| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use chipid[27:20] bits to identify the EXYNOS family while setting
up the serial port during the uncompression setup. This uses four
additional bits of chipid to identify the EXYNOS family since this
is required for identifying EXYNOS5420 SoC.
Change-Id: Ic7cc14e68d16ae3da2a7d2177b40e40b0295d9a8
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds correspond irq number for EXYNOS3250's rtc alarm irq to
make the irq to work as a wakeup source.
Change-Id: I8970496a597729b8ad70d0e0bb893052e56e24c9
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
This patch add Exynos3250 busfreq driver to support DVFS(Dynamic Voltage
Frequency Scaling) about Exynos3250's Memory interface and bus. Exynos3250
busfreq driver will optimize power-consumption/performance of memory according
to PPMU(Profiling Performance Monitoring Unit) Read/Write count of Exynos3250
SoC.
- Exynos3250 MIF (DMC block) use following PPMU to check utilization
of MIF block.
: PPMU_DMC0
: PPMU_DMC1
- Exynos3250 INT (Internal block except for ARM/DMC/G3D) use following PPMU
to check utilization of INT block.
: PPMU_LEFT
: PPMU_RIGHT
Change-Id: If35c1fa0228f16547015931c64b0d6e896599d46
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
This patch add support for suspend-to-ram of Exynos3250 based on Cortex-A7
dual-core. The Exynos3250 hasn't L2 cache.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Exynos3250
This patch add PMU (Power Management Unit) configuration registers to support
suspend-to-RAM for Exynos3250. This patch for Exynos3250 provides four power
modes. (Normal/AFTR/W-AFTR/Sleep)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
This patch set AUTOWAKEUP_EN bit to ARM_CORE_CONFIGURATION register
because Exynos3250 removes WFE in secure mode so that turn on automatically
after setting CORE_LOCAL_PWR_EN. Also, This patch use dbs_sev() macro
to guarantee the data synchronization of command instead of IPI_WAKEUP
because Exynos3250 don't have WFE mode in secue mode.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
This patch map CPU IO area for Exynos3.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Change-Id: I086cf498da1f1fd38410e99cd250b0c4aeda1a09
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
is entered
This patch adds support for setting ARM cores' clock frequency down when
entering WFI/WFE based cpuidle state.
On the Trats2 device: performance governor, 1.4 GHz frequency, no extra
load, 4 cores enabled:
Without core clock down feature: 395 mA
With core clock down feature: 337 mA
Power consumption reduction around 15%
Change-Id: I7bae29b0332a97c7b18ffb79f4b0a5ff3d70b7ce
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch fixes DMC's physical SFR address base which is used for
static memory mapping as EXYNOS4210 and EXYNOS4x12 uses different SFR
addresses for them.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
|
|
Generic PHY drivers are used to handle the MIPI CSIS and MIPI DSIM
DPHYs so we can remove now unused code at arch/arm/plat-samsung.
In case there is any board file for S5PV210 platforms using MIPI
CSIS/DSIM (not any upstream currently) it should use the generic
PHY API to bind the PHYs to respective PHY consumer drivers and
a platform device for the PHY provider should be defined.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
S5P_ARM_CORE1_* registers affect only core 1. To control further cores
properly another registers must be used.
This patch replaces S5P_ARM_CORE1_* register definitions with
S5P_ARM_CORE_*(x) macro which return addresses of registers for specified
core.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
On DT-enabled systems pinctrl-exynos driver is responsible for handling
of wake-up EINT interrupts. This patch adjusts wake-up mask
configuration code to take wake-up mask value from pinctrl-exynos driver
on DT-enabled systems.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.
This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM platform specific firmware interfaces from Olof Johansson:
"Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here,
which would extend support for the existing generic "psci" call that
is used on multiple platforms as well as Xen and KVM guests, but that
ended up getting dropped because the patches were not ready in time."
* tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm: mark bcm_kona_smc_init as __init
ARM: bcm281xx: Add DT support for SMC handler
ARM: bcm281xx: Add L2 cache enable code
ARM: EXYNOS: Add secure firmware support to secondary CPU bring-up
ARM: EXYNOS: Add IO mapping for non-secure SYSRAM.
ARM: EXYNOS: Add support for Exynos secure firmware
ARM: EXYNOS: Add support for secure monitor calls
ARM: Add interface for registering and calling firmware-specific operations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform updates from Olof Johansson:
"More multiplatform enablement for ARM platforms. The ones converted
in this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was
a patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then"
* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
clocksource: nomadik-mtu: fix up clocksource/timer
Revert "ARM: exynos: enable multiplatform support"
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: exynos: enable multiplatform support
rtc: s3c: make header file local
mtd: onenand/samsung: make regs-onenand.h file local
thermal/exynos: remove unnecessary header inclusions
mmc: sdhci-s3c: remove platform dependencies
ARM: samsung: move mfc device definition to s5p-dev-mfc.c
ARM: exynos: move debug-macro.S to include/debug/
ARM: exynos: prepare for sparse IRQ
ARM: exynos: introduce EXYNOS_ATAGS symbol
ARM: tegra: build assembly files with -march=armv7-a
ARM: Push selects for TWD/SCU into machine entries
ARM: ux500: build hotplug.o for ARMv7-a
ARM: ux500: move to multiplatform
ARM: ux500: make remaining headers local
ARM: ux500: make irqs.h local to platform
ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
...
|
|
On device tree enabled exynos platforms, retrieve the physical base address
of the chip-id controller from device tree and create a virtual I/O mapping
for the chip-id controller. This helps to remove the chip-id controller entry
from the statically defined I/O mapping tables.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 6e6aac75 "ARM: EXYNOS: Migrate clock support to common
clock framework" from Thomas Abraham removed the Exynos5 specific
register definitions as they were unused at the time, but the
cpufreq driver actually still uses them.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merging this into the next/drivers branch avoids a number of
pointless conflicts with code changed here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The move is necessary to support early debug output on exynos
with multiplatform configurations. This implies also moving the
plat/debug-macro.S file, but we are leaving the remaining users of that
file in place, to avoid adding large numbers of extra configuration
options to Kconfig.debug
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When we enable CONFIG_SPARSE_IRQ, we have to set the value of NR_IRQS in
the machine_desc for legacy IRQ domains, and any file referring to the
number of interrupts or a specific number must include the mach/irqs.h
header file explicitly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
On TrustZone-enabled boards the non-secure SYSRAM is used for secondary
CPU bring-up, so add a mapping for it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch defines irq numbers of ARM performance monitoring unit for exynos4.
Firs of all, we need to fix IRQ_PMU correctly and to split pmu initialization
of exynos from plat-samsung for easily defining it.
The number of CPU cores and PMU irq numbers are vary according to soc types.
So, we need to identify each soc type using soc_is_xxx function and to define
the pmu irqs dynamically. For example, the exynos4412 has 4 cpu cores and pmus.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch corrects combined IRQs for exynos4 series platform. The exynos4412
has four extra combined irq group and the exynos4212 has two more combined
irqs
than exynos4210. Each irq is mapped to IRQ_SPI(xx). Unfortunately, extra 4
combined IRQs isn't sequential. So, we need to map the irqs manually.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: changes moved into drivers/irqchip/]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Setting this bit to 0 causes the system to wait until suspended
to use the wakeup masks. With it being set high previously,
masked interrupts were being received and processed before the
EINT_WAKEUP_MASK was configured.
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
For legacy reasons EINT_0 was being forced on for all
exynos systems as a wake interrupt. For boards that need
EINT_0 they should probably enable it with enable_irq_wake
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Remove Samsung specific clock support in Exynos4/5 and migrate to
use common clock framework.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
With device tree support enabled for MCT controller, the
staticio-remapping of the MCT controller address space is
removed for Exynos5 platforms (which supports only device
tree based boot).
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Allow the MCT controller base address and interrupts to be
obtained from device tree and remove unused static definitions
of these. The non-dt support for Exynos5250 is removed but
retained for Exynos4210 based platforms.
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
All the MCT register read/writes use a fixed remapped address
S5P_VA_SYSTIMER. With device tree support for MCT controller,
it is possible to remove the static remap of the MCT controller
address space and do the remap during the initialization of the
MCT controller with the physical address obtained from the device
tree.
So in preparation of adding device tree support for MCT controller,
add a new register base address variable that will hold the remapped
MCT controller base address and convert all MCT register read/writes
to use this new variable as the base address instead of the fixed
S5P_VA_SYSTIMER.
While at it, the MCT register offset and bit mask definitions are
moved into the MCT controller driver file since there are no other
consumers of these definitions.
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by
the respective maintainers."
* tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (23 commits)
iommu/tegra: assume CONFIG_OF in SMMU driver
iommu/tegra: assume CONFIG_OF in gart driver
iommu/amd: Remove redundant NULL check before dma_ops_domain_free().
iommu/amd: Initialize device table after dma_ops
iommu/vt-d: Zero out allocated memory in dmar_enable_qi
iommu/tegra: smmu: Fix incorrect mask for regbase
iommu/exynos: Make exynos_sysmmu_disable static
ARM: mach-shmobile: r8a7740: Add IPMMU device
ARM: mach-shmobile: sh73a0: Add IPMMU device
ARM: mach-shmobile: sh7372: Add IPMMU device
iommu/shmobile: Add iommu driver for Renesas IPMMU modules
iommu: Add DOMAIN_ATTR_WINDOWS domain attribute
iommu: Add domain window handling functions
iommu: Implement DOMAIN_ATTR_PAGING attribute
iommu: Check for valid pgsize_bitmap in iommu_map/unmap
iommu: Make sure DOMAIN_ATTR_MAX is really the maximum
iommu/tegra: smmu: Change SMMU's dependency on ARCH_TEGRA
iommu/tegra: smmu: Use helper function to check for valid register offset
iommu/tegra: smmu: Support variable MMIO ranges/blocks
iommu/tegra: Add missing spinlock initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
AS I commented, this makes <mach/*.h> local so that they could be removed.
* 'next/cleanup-header' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (26 commits)
ARM: S3C64XX: Fix missing header error with CONFIG_CPU_IDLE enabled
ARM: S3C64XX: make regs-syscon-power.h local
ARM: S3C64XX: make regs-sys.h local
ARM: S3C64XX: make regs-srom.h local
ARM: S3C64XX: make regs-modem.h local
ARM: S3C64XX: make regs-gpio-memport.h local
ARM: S3C64XX: make crag6410.h local
ARM: S3C24XX: remove dsc.c and make regs-dsc.h local
ARM: S3C24XX: remove idle.h
ARM: S3C2412: cleanup regs-s3c2412.h
ARM: S3C2416: remove regs-s3c2416-mem.h and regs-s3c2416.h
ARM: S3C24XX: make vr1000-cpld.h, vr1000-irq.h and vr1000-map.h local
ARM: S3C24XX: make otom-map.h local
ARM: S3C24XX: make osiris-cpld.h and osiris-map.h local
ARM: S3C24XX: make h1940.h and h1940-latch.h local
ARM: S3C24XX: make gta02.h local
ARM: S3C24XX: make bast-cpld.h, bast-irq.h and bast-map.h local
ARM: S3C24XX: make anubis-cpld, anubis-irq and anubis-map local
ARM: SAMSUNG: cleanup mach/gpio-fns.h gpio-track.h and gpio-nrs.h
ARM: SAMSUNG: cleanup mach/regs-audss.h file
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
|
|
This removes System MMU initialization from arch/arm/mach-exynos/
to move them to DT and the exynos-iommu driver except gating clock
definitions.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Pull ARM Soc updates, take 2, from Olof Johansson:
"This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that
we couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform."
Fix up conflicts mostly as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
sh: clkfwk: fixup unsed variable warning
Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
ARM: highbank: use common debug_ll_io_init
ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
ARM: shmobile: sh7372: remove fsidivx clock
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
|
|
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
|
|
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
* 'next/cleanup-samsung-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
|
|
Remove the unused regs-mem.h file
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
With device tree support enabled for dwmci controller, the unused
non-dt support for dwmci controller can be removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: updated as per Seungwon Jeon's pointing out]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds support for EXYNOS5440 SoC which is including
ARM Cortex-A15 Quad cores.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 8214513 ("ARM: EXYNOS: fix address for EXYNOS4 MDMA1")
changed EXYNOS specific setup of PL330 DMA engine to use 'non-secure'
mdma1 address instead of 'secure' one (from 0x12840000 to 0x12850000)
to fix issue with some Exynos4212 SOCs. Unfortunately it brakes
PL330 setup for revision 0 of Exynos4210 SOC (mdma1 device cannot
be found at 'non-secure' address):
[ 0.566245] dma-pl330 dma-pl330.2: PERIPH_ID 0x0, PCELL_ID 0x0 !
[ 0.566278] dma-pl330: probe of dma-pl330.2 failed with error -22
Fix it by using 'secure' mdma1 address on Exynos4210 revision 0 SOC.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In idle state down clocking the arm cores can result in power
savings. Program the power control registers to achieve this and
save these registers across a suspend/resume cycle.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
