summaryrefslogtreecommitdiff
path: root/arch/sh
AgeCommit message (Collapse)AuthorFilesLines
2007-09-21sh: se7206: update defconfig.Paul Mundt1-131/+92
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: se7206: Handle non-SuperIO I/O ports.Paul Mundt1-0/+2
This fixes up the port calculation logic for non-SuperIO accesses, before these were always matching the MRSHPC base, now just make sure the original port is handed back if it's not in the I/O port range. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: r7780rp: irq-r7780rp needs linux/io.h.Paul Mundt1-0/+1
Trivial build fix. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: hp6xx: Trivial build fixes for INTC changes.Paul Mundt1-1/+1
Get the IRL->IRQ stuff building. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: se7206: heartbeat needs 32-bit writes.Paul Mundt1-0/+1
Most boards use 8 or 16-bit access for the LED bank, se7206 needs 32. There's only 8 individual LEDs however, each with a 'special' value in terms of logical ordering. Go FPGA, go! Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: se7206: Make the I/O port routines less stupid.Paul Mundt2-33/+4
The port routines were logically inverted, and the MRSHPC range had no upper bound, causing 8 and 16-bit port I/O to get mangled. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Magic Panel R2 board support.Markus Brunner6-0/+1261
This adds support for the SH7720 (SH3-DSP) based Magic Panel R2 board. Signed-off-by: Markus Brunner <super.firetwister@gmail.com> Signed-off by: Mark Jonas <toertel@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: hp6xx: Enable pata_platform in defconfig.Kristoffer Ericson1-18/+4
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: hp6xx: Enable touchscreen and powerbutton IRQs.Kristoffer Ericson1-9/+24
IRQ0->IRQ3 need to be an IRQ mode for these to work, fix them up. Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Don't enable FPU for SH4AL-DSP.Paul Mundt2-1/+5
This leads to invalid configurations where both FPU and DSP support can be enabled in the same kernel, resulting in build failure. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: INTC stubs for SH7343 and SH7770 builds.Paul Mundt2-0/+8
Get the SH7343 and SH7770 stuff linking again. Both of these still require proper INTC support. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: hp6xx: Update CF IRQ for INTC changes.Kristoffer Ericson1-1/+1
The vector changed, so follow the INTC changes for the new vector. Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: dma: Fix up build for SH7709 support.Kristoffer Ericson1-0/+1
Trivial build fixes for SH7709. Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: hd64461: Trivial build fixes for SH7709.Kristoffer Ericson1-1/+5
Some trivial fixes to get SH7709 + HD64461 building again. Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: hp6xx: APM build fix and new battery values.Kristoffer Ericson1-5/+4
Build fixes for the hp6xx APM code, as well as some adjustments for the battery values. Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: update hp6xx defconfig.Kristoffer Ericson1-293/+268
hp6xx_defconfig resync. Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: nommu fault handler needs signal.h.Paul Mundt1-0/+1
Trivial build fix. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Fix up se7751 build.Paul Mundt1-1/+0
Trivial compile fix. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: remove sh7780 interrupt controller hack from pci codeMagnus Damm1-13/+0
This patch removes the sh778x specific pci code that pokes in the interrupt controller and overwrites things. The new and improved IRL code manages this in plat_irq_setup() and plat_irq_setup_pins() instead. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - rework higlander irq code for r7780mp and r7785rpMagnus Damm5-19/+152
This patch reworks the highlander irq code for r7780mp and r7785rp. The same strategy as for the new R2D code is used here - the board specific interrupts are now starting from HL_FPGA_IRQ_BASE. The code for r7780rp is not touched due to lack of hardware. Tested with CF, AX88796 on r7780mp and r7785rp. The touch switch interrupt has also been tested on r7780mp. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: minor fixesMagnus Damm3-2/+1
This patch contains the following fixes: - Adds sh7785 support to CONFIG_EARLY_SCIF_CONSOLE_PORT. - Removes duplicate include from rts7751r2d irq code. - Removes CONFIG_CPU_HAS_INTC from sh7720 Kconfig entry. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - irl mode update for sh7780 and sh7785Magnus Damm2-4/+84
This patch contains the following fixes and improvements: - Fix address typo for INTMSK2 / INTMSKCLR2 registers on sh7780. - Adds IRQ_MODE_IRLnnnn_MASK using intc controller for IRL masking. - Good old IRQ_MODE_IRLnnnn should not register any intc controller. - plat_irq_setup_pins() now selects IRL or IRQ mode. - the holding function is now disabled using ICR0. By default all external pin interrupts are disabled. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: remove CONFIG_CPU_HAS_INTC_IRQMagnus Damm3-25/+1
All processor specific interrupt code is now converted to make use of the new intc code. The config option CONFIG_CPU_HAS_INTC_IRQ is because of that pointless. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Fix up heartbeat build and resource size.Paul Mundt11-15/+15
We were abusing the resource size for the number of bits, this has been reworked using proper platform data, so this can be tidied up now. Boards in general only have a 1-byte wide resource, which the ioremap_nocache() case already handles. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: defconfigs for R2D-PLUS and for R2D-1Magnus Damm2-329/+1310
This patch removes the old r2d config file named rts7751r2d_defconfig and adds separate config files for the two r2d board versions. The two new defconfigs are identical with the exception of board selection: - rts7751r2dplus_defconfig selects CONFIG_RTS7751R2D_PLUS=y - rts7751r2d1_defconfig selects CONFIG_RTS7751R2D_1=y Please remember to update both files with r2d changes in the future. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Kill off volatile silliness in sq_flush_range().Paul Mundt1-2/+2
CC arch/sh/kernel/cpu/sh4/sq.o arch/sh/kernel/cpu/sh4/sq.c: In function 'sq_flush_range': arch/sh/kernel/cpu/sh4/sq.c:65: warning: passing argument 1 of 'prefetch' discards qualifiers from pointer target type This didn't actually need to be volatile in the first place, so just kill off the qualifier entirely. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: More license string silliness.Paul Mundt2-2/+2
'GPL v2' vs 'GPLv2'. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: heartbeat driver update.Paul Mundt7-39/+87
Add some flags for the heartbeat driver, and kill off some duplication in the bit positions for the boards that don't have special cases. This also allows for variable access widths and inversion. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - add support for sh7206Magnus Damm2-52/+159
This patch converts the cpu specific interrupt setup code for sh7206 from ipr to intc. New vectors are also added to match the information provided by the datasheet. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - add support for sh7619Magnus Damm2-38/+57
This patch converts the cpu specific interrupt setup code for sh7619 from ipr to intc. New vectors are also added to match the information provided by the datasheet. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: fix irqs for the second serial port on sh7206Magnus Damm1-4/+4
This patch makes sure the serial port interrupt irqs matches the datasheet. Only irqs for SCIF1 are changed. While at some cosmetic spaces are added. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - primary priority masking fixesMagnus Damm1-5/+28
This patch contains various intc fixes for problems reported by Markus Brunner on the linuxsh-dev mailing list: http://marc.info/?l=linuxsh-dev&m=118701948224991&w=1 Apart from added comments, the fixes are: - add intc_set_priority() function prototype to hw_irq.h - fix off-by-one error in intc_set_priority() - make sure _INTC_WIDTH() is set for primary priority masking Big thanks to Markus for finding these problems. Version two fixes a compile error and an inverted primary check. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Markus Brunner <super.firetwister@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - mark data structures as __initdataMagnus Damm11-79/+76
With the intc core improved it is now possible to put the intc data structures in the initdata section. Version two of this patch puts the __initdata inside DECLARE_INTC_DESC() and removes the __initdata included in the board specific r2d code. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: x3 - add ipi vectorsMagnus Damm1-0/+9
With the intc dual prio register support in place it is now possible to add the ipi vectors to x3. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: replace sh specific CONFIG_VOYAGERGX with CONFIG_MFD_SM501Magnus Damm4-31/+25
This patch replaces all instances of CONFIG_VOYAGERGX with CONFIG_MFD_SM501. While at it we make sure the r2d code compiles both with and without SM501. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - convert board specific r2d codeMagnus Damm4-62/+151
This patch converts the board specific interrupt code for r2d to make use of intc. While at it we improve the Kconfig to avoid confusion. - Two sets of interrupt tables exist - one for R2D-1 and one for R2D-PLUS. - R2D-1 and R2D-PLUS use the same irq constants. - R2D-1 has AX88796 support, R2D-PLUS does not hook up that IRQ. - R2D-PLUS has KEY support, R2D-1 does not hook up that IRQ. - The number and order of IRQ values are disconnected from register bits. - Interrupt sources now start from IRQ 100. - The machvec demux function converts from irlm IRQ 0-14 to IRQ 100++. Tested on R2D-1 and R2D-PLUS boards. Version 2 adds CONFIG_RTS7751R2D_1 and CONFIG_RTS7751R2D_PLUS together with intc structured as __initdata. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - rework core codeMagnus Damm2-212/+328
This patch reworks the intc core, implementing the following features: - Support dual priority registers - one set and one clear register - All 8/16/32 bit register combinations are now supported - Both single mask and single enable bitmap register are supported - Add code to set interrupt priority - Speedup sense and priority configuration code - Allocate data using bootmem, allows intc data structures to be __initdata - Save memory - allocated memory footprint is smaller than intc structures Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc - add a clear register to struct intc_prio_regMagnus Damm10-96/+104
We need a secondary register member in struct intc_prio_reg to support dual priority registers used by ipi on x3. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: x3 - fix setup_bootmem_node() compile error with shx3_defconfigMagnus Damm1-0/+1
This makes sure the function prototype for setup_bootmem_node() gets included. The file setup-shx3.c does not compile otherwise for CONFIG_NUMA=n. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Add SH7720 CPU support.Markus Brunner10-9/+271
This adds support for the SH7720 (SH3-DSP) CPU. Signed-off by: Markus Brunner <super.firetwister@gmail.com> Signed-off by: Mark Jonas <toertel@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Kill off duplicate symbol exports on SMP.Paul Mundt1-6/+1
synchronize_irq() was being exported twice, kill off the duplicate export. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Wire up CSM node for SH-X3.Paul Mundt1-5/+8
Now that NODES_SHIFT is bumped up, we can plug in the CSM block as a separate node, too. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Bump up NODES_SHIFT for SH-X3.Paul Mundt1-0/+1
This was at 1, which is where most subtypes want it. SH-X3 has more nodes, so bump it up to 3. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: x3proto: Trivial ILSEL build fix.Paul Mundt1-3/+3
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: x3proto: Hook up ethernet and USB platform devices.Paul Mundt1-0/+82
Now that we have a way of enabling the IRQs, hook up the platform devices and wrap in to ILSEL for mapping the vectors. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: x3proto: ILSEL IRQ support.Paul Mundt2-1/+152
This adds functionality for the on-board ILSEL IRQs that chain IRL mode events. Many on-board devices (ethernet, usb, etc.) rely on ILSEL IRQs directly. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Initial support for SH-X3 prototype board.Paul Mundt4-0/+60
This adds initial support for the SH-X3 prototype board. Only simple logic for the IRQ controller and the heartbeat driver for now. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: Plug in SH-X3 SCIF0 for sercon earlyprintk.Paul Mundt1-1/+3
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: intc: Fix sense regs oops for IRL IRQs.Paul Mundt1-1/+1
IRL doesn't always define sense registers, so don't bother trying to iterate through the table. This ended up causing an oops on SH-X3 when using IRL mode. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21sh: remove intc2 codeMagnus Damm4-91/+0
There is no point in keeping around the now unused intc2 code. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 18:49:25 +0000