| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM fixes from Russell King:
"Not much here, just a couple minor/cosmetic fixes and a patch for the
decompressor which fixes problems with modern GCC and CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7583/1: decompressor: Enable unaligned memory access for v6 and above
ARM: 7572/1: proc-v6.S: fix comment
ARM: 7570/1: quiet down the non make -s output
|
|
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.pengutronix.de/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull one more ARM SoC fix from Olof Johansson:
"I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
|
|
Modern GCC can generate code which makes use of the CPU's native
unaligned memory access capabilities. This is useful for the C
decompressor implementations used for unpacking compressed kernels.
This patch disables alignment faults and enables the v6 unaligned
access model on CPUs which support these features (i.e., v6 and
later), allowing full unaligned access support for C code in the
decompressor.
The decompressor C code must not be built to assume that unaligned
access works if support for v5 or older platforms is included in
the kernel.
For correct code generation, C decompressor code must always use
the get_unaligned and put_unaligned accessors when dealing with
unaligned pointers, regardless of this patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.
* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.
* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
|
|
Commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code) have enabled the
pendown GPIO debounce time setting by the below sequence:
gpio_request_one()
gpio_set_debounce()
gpio_free()
It also revealed a bug in the OMAP GPIO handling code which prevented
the GPIO debounce clock to be disabled and CORE transition to low power
states.
Commit c9c55d9 (gpio/omap: fix off-mode bug: clear debounce settings on
free/reset) fixes the OMAP GPIO handling code by making sure that the
GPIO debounce clock gets disabled if no GPIO is requested from current
bank.
While fixing the OMAP GPIO handling code (in the right way), the above
commit makes the gpio_request->set_debounce->free sequence invalid as
after freeing the GPIO, the debounce settings are lost.
Fix the debounce settings by moving the debounce initialization to the
actual GPIO requesting code - the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 8214513 ("ARM: EXYNOS: fix address for EXYNOS4 MDMA1")
changed EXYNOS specific setup of PL330 DMA engine to use 'non-secure'
mdma1 address instead of 'secure' one (from 0x12840000 to 0x12850000)
to fix issue with some Exynos4212 SOCs. Unfortunately it brakes
PL330 setup for revision 0 of Exynos4210 SOC (mdma1 device cannot
be found at 'non-secure' address):
[ 0.566245] dma-pl330 dma-pl330.2: PERIPH_ID 0x0, PCELL_ID 0x0 !
[ 0.566278] dma-pl330: probe of dma-pl330.2 failed with error -22
Fix it by using 'secure' mdma1 address on Exynos4210 revision 0 SOC.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Fix the video clock setting when custom timings are used with
pclock <= 27MHz. Existing video clock selection uses PLL2 mode
which results in a 54MHz clock whereas using the MXI mode results
in a 27MHz clock (which is the one actually desired).
This bug affects the Enhanced Definition (ED) support on DM644x.
Without this patch, out-range signals errors are were observed on
the TV when viewing ED. An out-of-range signal is often caused when
the field rate is above the rate that the television will handle.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
[nsekhar@ti.com: reword commit message based on on-list discussion]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Minor line offset auto-merges.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two little fixes, one related to the move to sparse irq and
another one fixing the check of a GPIO for USB host overcurrent.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/usbh: fix overcurrent gpio setup
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
fixes
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX fixes for 3.7-rc
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch sets HPM (Host power mask bit) to bit 16 according to i.MX
Reference Manual. Falsely it was set to bit 8, but this controls pull-up
Impedance.
Reported-by: Michael Burkey <mdburkey@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The error-valued pointer clk is used for the arg of kfree, it should be
kfree(gate) if clk_register() return ERR_PTR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Use gpio_is_valid also for overcurrent pins (which are currently
negative in many board files).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
support
Spare irq support introduced by commit 8fe82a5 (ARM: at91: sparse irq support)
involves to add the NR_IRQS_LEGACY offset to irq number.
Signed-off-by: Nicolas Royer <nicolas@eukrea.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Cc: stable@vger.kernel.org # 3.6
|
|
Add CPSW and MDIO related device tree data for AM33XX.
Also enable them into board/evm dts files by providing
respective phy-id.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable CPSW support in defconfig which is present in AM33xx SoC
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds hwmod entry for davinci MDIO module,
creating parent<->child relationship between CPSW and MDIO module.
This Parent-child relation is required in order to use common resources
like, clock, but still maintaining the logical separation between them.
CPGMAC SubSystem consist of various sub-modules, like, mdio, cpdma,
cpsw, etc... These sub-modules are also used in some of Davinci
family of devices, so separate and independent platform devices &
drivers for CPSW and MDIO is implemented.
In case of AM33XX, the resources are shared and common register
bit-field is provided to control module/clock enable/disable,
makes it difficult to handle common resources from both drivers.
So the solution is, create parent<->child relationship between
CPGMAC & MDIO modules.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3db11feffc1ad2ab9dea27789e6b5b3032827adc
(ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints).
This commit causes I2C timeouts to appear on several OMAP3430/3530-based
boards:
http://marc.info/?l=linux-arm-kernel&m=135071372426971&w=2
http://marc.info/?l=linux-arm-kernel&m=135067558415214&w=2
http://marc.info/?l=linux-arm-kernel&m=135216013608196&w=2
and appears to have been sent for merging before one of its prerequisites
was merged:
http://marc.info/?l=linux-arm-kernel&m=135219411617621&w=2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
This patch is a follow-up for patch "net: filter: add vlan tag access"
to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a follow-up for patch "filter: add XOR instruction for use
with X/K" that implements BPF ARM JIT parts for the BPF XOR operation.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit edc88ceb0 (ARM: be really quiet when building with 'make -s') the
following output is generated when building a kernel for ARM:
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
Building modules, stage 2.
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
As per Documentation/kbuild/makefiles.txt the correct way of using kecho is
'@$(kecho)'.
Make this change so no more unwanted 'echo' messages are displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
On OMAP4 boards using the TWL6030 PMIC, the sys_drm_msecure is
connected to the MSECURE input of the TWL6030 PMIC. This signal
controls the secure-mode operation of the PMIC. If its not mux'd
correctly, some functionality of the PMIC will not be accessible since
the PMIC will be in secure mode.
For example, if the TWL RTC is in secure mode, most of its registers
are read-only, meaning (re)programming the RTC (e.g. for wakeup from
suspend) will fail.
To fix, ensure the signal is properly mux'd as output when TWL is
intialized.
This fix is required when using recent versions of u-boot (>= v2012.04.01)
since u-boot is no longer setting the default mux for this pin.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Minor OMAP PM and hwmod fixes for v3.7-rc series via
Kevin Hilman and Paul Walmsley.
* tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: OMAP2+: PM: add missing newline to VC warning message
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
This series fixes an annoying regression to make MUSB working
on omap4 again. Although it's getting rather late for these
changes for the -rc cycle, it is important as many devices
are using MUSB for charging and connectivity.
With the USB PHY changes, MUSB started using the newly added
drivers/usb/phy/omap-usb2.c driver introduced by commit
657b306a (usb: phy: add a new driver for omap usb2 phy)
that is using the newly introduced drivers/bus/omap-ocp2scp.c
introduced by commit 26a84b3e (drivers: bus: add a new driver
for omap-ocp2scp).
These changes allowed dropping a lot of PHY related code from
arch/arm/mach-omap2/omap_phy_internal.c and have it live in
the device driver like it should with commit c9e4412a (arm: omap:
phy: remove unused functions from omap-phy-internal.c).
However, MUSB on omap4 broke with these changes for legacy
platform data boot, and now only works with device tree for
omap4. Unfortunately we are still few critical bindings away
from being able to make omap4 usbale with device tree.
Fix the regression properly by adding platform data support
to the ocp2scp driver so we can avoid adding back the driver
code to arch/arm/mach-omap2.
* tag 'omap-for-v3.7-rc4/musb-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit edc88ceb0c7d285b9f58bc29a638cd8163b59989 silenced the make -s build, but
inadvertently made louder the non-silent build. Fix by prepending '@' to each
of the added $(kecho) statements.
Build with edc88ceb0c7d285b9f58bc29a638cd8163b59989:
CHK include/generated/compile.h
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
Build with this fix:
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"There are three ARM compile fixes (we forgot to export certain
functions and if the drivers are built as an module - we go belly-up).
There is also an mismatch of irq_enter() / exit_idle() calls sequence
which were fixed some time ago in other piece of codes, but failed to
appear in the Xen code.
Lastly a fix for to help in the field with troubleshooting in case we
cannot get the appropriate parameter and also fallback code when
working with very old hypervisors."
Bug-fixes:
- Fix compile issues on ARM.
- Fix hypercall fallback code for old hypervisors.
- Print out which HVM parameter failed if it fails.
- Fix idle notifier call after irq_enter.
* tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/arm: Fix compile errors when drivers are compiled as modules (export more).
xen/arm: Fix compile errors when drivers are compiled as modules.
xen/generic: Disable fallback build on ARM.
xen/events: fix RCU warning, or Call idle notifier after irq_enter()
xen/hvm: If we fail to fetch an HVM parameter print out which flag it is.
xen/hypercall: fix hypercall fallback code for very old hypervisors
|
|
The commit 911dec0db4de6ccc544178a8ddaf9cec0a11d533
"xen/arm: Fix compile errors when drivers are compiled as modules." exports
the neccessary functions. But to guard ourselves against out-of-tree modules
and future drivers hitting this, lets export all of the relevant
hypercalls.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Setup the WIFI/BT GPIO pin muxes to enable WIFI/BT functionality.
This is needed to fix regression caused by recent versions of
u-boot that only mux essential pins.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Cc: Jonas Zetterberg <jozz@jozz.se>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Matthias Brugger <mbrugger@iseebcn.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Platfrom device for ocp2scp is created using omap_device_build in
devices file. This is used for both omap4(musb) and omap5(dwc3).
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In order to reflect devices(usb_phy) attached to ocp2scp bus, ocp2scp
is assigned a device attribute to represent the attached devices.
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We end up with:
ERROR: "HYPERVISOR_event_channel_op" [drivers/xen/xen-gntdev.ko] undefined!
ERROR: "privcmd_call" [drivers/xen/xen-privcmd.ko] undefined!
ERROR: "HYPERVISOR_grant_table_op" [drivers/net/xen-netback/xen-netback.ko] undefined!
and this patch exports said function (which is implemented in hypercall.S).
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Pull arm fixes from Russell King:
"Not much here again.
The two most notable things here are the sched_clock() fix, which was
causing problems with the scheduling of threaded IRQs after a suspend
event, and the vfp fix, which afaik has only been seen on some older
OMAP boards. Nevertheless, both are fairly important fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7569/1: mm: uninitialized warning corrections
ARM: 7567/1: io: avoid GCC's offsettable addressing modes for halfword accesses
ARM: 7566/1: vfp: fix save and restore when running on pre-VFPv3 and CONFIG_VFPv3 set
ARM: 7565/1: sched: stop sched_clock() during suspend
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.7-rc4/fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.7-rc4/fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into fixes
From Stephen Warren:
* 'for-3.7/fixes-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: fix length of pad control and mux registers
|
|
In some cases, an interrupt can occur and prevent cause failure to enter
wfi. This causes reset to hang. Retrying the wfi should be enough to
prevent reset from hanging.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Haojian Zhuang:
* 'upload/fix' of git://github.com/hzhuang1/linux:
ARM: pxa/spitz_pm: Fix hang when resuming from STR
ARM: pxa: hx4700: Fix backlight PWM device number
|
|
commit 24d7b40a (ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for
MPU-SS) updated the regulator name used for the MPU regulator, but only
updated OMAP3, not OMAP4. Fix the OMAP4 name as well, otherwise CPUfreq
fails to find the MPU regulator.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The variables here are really not used uninitialized.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
|
|
Set GRP1 BIT21 ENET_CLK_SEL:
Enet tx reference clk from internal clock from anatop
(loopback through pad), this clock also sent out to external PHY
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ENET 1588 clock input pin
MX6Q_PAD_GPIO_16__ENET_ANATOP_ETHERNET_REF_OUT
and anatop PLL8 clock source for ENET
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resolve this kernel boot message:
omap_hwmod: mcpdm: cannot be enabled for reset (3)
The McPDM on OMAP4 can only receive its functional clock from an
off-chip source. This source is not guaranteed to be present on the
board, and when present, it is controlled by I2C. This would
introduce a board dependency to the early hwmod code which it was not
designed to handle. Also, neither the driver for this off-chip clock
provider nor the I2C code is available early in boot when the hwmod
code is attempting to enable and reset IP blocks. This effectively
makes it impossible to enable and reset this device during hwmod init.
At its core, this patch is a workaround for an OMAP hardware problem.
It should be possible to configure the OMAP to provide any IP block's
functional clock from an on-chip source. (This is true for almost
every IP block on the chip. As far as I know, McPDM is the only
exception.) If the kernel cannot reset and configure IP blocks, it
cannot guarantee a sane SoC state. Relying on an optional off-chip
clock also creates a board dependency which is beyond the scope of the
early hwmod code.
This patch works around the issue by marking the McPDM hwmod record
with the HWMOD_EXT_OPT_MAIN_CLK flag. This prevents the hwmod
code from touching the device early during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
|
