summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2009-09-01ASoC: new board driver to connect bfin-5xx with ad1836 codecBarry Song3-0/+138
As discussed, the patch uses the original TDM order without rewriting. For the match between TDM slot number and audio channel number, a new API need be added. Signed-off-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-28ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAIJarkko Nikula2-0/+45
The McBSP1 port in OMAP3 processors (I believe OMAP2 too but I don't have specifications to check it) have additional CLKR and FSR pins for McBSP1 receiver. Reset default is that receiver is using bit clock and frame sync signal from those pins but it is possible to configure to use also CLKX and FSX pins as well. In fact, other McBSP ports are doing that internally that transmitter and receiver share the CLKX and FSX. Add functionaly that machine drivers can set the CLKR and FSR sources by using the snd_soc_dai_set_sysclk. Thanks to "Aggarwal, Anuj" <anuj.aggarwal@ti.com> for reporting the issue. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-28ASoC: davinci: i2c device creation moved into board filesChaithrika U S1-27/+5
Also, the codec setup data structure has to remain for successful probe. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-26ASoC: Don't reconfigure WM8350 FLL if not neededMark Brown1-0/+9
If the requested FLL configuration is the one we're currently running in it's at best pointless to reconfigure the FLL. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-26ASoC: Fix s3c-i2s-v2 buildMark Brown1-0/+1
We now need the PCM header to kick the DMA. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-26ASoC: Make platform data optional for TLV320AIC3xMark Brown1-7/+6
Now that we don't need the I2C address for the device the platform data is redundant so allow it to be omitted. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Tested-by: Chaithrika U S <chaithrika@ti.com>
2009-08-26ASoC: Add S3C24xx dependencies for Simtec machinesMark Brown1-2/+2
No point in building them for S3C64xx, certainly no sense in running into build issues there. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25ASoC: SDP3430: Fix TWL GPIO6 pin mux requestCandelaria Villareal, Jorge1-4/+11
Fix the write to PMBR1 register through I2C. Also, the constant which holds the value to write is now called TWL4030_GPIO6_PWM0_MUTE. This name is based on TRM to avoid confusion. Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25ASoC: S3C platform: Fix s3c2410_dma_started() called at improper timeShine Liu4-1/+25
s3c24xx dma has the auto reload feature, when the the trnasfer is done, CURR_TC(DSTAT[19:0], current value of transfer count) reaches 0, and DMA ACK becomes 1, and then, TC(DCON[19:0]) will be loaded into CURR_TC. So the transmission is repeated. IRQ is issued while auto reload occurs. We change the DISRC and DCON[19:0] in the ISR, but at this time, the auto reload has been performed already. The first block is being re-transmitted by the DMA. So we need rewrite the DISRC and DCON[19:0] for the next block immediatly after the this block has been started to be transported. The function s3c2410_dma_started() is for this perpose, which is called in the form of "s3c2410_dma_ctrl(prtd->params->channel, S3C2410_DMAOP_STARTED);" in s3c24xx_pcm_trigger(). But it is not correct. DMA transmission won't start until DMA REQ signal arrived, it is the time s3c24xx_snd_txctrl(1) or s3c24xx_snd_rxctrl(1) is called in s3c24xx_i2s_trigger(). In the current framework, s3c24xx_pcm_trigger() is always called before s3c24xx_pcm_trigger(). So the s3c2410_dma_started() should be called in s3c24xx_pcm_trigger() after s3c24xx_snd_txctrl(1) or s3c24xx_snd_rxctrl(1) is called in this function. However, s3c2410_dma_started() is dma related, to call this function we should provide the channel number, which is given by substream->runtime->private_data->params->channel. The private_data points to a struct s3c24xx_runtime_data object, which is define in s3c24xx_pcm.c, so s3c2410_dma_started() can't be called in s3c24xx_i2s.c Fix this by moving the call to signal the DMA started to the DAI drivers. Signed-off-by: Shine Liu <liuxian@redflag-linux.com> Signed-off-by: Shine Liu <shinel@foxmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stopJarkko Nikula3-63/+28
Functionality of functions omap_mcbsp_xmit_enable and omap_mcbsp_recv_enable can be merged into omap_mcbsp_start and omap_mcbsp_stop since API of those omap_mcbsp_start and omap_mcbsp_stop was changed recently allowing to start and stop individually the transmitter and receiver. This cleans up the code in arch/arm/plat-omap/mcbsp.c and in sound/soc/omap/omap-mcbsp.c which was the only user for those removed functions. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAIJarkko Nikula1-6/+2
Commit ca6e2ce08679c094878d7f39a0349a7db1d13675 is setting up few XCCR and RCCR bits for I2S and DPS_A formats. Part of the bits are already set for all formats and I believe that XDISABLE and RDISABLE bits are format independent. As XCCR and RCCR are found only from OMAP2430 and OMAP34xx, I move setup of XDISABLE and RDISABLE to where those cpu's are tested and remove format dependent part for simplicity. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25OMAP: McBSP: Use textual values in DMA operating mode sysfs filesJarkko Nikula1-23/+25
Use more descriptive than numerical value when showing and storing the McBSP DMA operating mode. Show function is using similar syntax than e.g. the led triggers so that all possible values for store function are printed but with current value surrounded with square brackets. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-24ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510Janusz Krzysztofik1-0/+10
Implement DMA channel self linking on OMAP1510 using AUTO_INIT and REPEAT flags of the DMA CCR register. Created against linux-2.6.31-rc5. Tested on Amstrad Delta. Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-24Merge branch 'topic/digital-mixing' into for-2.6.32Mark Brown3-21/+133
2009-08-24ASoC: Select core DMA when building for S3C64xxMark Brown1-0/+1
Ensure that the core DMA support is available when building for S3C64xx. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-24ASoC: Remove unneeded inclusion of linux/regulator/consumer.hTakashi Iwai1-1/+0
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-08-24ASoC: add missing inclusion of debugfs.hTakashi Iwai1-0/+1
To fix compile errors. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-08-23ASoC: Pass correct platform data from pxa2xx-ac97Marek Vasut2-4/+4
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-23ASoC: free socdev if init_card() fails in wm9705_soc_probe()Roel Kluin1-1/+1
Free socdev if snd_soc_init_card() fails. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: Add DAPM widget power decision debugfs filesMark Brown4-0/+96
Currently when built with DEBUG DAPM will dump information about the power state decisions it is taking for each widget to dmesg. This isn't an ideal way of getting the information - it requires a kernel build to turn it on and off and for large hub CODECs the volume of information is so large as to be illegible. When the output goes to the console it can also cause a noticable impact on performance simply to print it out. Improve the situation by adding a dapm directory to our debugfs tree containing a file per widget with the same information in it. This still requires a decision to build with debugfs support but is easier to navigate and much less intrusive. In addition to the previously displayed information active streams are also shown in these files. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: Add FSI-AK4642 sound support for SuperHKuninori Morimoto3-0/+117
This patch is tested by ms7724se Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: Add ak4642/ak4643 codec supportKuninori Morimoto4-0/+528
This is very simple driver for ALSA It supprt headphone output and stereo input only This patch is tested by ms7724se Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: S3C24XX: Support for Simtec Hermes boardsBen Dooks3-0/+163
Add support for the tlv320aic3x CODEC on the Simtec Hermes board. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: tlv320aic3x: fixup board device changesBen Dooks3-0/+30
Fixup the device changes by modifying the files that we just removed the explicit device creation from with i2c_register_board_info() until this can be moved into the relevant board files. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: tlv320aic3x: Change to use device modelBen Dooks5-113/+116
The tlv320aic3x driver managed its own i2c device, instead of an extant one created by the board support code. Change the code to make it so that the driver binds to an extant (in this case i2c) device. Add explict tlv320aic33 as well as tlv320aic3x to the supported device table and remove the old driver bindings from the users of this code. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-21ASoC: S3C24XX: Add audio core and tlv320aic23 for Simtec boardsBen Dooks6-0/+606
Add core support for the range of S3C24XX Simtec boards with TLV320AIC23 CODECs on them. Since there are also boards with similar IIS routing the AMP and the configuration code is placed in a core file for re-use with other CODEC bindings. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: OMAP: Use DMA operating mode of McBSPEduardo Valentin1-3/+15
Configures DMA sync mode depending on McBSP operating mode value. The value is configurable by McBSP instance. So, depending on McBSP operating mode, the DMA sync mode is passed from omap-mcbsp to omap-pcm. Besides that, it also configures McBSP threshold value depending on which McBSP mode is activated. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: OMAP: Use McBSP threshold to playback and captureEduardo Valentin3-7/+49
This patch changes the way DMA is done in omap-pcm.c in order to reduce power consumption. There is no need to have so much SW control in order to have DMA in idle state during audio streaming. Configuring McBSP threshold value and DMA to FRAME_SYNC are sufficient. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: Always syncronize audio transfers on framesEero Nurkkala1-0/+9
All these steps are required for ASoC to behave correctly. rccr and xccr are format dependent, for example TDM audio has different values than I2S or DSP_A. Also the omap_mcbsp_xmit_enable and/or omap_mcbsp_recv_enable must be called right after the DMA has started. This provides no longer L and R channels switching at random. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: Add runtime check for RFIG and XFIGEero Nurkkala1-2/+5
This is, no RFIG or XFIG (Not defined in 34xx), correct initiliazation of rccr and xccr. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: OMAP: Make DMA 64 alignedEduardo Valentin1-2/+2
Align DMA address to DMA burst transaction sizes. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: OMAP: Enable DMA burst modeEduardo Valentin1-0/+3
Improve DMA transfers by enabling Burst transaction. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Let element DMA mode hit retention alsoEero Nurkkala1-0/+9
The device no longer hits retention if element DMA mode is taken for at least the duration of the serial console timeout. Force element DMA mode to shut down through smartidle. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Do not enable wakeups for no-idle modeEero Nurkkala1-6/+7
When no-idle mode is taken, wakeups need not to be enabled. Moreover, CLOCKACTIVITY bits are unnecessary with this mode also. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Configure NO IDLE mode for DMA mode different of thresholdEduardo Valentin1-1/+9
Use dma mode property to configure NO IDLE or SMART IDLE of McBSPs. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Retain McBSP FCLK clockactivityEero Nurkkala2-3/+4
FCLK may get autogated so that it prevents the McBSP to work properly. It is the bit 9 that must be set for maintaining the McBSP FCLK. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Change wakeup signalsEduardo Valentin2-8/+2
Configure only XRDYEN and RRDYEN wakeup signals in order to get better power consumption. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Wakeups utilizedEero Nurkkala2-0/+63
This patch enables the smart idle mode while McBPS is being utilized. Once it's done, force idle mode is taken instead. Apart of it, it also configures what signals will wake mcbsp up. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Add link DMA mode selectionPeter Ujfalusi2-0/+92
It adds a new sysfs file, where the user can configure the mcbsp mode to use. If the mcbsp channel is in use, it does not allow the change. Than in omap_pcm_open we can call the omap_mcbsp_get_opmode to get the mode, store it, than use it to implement the different modes. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Rename thres sysfs symbolsEduardo Valentin1-10/+10
This patch renames the symbols that handles threshold sysfs properties. This way we can add more sysfs properties to them. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP3: McBSP: Lower the maximum buffersize for McBSP1, 3, 4, 5Peter Ujfalusi1-4/+4
Do not allow applications to use the full buffer found on McBSP1,3,4,5. Using the full buffer in threshold mode causes the McBSP buffer to run dry, which can be observed as channels are switching (in reality the channels are shifting). Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Create and export max_(r|t)x_thres propertyEduardo Valentin3-0/+138
This patch export through sysfs two properties to configure maximum threshold for transmission and reception on each mcbsp instance. Also, it exports two helper functions to allow mcbsp users to read this values. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Add transmit/receive threshold handlerEduardo Valentin2-0/+59
This patch adds a way to handle transmit/receive threshold. It export to mcbsp users a callback registration procedure. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Use appropriate value for startup delayEduardo Valentin1-1/+7
Increasing startup delay value as worst case: CLKSRG*2 = 8000khz: (1/8000) * 2 * 2 usec Although, 100us may give enough time for two CLKSRG, due to some unknown PM related, clock gating etc. reason, this patch increases it to 500us. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Add IRQEN, IRQSTATUS, THRESHOLD2 and THRESHOLD1 registers.Eduardo Valentin1-0/+4
Adding McBSP register definition for IRQEN, IRQSTATUS, THRESHOLD2 and THRESHOLD1 registers. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20OMAP: McBSP: Provide functions for ASoC frame syncronizationEero Nurkkala2-0/+54
ASoC has an annoying bug letting either L or R channel to be played on L channel. In other words, L and R channels can switch at random. This provides McBSP funtionality that may be used to fix this feature. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: Add SuperH FSI driver support for ALSAKuninori Morimoto4-1/+1095
This driver is very simple. It support playback only now. This patch is tested by ms7724se board. Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20ASoC: S3C24XX : Align the peroid size to the buffer sizeShine Liu1-0/+1
> Then it's a driver bug. If unaligned period size is allowed, it means > that the irq is really generated in that period, not at the buffer > boundary. Otherwise, it must have a proper hw-constraint to align the > period size to the buffer size. This patch will fix the bug metioned in the above mail. Force the peroid size to be aligned with the buffer size. Based and tested on linux-2.6.31-rc6. Signed-off-by: Shine Liu <shinel@foxmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-19ALSA: Restore support for DMAless DAIs on PXAMark Brown1-0/+3
Used for applications such as direct bluetooth connections on smartphones which don't go via the CPU. This used to be supported before the refactoring to share code but this check was removed during that move. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-19ASoC: Provide default set_bias_level() implementationMark Brown1-2/+6
If the CODEC does not provide a set_bias_level() then update the bias_level variable for it since other parts of the system expect that to be maintained. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 09:06:05 +0000