
drivers/built-in.o: In function `mcp23008_write':
clkdev.c:(.text+0x1e8c): undefined reference to `i2c_smbus_write_byte_data'
drivers/built-in.o: In function `mcp23008_read':
clkdev.c:(.text+0x1e98): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mcp23008_read_regs':
clkdev.c:(.text+0x1ed0): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mcp23s08_init':
clkdev.c:(.init.text+0x30): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `mcp23s08_exit':
clkdev.c:(.exit.text+0x30): undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1
When CONFIG_I2C=m, meaning we can't build the drivers in with I2C support.
Thus don't allow the drivers to be compiled as built-in when CONFIG_I2C=m.
The real fix though is to break the driver apart into a SPI part, an I2C part
and a common part. But that's something for 3.11 while this is something for
3.10/stable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
Commit a2797be (gpio/omap: force restore if context loss is not
detectable) broke gpio support for OMAP when booting with device-tree
because a restore of the gpio context being performed without ever
initialising the gpio context. In other words, the context restored was
bad.
This problem could also occur in the non device-tree case, however, it
is much less likely because when booting without device-tree we can
detect context loss via a platform specific API and so context restore
is performed less often.
Nevertheless we should ensure that the gpio context is initialised
on the first pm-runtime resume for gpio banks that could lose their
state regardless of whether we are booting with device-tree or not.
The context loss count was being initialised on the first pm-runtime
suspend following a resume, by populating the get_count_loss_count()
function pointer after the first pm-runtime resume. To make the code
more readable and logical, initialise the context loss count on the
first pm-runtime resume if the context is not yet valid.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar<santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
|
|
Pull GPIO changes from Grant Likely:
"The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support"
I'm pulling this despite the earlier mess. Let's hope it compiles these
days.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (46 commits)
gpio: grgpio: Add irq support
gpio: grgpio: Add device driver for GRGPIO cores
gpiolib-acpi: introduce acpi_get_gpio_by_index() helper
GPIO: gpio-generic: remove kfree() from bgpio_remove call
gpio / ACPI: Handle ACPI events in accordance with the spec
gpio: lpc32xx: Fix off-by-one valid range checking for bank
gpio: mcp23s08: convert driver to DT
gpio/omap: force restore if context loss is not detectable
gpio/omap: optimise interrupt service routine
gpio/omap: remove extra context restores in *_runtime_resume()
gpio/omap: free irq domain in probe() failure paths
gpio: gpio-generic: Add 16 and 32 bit big endian byte order support
gpio: samsung: Add terminating entry for exynos_pinctrl_ids
gpio: mvebu: add dbg_show function
MAX7301 GPIO: Do not force SPI speed when using OF Platform
gpio: gpio-tps65910.c: fix checkpatch error
gpio: gpio-timberdale.c: fix checkpatch error
gpio: gpio-tc3589x.c: fix checkpatch errors
gpio: gpio-stp-xway.c: fix checkpatch error
gpio: gpio-sch.c: fix checkpatch error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For 3.10 we have a few new MFD drivers for:
- The ChromeOS embedded controller which provides keyboard, battery
and power management services. This controller is accessible
through i2c or SPI.
- Silicon Laboratories 476x controller, providing access to their FM
chipset and their audio codec.
- Realtek's RTS5249, a memory stick, MMC and SD/SDIO PCI based
reader.
- Nokia's Tahvo power button and watchdog device. This device is
very similar to Retu and is thus supported by the same code base.
- STMicroelectronics STMPE1801, a keyboard and GPIO controller
supported by the stmpe driver.
- ST-Ericsson AB8540 and AB8505 power management and voltage
converter controllers through the existing ab8500 code.
Some other drivers got cleaned up or improved. In particular:
- The Linaro/STE guys got the ab8500 driver in sync with their
internal code through a series of optimizations, fixes and
improvements.
- The AS3711 and OMAP USB drivers now have DT support.
- The arizona clock and interrupt handling code got improved.
- The wm5102 register patch and boot mechanism also got improved."
* tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (104 commits)
mfd: si476x: Don't use 0bNNN
mfd: vexpress: Handle pending config transactions
mfd: ab8500: Export ab8500_gpadc_sw_hw_convert properly
mfd: si476x: Fix i2c warning
mfd: si476x: Add header files and Kbuild plumbing
mfd: si476x: Add chip properties handling code
mfd: si476x: Add the bulk of the core driver
mfd: si476x: Add commands abstraction layer
mfd: rtsx: Support RTS5249
mfd: retu: Add Tahvo support
mfd: ucb1400: Pass ucb1400-gpio data through ac97 bus
mfd: wm8994: Add some OF properties
mfd: wm8994: Add device ID data to WM8994 OF device IDs
input: Export matrix_keypad_parse_of_params()
mfd: tps65090: Add compatible string for charger subnode
mfd: db8500-prcmu: Support platform dependant device selection
mfd: syscon: Fix warnings when printing resource_size_t
of: Add stub of_get_parent for non-OF builds
mfd: omap-usb-tll: Convert to devm_ioremap_resource()
mfd: omap-usb-host: Convert to devm_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes (part 1) from Olof Johansson:
"These changes are all for board specific files. These used to make up
a large portion of the ARM changes in the past, but as we are
generalizing the support and moving to device tree probing, this has
gotten significantly smaller.
The only platform actually adding new code here at the moment is
Renesas shmobile, as they are still busy converting their code to
device tree and have not come far enough to not need it."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: msm: USB_MSM_OTG needs USB_PHY
ARM: davinci: da850 evm: fix const qualifier placement
ARM: davinci: da850 board: add remoteproc support
ARM: pxa: move debug uart code
ARM: pxa: select PXA935 on saar & tavorevb
ARM: mmp: add more compatible names in gpio driver
ARM: pxa: move PXA_GPIO_TO_IRQ macro
ARM: pxa: remove cpu_is_xxx in gpio driver
ARM: Kirkwood: update Network Space Mini v2 description
ARM: Kirkwood: DT board setup for CloudBox
ARM: Kirkwood: sort board entries by ASCII-code order
ARM: OMAP: board-4430sdp: Provide regulator to pwm-backlight
ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
ARM: OMAP2+: omap2plus_defconfig: Add support for BMP085 pressure sensor
omap2+: Remove useless Makefile line
omap2+: Remove useless Makefile line
ARM: OMAP: RX-51: add missing regulator supply definitions for lis3lv02d
ARM: OMAP1: fix omap_udc registration
ARM: davinci: use is IS_ENABLED macro
ARM: kirkwood: add MACH_GURUPLUG_DT to defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"This branch contains part 1 of the platform updates for 3.10. Among
the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (135 commits)
ARM: tegra: pm: fix build error w/o PM_SLEEP
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
ARM: socfpga: Upgrade clk driver for socfpga to make use of dts clock entries
ARM: socfpga: Add clock entries into device tree
ARM: socfpga: Enable soft reset
ARM: EXYNOS: replace cpumask by the corresponding macro
ARM: EXYNOS: handle properly the return values
ARM: EXYNOS: factor out the idle states
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
ARM: tegra: pm: remove duplicated include from pm.c
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: SAMSUNG: check processor type before cache restoration in resume
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl update from Linus Walleij:
"These are the pinctrl changes for v3.10:
- Patrice Chotard contributed a new configuration debugfs interface
and reintroduced fine-grained locking into the core: instead of
having a "big pinctrl lock" we have a per-controller lock and
specialized locks for the global controller and pinctrl handle
lists.
- Haoijan Zhuang deleted all the PXA and MMP2 pinctrl drivers and
replaced them with pinctrl-single (which is also used by other
SoCs) so we are gaining consolidation. The platform particulars
now come in through the device tree.
- Haoijan also added support for generic pin config into the
pinctrl-single driver which is another big consolidation win.
- Finally also GPIO ranges are now supported by the pinctrl-single
driver.
- Tomasz Figa contributed a new Samsung S3C pinctrl driver, bringing
more of the older Samsung platforms under the pinctrl umbrella and
out of arch/arm.
- Maxime Ripard contributed new Allwinner A10/A13 drivers.
- Sachin Kamat, Wei Yongjun and Axel Lin did a lot of cleanups."
* tag 'pinctrl-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (66 commits)
pinctrl: move subsystem mutex to pinctrl_dev struct
pinctrl/pinconfig: fix misplaced goto
pinctrl: s3c64xx: Fix build error caused by undefined chained_irq_enter
pinctrl/pinconfig: add debug interface
pinctrl: abx500: fix issue when no pdata
pinctrl: pinctrl-single: add missing double quote
pinctrl: sunxi: Rename wemac functions to emac
pinctrl: exynos5440: add gpio interrupt support
pinctrl: exynos5440: fix probe failure due to missing pin-list in config nodes
pinctrl: ab8505: Staticize some symbols
pinctrl: ab8540: Staticize some symbols
pinctrl: ab9540: Staticize some symbols
pinctrl: ab8500: Staticize some symbols
pinctrl: abx500: Staticize some symbols
pinctrl: Add pinctrl-s3c64xx driver
pinctrl: samsung: Handle banks with two configuration registers
pinctrl: samsung: Remove hardcoded register offsets
pinctrl: samsung: Split pin bank description into two structures
pinctrl: samsung: Include pinctrl-exynos driver data conditionally
pinctrl: samsung: Protect bank registers with a spinlock
...
|
|
Merge in the gic cleanup since it has a handful of annoying internal conflicts
with soc development branches. All of them are delete/delete conflicts.
* gic/cleanup:
irqchip: vic: add include of linux/irq.h
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-shmobile/smp-emev2.c
arch/arm/mach-shmobile/smp-r8a7779.c
arch/arm/mach-shmobile/smp-sh73a0.c
arch/arm/mach-socfpga/platsmp.c
|
|
Merging in fixes since there's a conflict in the omap4 clock tables caused by
it.
* fixes: (245 commits)
ARM: highbank: fix cache flush ordering for cpu hotplug
ARM: OMAP4: hwmod data: make 'ocp2scp_usb_phy_phy_48m" as the main clock
arm: mvebu: Fix the irq map function in SMP mode
Fix GE0/GE1 init on ix2-200 as GE0 has no PHY
ARM: S3C24XX: Fix interrupt pending register offset of the EINT controller
ARM: S3C24XX: Correct NR_IRQS definition for s3c2440
ARM i.MX6: Fix ldb_di clock selection
ARM: imx: provide twd clock lookup from device tree
ARM: imx35 Bugfix admux clock
ARM: clk-imx35: Bugfix iomux clock
+ Linux 3.9-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-omap2/cclock44xx_data.c
|
|
This merges in the revert of multiplatform support for exynos.
Trivial conflicts on removed code. Also, needed to add "select COMMON_CLK"
to the non-multiplatform EXYNOS config option.
* samsung/exynos-multiplatform:
Revert "ARM: exynos: enable multiplatform support"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit bd51de53e1be9896d815bbea30560262216d4616.
Turns out that multiplatform breaks some uses cases, such as when you
have an existing defconfig, since it adds the new EXYNOS_SINGLE config
option as a dependecy. As a result, nearly all exynos config options
will be disabled by default.
Reverting instead of rebasing since this branch is pulled in as a
dependency elsewhere.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The drivers sets up an irq domain and hands out unique irqs to irq
capable gpio lines regardless of how underlying irq maps to gpio
lines. Any gpio line can map to any one or none of the irqs of the
core, independently of each other.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver supports GRGPIO gpio cores available in the GRLIB VHDL IP
core library from Aeroflex Gaisler.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 6c7e660a27da7494c670bfba21cfeba30457656c.
The commit causes breakage on several older PXA machines.
Reported-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Merging this into the next/drivers branch avoids a number of
pointless conflicts with code changed here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This makes it possible to enable the exynos platform as part of a
multiplatform kernel, in addition to keeping the single-platform
exynos support.
The multiplatform variant has a number of limitations at the moment:
* It only supports DT-enabled machines. This is not a problem in
the long run, as non-DT machines for exynos are going away.
The main problem here is that the gpio code and the exynos_eint
irqchip are not multiplatform capable but still required for
ATAGS based boot.
* The watchdog driver is still missing a conversion.
* sparsemem and memory_holes are currently not supported in
multiplatform.
The the multiplatform aware ARCH_EXYNOS Kconfig symbol is disabled
for now, as dependent patches are still pending in other
subsystem trees. We will enable it once everything comes together.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
GENERIC_GPIO has been made equivalent to GPIOLIB in architecture code
and all driver code has been switch to depend on GPIOLIB. It is thus
safe to have GENERIC_GPIO removed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
Cleanups for MSM for 3.10
These are some patches for various parts of MSM that gradually bring
us closer to being part of single zimage.
* tag 'msm-cleanup-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Remove unused cpu.h header file
gpio: Make gpio-msm-v1 into a platform driver
mmc: msm_sdcc: Remove unnecessary include
ARM: msm: Move dma.h #defines that are private to dma.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Instead of open-coding ACPI GPIO resource lookup in each driver, we provide
a helper function analogous to Device Tree version that allows drivers to
specify which GPIO resource they are interested (using an index to the GPIO
resources). The function then finds out the correct resource, translates
the ACPI GPIO number to the corresponding Linux GPIO number and returns
that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Memory for basic-mmio-gpio driver is allocated by the driver
using it, whether it's the generic GPIO driver itself or another
driver. In either case, the owner shall allocate and free the
struct bgpio_chip it is using, preferably using a managed
resource.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We actually have to pass chip as the host_data parameter of
irq_domain_add_simple() as later on, it is used to initialize chip_data
in pca953x_gpio_irq_map(). Failing to do so is leading to a NULL pointer
dereference after calling irq_data_get_irq_chip_data() in
pca953x_irq_mask(), pca953x_irq_unmask(), pca953x_irq_bus_lock(),
pca953x_irq_bus_sync_unlock() and pca953x_irq_set_type().
Fixes regression introduced by commit
0e8f2fdacf1d44651aa7e57063c76142d1f4988b (gpio: pca953x: use simple
irqdomain)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A series dealing with gpio configuration cleanup from Haojian Zhuang.
* 'armsoc/pxa' of git://github.com/hzhuang1/linux:
ARM: pxa: move debug uart code
ARM: pxa: select PXA935 on saar & tavorevb
ARM: mmp: add more compatible names in gpio driver
ARM: pxa: move PXA_GPIO_TO_IRQ macro
ARM: pxa: remove cpu_is_xxx in gpio driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since more driver names are added into platform id, do the same thing on
compatible names for DT mode.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since PXA_GPIO_TO_IRQ() & MMP_GPIO_TO_IRQ() macro are depended on
arch code, move them from gpio driver to platform driver instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Avoid to use cpu_is_xxx() in pxa gpio driver. Use platform_device_id
to identify the difference.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 0d1c28a (gpiolib-acpi: Add ACPI5 event model support to gpio.)
that added support for ACPI events signalled through GPIO interrupts
covered only GPIO pins whose numbers are less than or equal to 255.
However, there may be GPIO pins with numbers greater than 255 and
the ACPI spec (ACPI 5.0, Section 5.6.5.1) requires the _EVT method
to be used for handling events corresponding to those pins.
Moreover, according to the spec, _EVT is the default mechanism
for handling all ACPI events signalled through GPIO interrupts,
so if the _Exx/_Lxx method is not present for the given pin,
_EVT should be used instead. If present, though, _Exx/_Lxx take
precedence over _EVT which shouldn't be executed in that case
(ACPI 5.0, Section 5.6.5.3).
Modify acpi_gpiochip_request_interrupts() to follow the spec as
described above and add acpi_gpiochip_free_interrupts() needed
to free interrupts associated with _EVT.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|