| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* 'samsung-fixes-4' of git://github.com/kgene/linux-samsung:
ARM: S3C24XX: Fix s3c24xx build errors if !CONFIG_PM
ARM: S5P: fix offset calculation on gpio-interrupt
|
|
This allows mapping external memory such as SRAM for use.
This is needed for some small chunks of code, such as reprogramming
SDRAM memory source clocks that can't be executed in SDRAM. Other
use cases include some PM related code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If two requests have been submitted and one of them is running, if you
call pl330_chan_ctrl(ch_id, PL330_OP_START), there's a window of time
between the spin_lock_irqsave() and the _state() check in which the
running transaction may finish. In that case, we don't receive the
interrupt (because they are disabled), but _start() sees that the DMA
is stopped, so it starts it. The problem is that it sends the
transaction that has just finished again, because pl330_update()
hasn't mark it as done yet.
This patch fixes this race condition by not calling _start() if the
DMA is already executing transactions. When interrupts are reenabled,
pl330_update() will call _start().
Reference: <1317892206-3600-1-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* pm-domains:
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
|
|
This change adds support for the sh7372 A4R power domain.
The sh7372 A4R hardware power domain contains the
SH CPU Core and a set of I/O devices including
multimedia accelerators and I2C controllers.
One special case about A4R is the INTCS interrupt
controller that needs to be saved and restored to
keep working as expected. Also the LCDC hardware
blocks are in a different hardware power domain
but have their IRQs routed only through INTCS. So
as long as LCDCs are active we cannot power down
INTCS because that would risk losing interrupts.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This change adds support for the sh7372 A3SP power domain.
The sh7372 A3SP hardware power domain contains a
wide range of I/O devices. The list of I/O devices
include SCIF serial ports, DMA Engine hardware,
SD and MMC controller hardware, USB controllers
and I2C master controllers.
This patch adds the A3SP low level code which
powers the hardware power domain on and off. It
also ties in platform devices to the pm domain
support code.
It is worth noting that the serial console is
hooked up to SCIFA0 on most sh7372 boards, and
the SCIFA0 port is included in the A3SP hardware
power domain. For this reason we cannot output
debug messages from the low level power control
code in the case of A3SP.
QoS support is needed in drivers before we can
enable the A3SP power control on the fly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue
v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Offsets of the irq controller registers were calculated
correctly only for first GPIO bank. This patch fixes
calculation of the register offsets for all GPIO banks.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Upon adding new board LL debug support, if the resultant code
addition would not cause PC relative offset of "hexbuf" from
"adr r2, hexbuf" (+2) instruction to be representable in a
shifted 8-bit value (hence indirectly putting higher aligment
requirement on larger offsets), following error occurs,
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:138: Error: invalid constant (428) after fixup
Fix it by bringing "hexbuf" closer so that "adr"
can have the offset.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Add alignment flag to PCI expansion resources
sparc: Avoid calling sigprocmask()
sparc: Use set_current_blocked()
sparc32,leon: SRMMU MMU Table probe fix
|
|
Currently no type of alignment is specified for PCI expansion roms while
parsing the openfirmware tree. This causes calls to pci_map_rom() to fail.
IORESOURCE_SIZEALIGN is the default alignment used for rom resouces in
pci/probe.c, and has been verified to work with various cards on a ultra 10.
Signed-off-By: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per Ian Campbell suggestion to defend against future breakage
in case we expand the P2M values, incorporate the defines
in the string array.
Suggested-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
We could be referencing the last + 1 element of level_name[]
array which would cause a pointer exception, because of the
initial setup of lvl=4.
[v1: No need to do this for type_name, pointed out by Ian Campbell]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
We get:
linux/arch/x86/xen/enlighten.c: In function ‘xen_start_kernel’:
linux/arch/x86/xen/enlighten.c:226: warning: ‘cx’ may be used uninitialized in this function
linux/arch/x86/xen/enlighten.c:240: note: ‘cx’ was declared here
and the cx is really not set but passed in the xen_cpuid instruction
which masks the value with returned masked_ecx from cpuid. This
can potentially lead to invalid data being stored in cx.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
There are three different modes: PV, HVM, and initial domain 0. In all
the cases we would return -1 for failure instead of a proper error code.
Fix this by propagating the error code from the generic IRQ code.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
commit ab4382d27412e7e3e7c936e8d50d8888dfac3df8 moved
drivers/serial/Kconfig to drivers/tty/serial/Kconfig, so we need to
source the latter file.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When compiling an i386_defconfig kernel with
gcc-4.6.1-9.fc15.i686, I noticed a warning about the asm operand
for test_bit in kprobes' can_boost. I discovered that this
caused only the first long of twobyte_is_boostable[] to be
output.
Jakub filed and fixed gcc PR50571 to correct the warning and
this output issue. But to solve it for less current gcc, we can
make kprobes' twobyte_is_boostable[] volatile, and it won't be
optimized out.
Before:
CC arch/x86/kernel/kprobes.o
In file included from include/linux/bitops.h:22:0,
from include/linux/kernel.h:17,
from [...]/arch/x86/include/asm/percpu.h:44,
from [...]/arch/x86/include/asm/current.h:5,
from [...]/arch/x86/include/asm/processor.h:15,
from [...]/arch/x86/include/asm/atomic.h:6,
from include/linux/atomic.h:4,
from include/linux/mutex.h:18,
from include/linux/notifier.h:13,
from include/linux/kprobes.h:34,
from arch/x86/kernel/kprobes.c:43:
[...]/arch/x86/include/asm/bitops.h: In function ‘can_boost.part.1’:
[...]/arch/x86/include/asm/bitops.h:319:2: warning: use of memory input without lvalue in asm operand 1 is deprecated [enabled by default]
$ objdump -rd arch/x86/kernel/kprobes.o | grep -A1 -w bt
551: 0f a3 05 00 00 00 00 bt %eax,0x0
554: R_386_32 .rodata.cst4
$ objdump -s -j .rodata.cst4 -j .data arch/x86/kernel/kprobes.o
arch/x86/kernel/kprobes.o: file format elf32-i386
Contents of section .data:
0000 48000000 00000000 00000000 00000000 H...............
Contents of section .rodata.cst4:
0000 4c030000 L...
Only a single long of twobyte_is_boostable[] is in the object
file.
After, with volatile:
$ objdump -rd arch/x86/kernel/kprobes.o | grep -A1 -w bt
551: 0f a3 05 20 00 00 00 bt %eax,0x20
554: R_386_32 .data
$ objdump -s -j .rodata.cst4 -j .data arch/x86/kernel/kprobes.o
arch/x86/kernel/kprobes.o: file format elf32-i386
Contents of section .data:
0000 48000000 00000000 00000000 00000000 H...............
0010 00000000 00000000 00000000 00000000 ................
0020 4c030000 0f000200 ffff0000 ffcff0c0 L...............
0030 0000ffff 3bbbfff8 03ff2ebb 26bb2e77 ....;.......&..w
Now all 32 bytes are output into .data instead.
Signed-off-by: Josh Stone <jistone@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Link: http://lkml.kernel.org/r/1318899645-4068-1-git-send-email-jistone@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Create common extern definitions of _rambase, _ramstart and _ramend
instead of them being externed when used in code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
We do not need to have local extern declarations of memory_start and
memory_end in mm/init_no.c. There are declarations already in asm/page_no.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
We should be including and using sections.h to get at the extern
definitions of the linker sections in the m68knommu mm init code.
Not defining them locally.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
We should be including and using sections.h to get at the extern
definitions of the linker sections in the m68knommu startup code.
Not defining them locally.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The code for handling traps in the non-mmu case is a subset of the mmu
enabled case. Merge the non-mmu traps_no.c code back to a single traps.c.
There is actually no code mmu specific here at all, and the processor
specific code (for the more complex 68020/68030/68040/68060) is already
proplerly conditionaly used.
The format of console exception dump is a little different, but I don't
think will cause any one problems, it is purely for debug purposes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Most of the trap.c code is general to all m68k arch members. But the code
it currently contains to set the hardware vector table is quite specific to
the 680x0 family. They can have the vector table at any address unlike
other family members (which either support only a single fixed address,
or a limited range of addresses). So lets move that code out to a new file,
vectors.c. This will make sharing the rest of the trap.c code easier and
cleaner.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The changes in the mmu version of entry.h (entry_mm.h) and the non-mmu
version (entry_no.h) are not about the presence or use of an MMU at all.
The main changes are to support the ColdFire processors. The code for
trap entry and exit for all types of 68k processor outside coldfire is
the same.
So merge the files back to a single entry.h and share the common 68k
entry/exit code. Some changes are required for the non-mmu entry
handlers to adopt the differing macros for system call and interrupt
entry, but this is quite strait forward. The changes for the ColdFire
remove a couple of instructions for the separate a7 register case, and
are no worse for the older single a7 register case.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The few differences between the mmu and non-mmu kernel/Makefiles can
easily be handled inside of a single Makefile. Merge the 2 back into
a single Makefile.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
|
|
Most of the build logic is the same for the mmu and non-mmu m68k targets.
Merge the top level architecture Makefiles back into a single Makefile.
For the most part this is just adding the non-mmu processor types and
their specific cflags and other options into the mmu Makefile.
Note that all the BOARD setting logic that was in the non-mmu Makefile
is completely removed. It was no longer being used at all.
This has been build and run tested on ColdFire targets and ARAnyM.
It has been build tested on all the m68k defconfig targets using a
gcc-4.5.1 based toolchain.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
|
|
The current mmu and non-mmu Kconfig files can be merged to form
a more general selection of options. The current break up of options
is due to the simple brute force merge from the m68k and m68knommu
arch directories.
Many of the options are not at all specific to having the MMU enabled
or not. They are actually associated with a particular CPU type or
platform type.
Ultimately as we support all processors with the MMU disabled we need
many of these options to be selectable without the MMU option enabled.
And likewise some of the ColdFire processors, which currently are only
supported with the MMU disabled, do have MMU hardware, and will need
to have options selected on CPU type, not MMU disabled.
This patch removes the old mmu and non-mmu Kconfigs and instead breaks
up the configuration into four areas: cpu, machine, bus, devices.
The Kconfig.cpu lists all the options associated with selecting a CPU,
and includes options specific to each CPU type as well.
Kconfig.machine lists all options associated with selecting a machine
type. Almost always the machines selectable is restricted by the chosen
CPU.
Kconfig.bus contains options associated with selecting bus types on the
various machine types. That includes PCI bus, PCMCIA bus, etc.
Kconfig.devices contains options for drivers and driver associated
options.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The problem has its root in the calculation of the set-port offsets (macro
MCFGPIO_SETR() in arch/m68k/include/asm/gpio.h), this assumes that all ports
have the same offset from the base port address (MCFGPIO_SETR) which is
defined in mcf520xsim.h as an alias of MCFGIO_PSETR_BUSCTL. Because the BUSCTL
and BE port do not have a set-register (see MCF5208 Reference Manual Page
13-10, Table 13-3) the offset calculations went wrong.
Because the BE and BUSCTL port do not seem useful in these parts, as they
lack a set register, I removed them and adapted the gpio chip bases which
are also used for the offset-calculations. Now both setting and resetting
the chip selects works as expected from userland and from the kernelspace.
Signed-off-by: Peter Turczak <peter@turczak.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The original 68000 processors cannot copy 16bit or larger quantities from
odd addresses. All newer members of the 68k family (including ColdFire)
can do this.
In the current memcpy implementation after trying to align the destination
address to a 16bit boundary if we end up with an odd source address we go
off and try to copy multi-byte quantities from it. This will trap on the
68000.
The only solution if we end with an odd source address is to byte wise
copy the whole memcpy region. We only need to do this if we are supporting
original 68000 processors.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Atomic64 is now a valid type in Linux. Archs that do not have their own
version of atomic64 operators are to use the generic operations.
The m32r architecture needs to define GENERIC_ATOMIC64.
Link: http://lkml.kernel.org/r/20111013085936.GA13046@elte.hu
Link: http://lkml.kernel.org/r/1318516816.12224.12.camel@gandalf.stny.rr.com
Link: http://lkml.kernel.org/r/20111017185440.GB5545@elte.hu
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: David Rientjes <rientjes@google.com>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Add vision_ep9307, rwi_ews, usb_a9g20, karo, apf9328, tx37, tx25,
tx51, mx51_m2id, pca101, gplugd, smdk4212 and smdk4412.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a private iommu pointer to the ARM-specific arch data in the
device struct, which will be used to attach iommu-specific data
to devices which require iommu support.
Different iommu implementations (on different platforms) will attach
different types of data to this pointer, so 'void *' is currently used
(the downside is reduced typesafety).
Note: ia64, x86 and sparc have this exact iommu extension as well, and
if others are likely to adopt it too, we might want to consider
adding this to the device struct itself directly.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The 64bit division functions never had unwinding annotations
added. This prevents a backtrace from being printed within
the function and if a division by 0 occurs. Add the annotations.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Get rid of this complaint from dash:
AS arch/arm/boot/compressed/lib1funcs.o
/bin/sh: 1: [: y: unexpected operator
LD arch/arm/boot/compressed/vmlinux
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This resolves the following sparse warning from readl() and other macros,
which ends up embedding readl_relaxed() using the same variable.
arch/arm/mach-tegra/dma.c:169:8: warning: symbol '__v' shadows an earlier one
arch/arm/mach-tegra/dma.c:169:8: originally declared here
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This exposes the PB1176 ROM if you compile in the MTD physmap
mapping and also the map_rom chiptype.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This copy really don't need to do at the very second before the kernel
would crash.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Cache Type Register L1Ip field identifies I-caches with a PIPT
policy using the encoding 11b.
This patch extends the cache policy parsing to identify PIPT I-caches
correctly and prevent them from being treated as VIPT aliasing in cases
where they are sufficiently large.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Get rid of the mdesc pointer in the fixup function call. No one uses
the mdesc pointer, it shouldn't be modified anyway, and we can't wrap
it, so let's remove it.
Platform files found by:
$ regexp=$(git grep -h '\.fixup.*=' arch/arm |
sed 's!.*= *\([^,]*\),* *!\1!' | sort -u |
tr '\n' '|' | sed 's,|$,,;s,|,\\|,g')
$ git grep $regexp arch/arm
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ARM uses its own BUG() handler which makes its output slightly different
from other archtectures.
One of the problems is that the ARM implementation doesn't report the function
with the BUG() in it, but always reports the PC being in __bug(). The generic
implementation doesn't have this problem.
Currently we get something like:
kernel BUG at fs/proc/breakme.c:35!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at __bug+0x20/0x2c
With this patch it displays:
kernel BUG at fs/proc/breakme.c:35!
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP
...
PC is at write_breakme+0xd0/0x1b4
This implementation uses an undefined instruction to implement BUG, and sets up
a bug table containing the relevant information. Many versions of gcc do not
support %c properly for ARM (inserting a # when they shouldn't) so we work
around this using distasteful macro magic.
v1: Initial version to replace existing ARM BUG() implementation with something
more similar to other architectures.
v2: Add Thumb support, remove backtrace whitespace output changes. Change to
use macros instead of requiring the asm %d flag to work (thanks to
Dave Martin <dave.martin@linaro.org>)
v3: Remove old BUG() implementation in favor of this one.
Remove the Backtrace: message (will submit this separately).
Use ARM_EXIT_KEEP() so that some architectures can dump exit text at link time
thanks to Stephen Boyd <sboyd@codeaurora.org> (although since we always
define GENERIC_BUG this might be academic.)
Rebase to linux-2.6.git master.
v4: Allow BUGS in modules (these were not reported correctly in v3)
(thanks to Stephen Boyd <sboyd@codeaurora.org> for suggesting that.)
Remove __bug() as this is no longer needed.
v5: Add %progbits as the section flags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update the Integrator defconfig with some sensible defaults:
- Compile a combined image supporting Integrator/AP and
Integrator/CP, with the core modules CM720, CM920, CM922,
CM926, CM1020, CM1022 and CM1026 in a single image, this
works just fine and gives some nice compilation coverage
- NOHZ (tickless) and HRTIMERS turned on
- Compile using EABI, let's assume recent compilers are used
now (tested using GCC 4.4.1)
- Remove forced 32MiB at command line, the bootloader usually
knows this better, and my U-Boot patches nowadays make that
boot loader pass the correct adjusted value
- Enable the MTD Physmap flash driver, so that the changes done
earlier by Marc Zyngier replacing integrator-flash takes
effect
- Enable the PL030 RTC driver that has not been default-compiled
with any config for a while
This has been tested on the real hardware Integrator AP with
both an ARM920T and ARM926EJ-S core module.
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We already have a clock definition for the 24MHz clock in
the Integrator, use that instead of some unclear defines
from the platform.h header. Also delete the senseless
comment that the file shouldn't be edited, I just edited it
and the world didn't come to an end, so it's obviously
false. If anyone still has the mentioned ".s file" and the
s2h awk script generating that header, raise your hand
(and give me your files).
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Drop mult, shift and delta calculations and let the
clockevent core scale this as appropriate.
Set the minimum interval to 1 rather than 15 (0xf), there
is nothing in the data sheets I have indicating that 15
should be some minimum value.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Integrator AP timer has no problem supporting oneshot
ticks with proper code, so let's do it so we can have
NOHZ configured in for this platform too.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
These macros are not used by anything since the switch to
generic time in commit b9cedda230793cbf58eb012ddadedd490cc8e129
so let's retire them.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
As per request of rmk, the options should be sorted alphabetically.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the legacy ARM LED code for simpad devices and
register a stadard LED platform device using GPIO line
instead.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
