Age | Commit message (Collapse) | Author | Files | Lines |
|
|
|
If the SG bit is set in MMUTR the page is accessible for all
userspace processes (ignoring the ASID). So a process might randomly
access a page from a different process which had a shared page
(from shared memory) in its context.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
We had problems accessing our NOR flash trough mtd. The system always got
stuck at attaching UBI using ubiattach if booted from NFS or after mounting
squashfs as rootfs directly from NOR flash.
After some testing of the new changes introduced from v3.2-rc1 to v3.2-rc7
we had to apply the following patch to get mtd working again.
[gerg: The problem was ultimately caused by allocated kernel pages not having
the shared (SG) bit set. Without the SG bit set the MMU will look for page
matches incorporating the ASID as well. Things like module regions allocated
using vmalloc would fault when other processes run. ]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The return path from an exception was checking too many bits in the
thread_info->flags, and getting stuck calling do_signal(). There was
no work to do, we should only be checking the low 8 bits (as per comments
and definitions in arch/m68k/include/asm/thread_info.h).
This fixes the stuck process problem when using strace.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
|
|
Convert the driver to standard spilt model arch-specific code registers
platform device to which driver code can bind later.
Also request IRQ immediately upon binding to the device instead of doing
this when serio port is being opened.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Passing the address of a variable as an operand to an asm statement
doesn't mark the value of this variable as used, so gcc may optimize its
initialisation away. Fix this by using the "m" constraint instead.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
|
|
The m68k core irq code stopped honoring these flags during the irq
restructuring in 2006.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Use the more commonly used __noreturn instead of ATTRIB_NORETURN.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's a very old and now unused prototype marking so just delete it.
Neaten panic pointer argument style to keep checkpatch quiet.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
frv, h8300, m68k, microblaze, openrisc, score, um and xtensa currently
do not register a CPU device. Add the config option GENERIC_CPU_DEVICES
which causes a generic CPU device to be registered for each present CPU,
and make all these architectures select it.
Richard Weinberger <richard@nod.at> covered UML and suggested using
per_cpu.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (21 commits)
m68k/mac: Make CONFIG_HEARTBEAT unavailable on Mac
m68k/serial: Remove references to obsolete serial config options
m68k/net: Remove obsolete IRQ_FLG_* users
m68k: Don't comment out syscalls used by glibc
m68k/atari: Move declaration of atari_SCC_reset_done to header file
m68k/serial: Remove references to obsolete CONFIG_SERIAL167
m68k/hp300: Export hp300_ledstate
m68k: Initconst section fixes
m68k/mac: cleanup macro case
mac_scsi: fix mac_scsi on some powerbooks
m68k/mac: fix powerbook 150 adb_type
m68k/mac: fix baboon irq disable and shutdown
m68k/mac: oss irq fixes
m68k/mac: fix nubus slot irq disable and shutdown
m68k/mac: enable via_alt_mapping on performa 580
m68k/mac: cleanup forward declarations
m68k/mac: cleanup mac_irq_pending
m68k/mac: cleanup mac_clear_irq
m68k/mac: early console
m68k/mvme16x: Add support for EARLY_PRINTK
...
Fix up trivial conflict in arch/m68k/Kconfig.debug due to new
EARLY_PRINTK config option addition clashing with movement of the
BOOTPARAM options.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (56 commits)
m68k: allow ColdFire 547x and 548x CPUs to be built with MMU enabled
m68k/Kconfig: Separate classic m68k and coldfire early
m68k: add ColdFire with MMU enabled support to the m68k mem init code
m68k: do not use m68k startup or interrupt code for ColdFire CPUs
m68k: add ColdFire FPU support for the V4e ColdFire CPUs
m68k: adjustments to stack frame for ColdFire with MMU enabled
m68k: use non-MMU linker script for ColdFire MMU builds
m68k: ColdFire with MMU enabled uses same clocking code as non-MMU
m68k: add code to setup a ColdFire 54xx platform when MMU enabled
m68k: use non-MMU entry.S code when compiling for ColdFire CPU
m68k: create ColdFire MMU pgalloc code
m68k: compile appropriate mm arch files for ColdFire MMU support
m68k: ColdFire V4e MMU paging init code and miss handler
m68k: use ColdFire MMU read/write bit flags when ioremapping
m68k: modify cache push and clear code for ColdFire with MMU enable
m68k: use tracehook_report_syscall_entry/exit for ColdFire MMU ptrace path
m68k: ColdFire V4e MMU context support code
m68k: MMU enabled ColdFire needs 8k ELF alignment
m68k: set ColdFire MMU page size
m68k: define PAGE_OFFSET_RAW for ColdFire CPU with MMU enabled
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1958 commits)
net: pack skb_shared_info more efficiently
net_sched: red: split red_parms into parms and vars
net_sched: sfq: extend limits
cnic: Improve error recovery on bnx2x devices
cnic: Re-init dev->stats_addr after chip reset
net_sched: Bug in netem reordering
bna: fix sparse warnings/errors
bna: make ethtool_ops and strings const
xgmac: cleanups
net: make ethtool_ops const
vmxnet3" make ethtool ops const
xen-netback: make ops structs const
virtio_net: Pass gfp flags when allocating rx buffers.
ixgbe: FCoE: Add support for ndo_get_fcoe_hbainfo() call
netdev: FCoE: Add new ndo_get_fcoe_hbainfo() call
igb: reset PHY after recovering from PHY power down
igb: add basic runtime PM support
igb: Add support for byte queue limits.
e1000: cleanup CE4100 MDIO registers access
e1000: unmap ce4100_gbe_mdio_base_virt in e1000_remove
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, tsc: Skip TSC synchronization checks for tsc=reliable
clocksource: Convert tcb_clksrc to use clocksource_register_hz/khz
clocksource: cris: Convert to clocksource_register_khz
clocksource: xtensa: Convert to clocksource_register_hz/khz
clocksource: um: Convert to clocksource_register_hz/khz
clocksource: parisc: Convert to clocksource_register_hz/khz
clocksource: m86k: Convert to clocksource_register_hz/khz
time: x86: Replace LATCH with PIT_LATCH in i8253 clocksource driver
time: x86: Remove CLOCK_TICK_RATE from acpi_pm clocksource driver
time: x86: Remove CLOCK_TICK_RATE from mach_timer.h
time: x86: Remove CLOCK_TICK_RATE from tsc code
time: Fix spelling mistakes in new comments
time: fix bogus comment in timekeeping_get_ns_raw
|
|
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
mac_heartbeat() was never really implemented.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
... some still remain weird :-/
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The ColdFire 547x and 548x CPUs have internal MMU hardware. All code
to support this is now in, so we can build kernels with it enabled.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
While you can build multiplatform kernels for machines with classic
m68k processors, you cannot mix support for classic m68k and coldfire
processors. To avoid such hybrid kernels, introduce CONFIG_M68KCLASSIC
as an antipole for CONFIG_COLDFIRE, and make all specific processor
support depend on one of them.
All classic m68k machine support also needs to depend on this.
The defaults (CONFIG_M68KCLASSIC if MMU, CONFIG_COLDFIRE if !MMU) are
chosen such to make most of the existing configs build and work.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire has similar setup requirements to the SUN3 code, so we
use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The ColdFire CPUs have their own startup and interrupt code (in the
platform/coldfire directory), and do not use the general m68k startup and
interrupt code. In fact the use of the arch/m68k/kernel/head.o is not about
CONFIG_MMU or not, it is really about the machine type we are compiling for.
Modify the selection and use of head.o to be based on the machine type.
Only select the local ints.o and vectors.o code if we are using the classic
68k CPU types (that use the conventional Morotola MMU or SUN3 MMU).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The V4e ColdFire CPU family also has an integrated FPU (as well as the MMU).
So add code to support this hardware along side the existing m68k FPU code.
The ColdFire FPU is of course different to all previous 68k FP units. It is
close in operation to the 68060, but not completely compatible. The biggest
issue to deal with is that the ColdFire FPU multi-move instructions are
different. It does not support multi-moving the FP control registers, and
the multi-move of the FP data registers uses a different instruction
mnemonic.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The exception return stack adjustment required by ColdFire when running
with the MMU enabled is not completely identical to 680x0 processors.
Specifically the format type 4 stack frame doesn't need any stack
adjustment on exception return. And the ColdFire always must return with
a frame type of 4, not 0.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Use the non-MMU linker script for ColdFire builds when we are building
for MMU enabled. The image layout is correct for loading on existing
ColdFire dev boards. The only addition required to the current non-MMU
linker script is to add support for the fixup section.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
We want to use the same timer support code for ColdFire CPU's when
running with MMU enabled or not. So use the same time_no.c code even
when the MMU is enabled for ColdFire. This also means we do not want
CONFIG_ARCH_USES_GETTIMEOFFSET set, since that code is only in time_mm.c.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
We use the same setup code for ColdFire MMU enabled platforms as
standard m68k. So add support for it to setup our 54xx ColdFire
platforms. They do not support the same bootinfo parsing as other
m68k platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
No matter whether we are configured for non-MMU or MMU enabled if we are
compiling for ColdFire CPU we always use the entry_no.S code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Add code to support the ColdFire V4e MMU pgalloc functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Create a config symbol to enable when using a ColdFire MMU. We then
use that to only compile the necessary arch mm files.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The different ColdFire V4e MMU requires its own dedicated paging init
code, and a TLB miss handler for its software driven TLB.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The ColdFire MMU has separate read and write bits, unlike the Motorola
m68k MMU which has a single read-only bit.
Define a _PAGE_READWRITE value for the Motorola MMU, which is 0, so we
can unconditionaly include that in the page table entry bits when setting
up ioremapped pages.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The cache push and clear code only need to flush the branch cache on
the write-through cache setup of the ColdFire V4e with MMU enabled.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The existing ColdFire code (which is all non-mmu) for system call entry
and exit uses the more modern tracehook_report_syscall_entry()/exit()
into the ptrace code. Now that we are supporting ColdFire with MMU we
need the same hooks for these.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Add code to manage the context's of the ColdFire V4e MMU. This code is
mostly taken from the Freescale 2.6.35 kernel BSP for MMU enabled ColdFire.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Like the SUN3 hardware MMU the ColdFire MMU uses 8k pages. So we want
our ELF page size alingment to also be 8k. Modify the ELF alignment
setting.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
We use the ColdFire V4e MMU page size of 8KiB. Define PAGE_SHIFT
appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The ColdFire CPU configurations need PAGE_OFFSET_RAW set to the base of
their RAM. It doesn't matter if they are running with the MMU enabled or
disabled, it is always set to the base of RAM.
We can keep the choices simple here and key of CONFIG_RAMBASE. If it is
defined we are on a plaftorm (ColdFire or other non-MMU systems) which
have a configurable RAM base, just use it.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The ColdFire V4e MMU is unlike any of the other m68k MMU hardware.
It needs its own TLB flush support code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Modify the cache setup for the ColdFire 54xx parts when running with
the MMU enabled.
We want to map the peripheral register space (MBAR region) as non
cacheable. And create an identity mapping for all of RAM for the
kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Add code to deal with instruction, data and branch caches of the V4e
ColdFire cores when they are running with the MMU enabled.
This code is loosely based on Freescales changes for the caches of the
V4e ColdFire in the 2.6.25 kernel BSP. That code was originally by
Kurt Mahan <kmahan@freescale.com> (now <kmahan@xmission.com>).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Add code to traps.c to handle MMU exceptions for the ColdFire.
Most of this code is from the 2.6.25 kernel BSP code released by
Freescale.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Define the page table size and attributes for the ColdFire V4e MMU.
Also setup the vmalloc and kmap regions we will use.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
The ColdFire V4e MMU is nothing like any of the other m68k MMU's.
So we need to create a set of definitions and support routines
for the kernels paging functions.
This is largely taken from Freescales BSP code for this (though it
was a 2.6.25 kernel). I have cleaned it up alot from the original.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
|
|
Virtual memory m68k systems build with register a2 dedicated to being the
current proc pointer (non-MMU don't do this). Add code to the ColdFire
interrupt and exception processing to set this on entry, and at context
switch time. We use the same GET_CURRENT() macro that MMU enabled code
uses - modifying it so that the assembler is ColdFire clean.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|