| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[This is upstream commit d3b9d7a9051d7024a93c76a84b2f84b3b66ad6d5.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 30efd8debd1ef30be342d374f01e993509f5b76b upstream
(dd54ec4067a23236736afecbda120030d7ce8fe9 in this tree) as it is not
needed for the 3.4-stable tree.
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[This is upstream commit 24a6078754f28528bc91e7e7b3e6ae86bd936d8.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[This is upstream commit 2d4fa940f99663c82ba55b2244638833b388e4e2.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[This is upstream commit 0fe51aa5eee51db7c7ecd201d42a977ad79c58b6.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset. It
uses ehci_cf_port_reset_rwsem to do this. USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs. It also makes the warm port reset code more complex.
Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a40e7cf8f06b4e322ba902e4e9f6a6b0c2daa907 upstream.
Commit 9f9c9cbb6057 ("drivers/firmware/dmi_scan.c: fetch dmi version
from SMBIOS if it exists") hoisted the check for "_DMI_" into
dmi_scan_machine(), which means that we don't bother to check for
"_DMI_" at offset 16 in an SMBIOS entry. smbios_present() may also call
dmi_present() for an address where we found "_SM_", if it failed further
validation.
Check for "_DMI_" in smbios_present() before calling dmi_present().
[akpm@linux-foundation.org: fix build]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: Tim McGrath <tmhikaru@gmail.com>
Tested-by: Tim Mcgrath <tmhikaru@gmail.com>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db05021d49a994ee40a9735d9c3cb0060c9babb8 upstream.
The prompt to enable DYNAMIC_FTRACE (the ability to nop and
enable function tracing at run time) had a confusing statement:
"enable/disable ftrace tracepoints dynamically"
This was written before tracepoints were added to the kernel,
but now that tracepoints have been added, this is very confusing
and has confused people enough to give wrong information during
presentations.
Not only that, I looked at the help text, and it still references
that dreaded daemon that use to wake up once a second to update
the nop locations and brick NICs, that hasn't been around for over
five years.
Time to bring the text up to the current decade.
Reported-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e37736777254ce1abc85493a5cacbefe5983b896 upstream.
When system enters sleep, non-boot CPUs will be disabled.
Cpufreq stats sysfs is created when the CPU is up, but it is not
freed when the CPU is going down. This will cause memory leak.
Signed-off-by: xiaobing tu <xiaobing.tu@intel.com>
Signed-off-by: guifang tang <guifang.tang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Colin Cross <ccross@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a930d8790552658140d7d0d2e316af4f0d76a512 upstream.
If you open a pipe for neither read nor write, the pipe code will not
add any usage counters to the pipe, causing the 'struct pipe_inode_info"
to be potentially released early.
That doesn't normally matter, since you cannot actually use the pipe,
but the pipe release code - particularly fasync handling - still expects
the actual pipe infrastructure to all be there. And rather than adding
NULL pointer checks, let's just disallow this case, the same way we
already do for the named pipe ("fifo") case.
This is ancient going back to pre-2.4 days, and until trinity, nobody
naver noticed.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
security keys
commit 8aec0f5d4137532de14e6554fd5dd201ff3a3c49 upstream.
Looking at mm/process_vm_access.c:process_vm_rw() and comparing it to
compat_process_vm_rw() shows that the compatibility code requires an
explicit "access_ok()" check before calling
compat_rw_copy_check_uvector(). The same difference seems to appear when
we compare fs/read_write.c:do_readv_writev() to
fs/compat.c:compat_do_readv_writev().
This subtle difference between the compat and non-compat requirements
should probably be debated, as it seems to be error-prone. In fact,
there are two others sites that use this function in the Linux kernel,
and they both seem to get it wrong:
Now shifting our attention to fs/aio.c, we see that aio_setup_iocb()
also ends up calling compat_rw_copy_check_uvector() through
aio_setup_vectored_rw(). Unfortunately, the access_ok() check appears to
be missing. Same situation for
security/keys/compat.c:compat_keyctl_instantiate_key_iov().
I propose that we add the access_ok() check directly into
compat_rw_copy_check_uvector(), so callers don't have to worry about it,
and it therefore makes the compat call code similar to its non-compat
counterpart. Place the access_ok() check in the same location where
copy_from_user() can trigger a -EFAULT error in the non-compat code, so
the ABI behaviors are alike on both compat and non-compat.
While we are here, fix compat_do_readv_writev() so it checks for
compat_rw_copy_check_uvector() negative return values.
And also, fix a memory leak in compat_keyctl_instantiate_key_iov() error
handling.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0da9dfdd2cd9889201bc6f6f43580c99165cd087 upstream.
This fixes CVE-2013-1792.
There is a race in install_user_keyrings() that can cause a NULL pointer
dereference when called concurrently for the same user if the uid and
uid-session keyrings are not yet created. It might be possible for an
unprivileged user to trigger this by calling keyctl() from userspace in
parallel immediately after logging in.
Assume that we have two threads both executing lookup_user_key(), both
looking for KEY_SPEC_USER_SESSION_KEYRING.
THREAD A THREAD B
=============================== ===============================
==>call install_user_keyrings();
if (!cred->user->session_keyring)
==>call install_user_keyrings()
...
user->uid_keyring = uid_keyring;
if (user->uid_keyring)
return 0;
<==
key = cred->user->session_keyring [== NULL]
user->session_keyring = session_keyring;
atomic_inc(&key->usage); [oops]
At the point thread A dereferences cred->user->session_keyring, thread B
hasn't updated user->session_keyring yet, but thread A assumes it is
populated because install_user_keyrings() returned ok.
The race window is really small but can be exploited if, for example,
thread B is interrupted or preempted after initializing uid_keyring, but
before doing setting session_keyring.
This couldn't be reproduced on a stock kernel. However, after placing
systemtap probe on 'user->session_keyring = session_keyring;' that
introduced some delay, the kernel could be crashed reliably.
Fix this by checking both pointers before deciding whether to return.
Alternatively, the test could be done away with entirely as it is checked
inside the mutex - but since the mutex is global, that may not be the best
way.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Mateusz Guzik <mguzik@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a5467bf7b6e9e02ec9c3da4e23747c05faeaac6 upstream.
Three errors resulting in kernel memory disclosure:
1/ The structures used for the netlink based crypto algorithm report API
are located on the stack. As snprintf() does not fill the remainder of
the buffer with null bytes, those stack bytes will be disclosed to users
of the API. Switch to strncpy() to fix this.
2/ crypto_report_one() does not initialize all field of struct
crypto_user_alg. Fix this to fix the heap info leak.
3/ For the module name we should copy only as many bytes as
module_name() returns -- not as much as the destination buffer could
hold. But the current code does not and therefore copies random data
from behind the end of the module name, as the module name is always
shorter than CRYPTO_MAX_ALG_NAME.
Also switch to use strncpy() to copy the algorithm's name and
driver_name. They are strings, after all.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c79c49826270b8b0061b2fca840fc3f013c8a78a upstream.
The git commit 8eaffa67b43e99ae581622c5133e20b0f48bcef1
(xen/pat: Disable PAT support for now) explains in details why
we want to disable PAT for right now. However that
change was not enough and we should have also disabled
the pat_enabled value. Otherwise we end up with:
mmap-example:3481 map pfn expected mapping type write-back for
[mem 0x00010000-0x00010fff], got uncached-minus
------------[ cut here ]------------
WARNING: at /build/buildd/linux-3.8.0/arch/x86/mm/pat.c:774 untrack_pfn+0xb8/0xd0()
mem 0x00010000-0x00010fff], got uncached-minus
------------[ cut here ]------------
WARNING: at /build/buildd/linux-3.8.0/arch/x86/mm/pat.c:774
untrack_pfn+0xb8/0xd0()
...
Pid: 3481, comm: mmap-example Tainted: GF 3.8.0-6-generic #13-Ubuntu
Call Trace:
[<ffffffff8105879f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff810587fa>] warn_slowpath_null+0x1a/0x20
[<ffffffff8104bcc8>] untrack_pfn+0xb8/0xd0
[<ffffffff81156c1c>] unmap_single_vma+0xac/0x100
[<ffffffff81157459>] unmap_vmas+0x49/0x90
[<ffffffff8115f808>] exit_mmap+0x98/0x170
[<ffffffff810559a4>] mmput+0x64/0x100
[<ffffffff810560f5>] dup_mm+0x445/0x660
[<ffffffff81056d9f>] copy_process.part.22+0xa5f/0x1510
[<ffffffff81057931>] do_fork+0x91/0x350
[<ffffffff81057c76>] sys_clone+0x16/0x20
[<ffffffff816ccbf9>] stub_clone+0x69/0x90
[<ffffffff816cc89d>] ? system_call_fastpath+0x1a/0x1f
---[ end trace 4918cdd0a4c9fea4 ]---
(a similar message shows up if you end up launching 'mcelog')
The call chain is (as analyzed by Liu, Jinsong):
do_fork
--> copy_process
--> dup_mm
--> dup_mmap
--> copy_page_range
--> track_pfn_copy
--> reserve_pfn_range
--> line 624: flags != want_flags
It comes from different memory types of page table (_PAGE_CACHE_WB) and MTRR
(_PAGE_CACHE_UC_MINUS).
Stefan Bader dug in this deep and found out that:
"That makes it clearer as this will do
reserve_memtype(...)
--> pat_x_mtrr_type
--> mtrr_type_lookup
--> __mtrr_type_lookup
And that can return -1/0xff in case of MTRR not being enabled/initialized. Which
is not the case (given there are no messages for it in dmesg). This is not equal
to MTRR_TYPE_WRBACK and thus becomes _PAGE_CACHE_UC_MINUS.
It looks like the problem starts early in reserve_memtype:
if (!pat_enabled) {
/* This is identical to page table setting without PAT */
if (new_type) {
if (req_type == _PAGE_CACHE_WC)
*new_type = _PAGE_CACHE_UC_MINUS;
else
*new_type = req_type & _PAGE_CACHE_MASK;
}
return 0;
}
This would be what we want, that is clearing the PWT and PCD flags from the
supported flags - if pat_enabled is disabled."
This patch does that - disabling PAT.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-and-Tested-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcd9006b1b053c7b1cebe81333261d4fd492ffeb upstream.
hid_output_raw_report() makes a direct call to usb_control_msg(). However,
some USB3 boards have shown that the usb device is not ready during the
.probe(). This blocks the entire usb device, and the paired mice, keyboards
are not functional. The dmesg output is the following:
[ 11.912287] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 11.912537] logitech-djreceiver 0003:046D:C52B.0003: logi_dj_probe:logi_dj_recv_query_paired_devices error:-32
[ 11.912636] logitech-djreceiver: probe of 0003:046D:C52B.0003 failed with error -32
Relying on the scheduled call to usbhid_submit_report() fixes the problem.
related bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1072082
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1039143
https://bugzilla.redhat.com/show_bug.cgi?id=840391
https://bugzilla.kernel.org/show_bug.cgi?id=49781
Reported-and-tested-by: Bob Bowles <bobjohnbowles@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e0855dff094b0d56d6b5b271e0ce7851cc1e063 upstream.
This patch removes redundant and unbalanced pci_disable_device() from
__e1000_shutdown(). pci_clear_master() is enough, device can go into
suspended state with elevated enable_cnt.
Bug was introduced in commit 23606cf5d1192c2b17912cb2ef6e62f9b11de133
("e1000e / PCI / PM: Add basic runtime PM support (rev. 4)") in v2.6.35
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2069d483b39a603a5f3428a19d3b4ac89aa97f48 upstream.
When a value of a vmaster slave control is changed, the ctl change
notification is sometimes ignored. This happens when the master
control overrides, e.g. when the corresponding master control is
muted. The reason is that slave_put() returns the value of the actual
slave put callback, and it doesn't reflect the virtual slave value
change.
This patch fixes the function just to return 1 whenever a slave value
is changed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69a4cfdd444d1fe5c24d29b3a063964ac165d2cd upstream.
Set card->private_data in snd_ice1712_create for fixing NULL
dereference in snd_ice1712_remove().
Signed-off-by: Sean Connor <sconnor004@allyinics.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2fe09b055e2549de41fb107b34c60bac4a1b0cf upstream.
Masked out PMXEVTYPER.NSH means that we can't enable profiling at PL2,
regardless of the settings in the HDCR.
This patch fixes the broken mask.
Reported-by: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8fc41377f5037ff7a661ea06adc05f1daec1548 upstream.
vbios values are wrong leading to colors that are
too bright. Use the default values instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f366fccd0809f13ba20d64cae3c83f7338c88af7 upstream.
We read the chip ID from the chip, use it to determine if the chip ID provided
to the driver is correct, and report it if wrong. We should also use the
correct chip ID to select supported functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dbd712c2272764a536e29ad6841dba74989a39d9 upstream.
Peak attributes were not initialized and cleared correctly.
Also, temp2_max is only supported on page 0 and thus does not need to be
an array.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e78080f81481aa8340374d5a37ae033c1cf4272 upstream.
Not having power is a pretty serious error so check that we are able to
enable the supply and error out if we can't.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
commit 58ebb34c49fcfcaa029e4b1c1453d92583900f9a upstream.
Create_stripe_zones returns an error slightly differently to
raid0_run and to raid0_takeover_*.
The error returned used by the second was wrong and an error would
result in mddev->private being set to NULL and sooner or later a
crash.
So never return NULL, return ERR_PTR(err), not NULL from
create_stripe_zones.
This bug has been present since 2.6.35 so the fix is suitable
for any kernel since then.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a64685399181780998281fe07309a94b25dd24c3 upstream.
You cannot resize a RAID0 array (in terms of making the devices
bigger), but the code doesn't entirely stop you.
So:
disable setting of the available size on each device for
RAID0 and Linear devices. This must not change as doing so
can change the effective layout of data.
Make sure that the size that raid0_size() reports is accurate,
but rounding devices sizes to chunk sizes. As the device sizes
cannot change now, this isn't so important, but it is best to be
safe.
Without this change:
mdadm --grow /dev/md0 -z max
mdadm --grow /dev/md0 -Z max
then read to the end of the array
can cause a BUG in a RAID0 array.
These bugs have been present ever since it became possible
to resize any device, which is a long time. So the fix is
suitable for any -stable kerenl.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbfa57c0f2243a7c31fd248d22e9861a2802cad5 upstream.
If an fsync occurs on a read-only array, we need to send a
completion for the IO and may not increment the active IO count.
Otherwise, we hit a bug trace and can't stop the MD array anymore.
By advice of Christoph Hellwig we return success upon a flush
request but we return -EROFS for other writes.
We detect flush requests by checking if the bio has zero sectors.
This patch is suitable to any -stable kernel to which it applies.
Signed-off-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: NeilBrown <neilb@suse.de>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3412f2f086ea7531378fabe756bd4a1109994ae6 upstream.
On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.
On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.
With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3d63cadbad97671d740a9698acc2c95d1ca6e79 upstream.
RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e7a4ff7c5b6423ddb644df9c41b8b6d2fb79d30 upstream.
Maximum delay for waking up card is 50 ms. Because of typo in
counter, this delay goes to 500ms. This patch fixes the bug.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7f154f1246ccc5a0a7e9ce50932627d60a0c878 upstream.
virtio_rng feeds the randomness buffer handed by the core directly
into the scatterlist, since commit bb347d98079a547e80bd4722dee1de61e4dca0e8.
However, if CONFIG_HW_RANDOM=m, the static buffer isn't a linear address
(at least on most archs). We could fix this in virtio_rng, but it's actually
far easier to just do it in the core as virtio_rng would have to allocate
a buffer every time (it doesn't know how much the core will want to read).
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9904344fc4052fbe7e4dc137eba0dcdadf326bd upstream.
An earlier commit cd006086fa5d91414d8ff9ff2b78fbb593878e3c ("ata_piix:
defer disks to the Hyper-V drivers by default") broke MS Virtual PC
guests. Hyper-V guests and Virtual PC guests have nearly identical DMI
info. As a result the driver does currently ignore the emulated hardware
in Virtual PC guests and defers the handling to hv_blkvsc. Since Virtual
PC does not offer paravirtualized drivers no disks will be found in the
guest.
One difference in the DMI info is the product version. This patch adds a
match for MS Virtual PC 2007 and "unignores" the emulated hardware.
This was reported for openSuSE 12.1 in bugzilla:
https://bugzilla.novell.com/show_bug.cgi?id=737532
Here is a detailed list of DMI info from example guests:
hwinfo --bios:
virtual pc guest:
System Info: #1
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "VS2005R2"
Serial: "3178-9905-1533-4840-9282-0569-59"
UUID: undefined, but settable
Wake-up: 0x06 (Power Switch)
Board Info: #2
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "5.0"
Serial: "3178-9905-1533-4840-9282-0569-59"
Chassis Info: #3
Manufacturer: "Microsoft Corporation"
Version: "5.0"
Serial: "3178-9905-1533-4840-9282-0569-59"
Asset Tag: "7188-3705-6309-9738-9645-0364-00"
Type: 0x03 (Desktop)
Bootup State: 0x03 (Safe)
Power Supply State: 0x03 (Safe)
Thermal State: 0x01 (Other)
Security Status: 0x01 (Other)
win2k8 guest:
System Info: #1
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "9106-3420-9819-5495-1514-2075-48"
UUID: undefined, but settable
Wake-up: 0x06 (Power Switch)
Board Info: #2
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "9106-3420-9819-5495-1514-2075-48"
Chassis Info: #3
Manufacturer: "Microsoft Corporation"
Version: "7.0"
Serial: "9106-3420-9819-5495-1514-2075-48"
Asset Tag: "7076-9522-6699-1042-9501-1785-77"
Type: 0x03 (Desktop)
Bootup State: 0x03 (Safe)
Power Supply State: 0x03 (Safe)
Thermal State: 0x01 (Other)
Security Status: 0x01 (Other)
win2k12 guest:
System Info: #1
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "8179-1954-0187-0085-3868-2270-14"
UUID: undefined, but settable
Wake-up: 0x06 (Power Switch)
Board Info: #2
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "8179-1954-0187-0085-3868-2270-14"
Chassis Info: #3
Manufacturer: "Microsoft Corporation"
Version: "7.0"
Serial: "8179-1954-0187-0085-3868-2270-14"
Asset Tag: "8374-0485-4557-6331-0620-5845-25"
Type: 0x03 (Desktop)
Bootup State: 0x03 (Safe)
Power Supply State: 0x03 (Safe)
Thermal State: 0x01 (Other)
Security Status: 0x01 (Other)
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9a6b52ee1baa865283a91eb8d443ee91adfca56 upstream.
If the socket is full, we're better off just waiting until it empties,
or until the connection is broken. The reason why we generally don't
want to time out is that the call to xprt->ops->release_xprt() will
trigger a connection reset, which isn't helpful...
Let's make an exception for soft RPC calls, since they have to provide
timeout guarantees.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a7a613a47a715711b3f2d3322a0eac21d459166 upstream.
Commit 73ca100 broke the code that prevents the client from deleting
a silly renamed dentry. This affected "delete on last close"
semantics as after that commit, nothing prevented removal of
silly-renamed files. As a result, a process holding a file open
could easily get an ESTALE on the file in a directory where some
other process issued 'rm -rf some_dir_containing_the_file' twice.
Before the commit, any attempt at unlinking silly renamed files would
fail inside may_delete() with -EBUSY because of the
DCACHE_NFSFS_RENAMED flag. The following testcase demonstrates
the problem:
tail -f /nfsmnt/dir/file &
rm -rf /nfsmnt/dir
rm -rf /nfsmnt/dir
# second removal does not fail, 'tail' process receives ESTALE
The problem with the above commit is that it unhashes the old and
new dentries from the lookup path, even in the normal case when
a signal is not encountered and it would have been safe to call
d_move. Unfortunately the old dentry has the special
DCACHE_NFSFS_RENAMED flag set on it. Unhashing has the
side-effect that future lookups call d_alloc(), allocating a new
dentry without the special flag for any silly-renamed files. As a
result, subsequent calls to unlink silly renamed files do not fail
but allow the removal to go through. This will result in ESTALE
errors for any other process doing operations on the file.
To fix this, go back to using d_move on success.
For the signal case, it's unclear what we may safely do beyond d_drop.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce2ac52105aa663056dfc17966ebed1bf93e6e64 upstream.
Kjell Braden reported this oops:
[ 833.211970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 833.212816] IP: [< (null)>] (null)
[ 833.213280] PGD 1b9b2067 PUD e9f7067 PMD 0
[ 833.213874] Oops: 0010 [#1] SMP
[ 833.214344] CPU 0
[ 833.214458] Modules linked in: des_generic md4 nls_utf8 cifs vboxvideo drm snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq bnep rfcomm snd_timer bluetooth snd_seq_device ppdev snd vboxguest parport_pc joydev mac_hid soundcore snd_page_alloc psmouse i2c_piix4 serio_raw lp parport usbhid hid e1000
[ 833.215629]
[ 833.215629] Pid: 1752, comm: mount.cifs Not tainted 3.0.0-rc7-bisectcifs-fec11dd9a0+ #18 innotek GmbH VirtualBox/VirtualBox
[ 833.215629] RIP: 0010:[<0000000000000000>] [< (null)>] (null)
[ 833.215629] RSP: 0018:ffff8800119c9c50 EFLAGS: 00010282
[ 833.215629] RAX: ffffffffa02186c0 RBX: ffff88000c427780 RCX: 0000000000000000
[ 833.215629] RDX: 0000000000000000 RSI: ffff88000c427780 RDI: ffff88000c4362e8
[ 833.215629] RBP: ffff8800119c9c88 R08: ffff88001fc15e30 R09: 00000000d69515c7
[ 833.215629] R10: ffffffffa0201972 R11: ffff88000e8f6a28 R12: ffff88000c4362e8
[ 833.215629] R13: 0000000000000000 R14: 0000000000000000 R15: ffff88001181aaa6
[ 833.215629] FS: 00007f2986171700(0000) GS:ffff88001fc00000(0000) knlGS:0000000000000000
[ 833.215629] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 833.215629] CR2: 0000000000000000 CR3: 000000001b982000 CR4: 00000000000006f0
[ 833.215629] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 833.215629] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 833.215629] Process mount.cifs (pid: 1752, threadinfo ffff8800119c8000, task ffff88001c1c16f0)
[ 833.215629] Stack:
[ 833.215629] ffffffff8116a9b5 ffff8800119c9c88 ffffffff81178075 0000000000000286
[ 833.215629] 0000000000000000 ffff88000c4276c0 ffff8800119c9ce8 ffff8800119c9cc8
[ 833.215629] ffffffff8116b06e ffff88001bc6fc00 ffff88000c4276c0 ffff88000c4276c0
[ 833.215629] Call Trace:
[ 833.215629] [<ffffffff8116a9b5>] ? d_alloc_and_lookup+0x45/0x90
[ 833.215629] [<ffffffff81178075>] ? d_lookup+0x35/0x60
[ 833.215629] [<ffffffff8116b06e>] __lookup_hash.part.14+0x9e/0xc0
[ 833.215629] [<ffffffff8116b1d6>] lookup_one_len+0x146/0x1e0
[ 833.215629] [<ffffffff815e4f7e>] ? _raw_spin_lock+0xe/0x20
[ 833.215629] [<ffffffffa01eef0d>] cifs_do_mount+0x26d/0x500 [cifs]
[ 833.215629] [<ffffffff81163bd3>] mount_fs+0x43/0x1b0
[ 833.215629] [<ffffffff8117d41a>] vfs_kern_mount+0x6a/0xd0
[ 833.215629] [<ffffffff8117e584>] do_kern_mount+0x54/0x110
[ 833.215629] [<ffffffff8117fdc2>] do_mount+0x262/0x840
[ 833.215629] [<ffffffff81108a0e>] ? __get_free_pages+0xe/0x50
[ 833.215629] [<ffffffff8117f9ca>] ? copy_mount_options+0x3a/0x180
[ 833.215629] [<ffffffff8118075d>] sys_mount+0x8d/0xe0
[ 833.215629] [<ffffffff815ece82>] system_call_fastpath+0x16/0x1b
[ 833.215629] Code: Bad RIP value.
[ 833.215629] RIP [< (null)>] (null)
[ 833.215629] RSP <ffff8800119c9c50>
[ 833.215629] CR2: 0000000000000000
[ 833.238525] ---[ end trace ec00758b8d44f529 ]---
When walking down the path on the server, it's possible to hit a
symlink. The path walking code assumes that the caller will handle that
situation properly, but cifs_get_root() isn't set up for it. This patch
prevents the oops by simply returning an error.
A better solution would be to try and chase the symlinks here, but that's
fairly complicated to handle.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=53221
Reported-and-tested-by: Kjell Braden <afflux@pentabarf.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cba0cdf5e4dbcd9e5fa5b54d7a028e55e2ca057 upstream.
__btrfs_close_devices() clones btrfs device structs with
memcpy(). Some of the fields in the clone are reinitialized, but it's
missing to init io_lock. In mainline this goes unnoticed, but on RT it
leaves the plist pointing to the original about to be freed lock
struct.
Initialize io_lock after cloning, so no references to the original
struct are left.
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 472b72f2db7831d7dbe22ffdff4adee3bd49b05d upstream.
The page++ is wrong. It makes bio_add_pc_page() pointing to a wrong page
address if the 'while (len > 0 && data_len > 0) { ... }' loop is
executed more than one once.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9d2696e658ef4f209955ddaa987d43f1a1bd81a1 upstream.
Properly initialize scatterlist before using it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 208afec4f3be8c51ad6eebe6611dd6d2ad2fa298 upstream.
This bug was introduced back in bitkeeper days in 2003. We use
"dcb->dev_mode" before it has been initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 884ac2978a295b7df3c4a686d3bff6932bbbb460 upstream.
There is no hypercall to setup multiple MSI per PCI device.
As such with these two new commits:
- 08261d87f7d1b6253ab3223756625a5c74532293
PCI/MSI: Enable multiple MSIs with pci_enable_msi_block_auto()
- 5ca72c4f7c412c2002363218901eba5516c476b1
AHCI: Support multiple MSIs
we would call the PHYSDEVOP_map_pirq 'nvec' times with the same
contents of the PCI device. Sander discovered that we would get
the same PIRQ value 'nvec' times and return said values to the
caller. That of course meant that the device was configured only
with one MSI and AHCI would fail with:
ahci 0000:00:11.0: version 3.0
xen: registering gsi 19 triggering 0 polarity 1
xen: --> pirq=19 -> irq=19 (gsi=19)
(XEN) [2013-02-27 19:43:07] IOAPIC[0]: Set PCI routing entry (6-19 -> 0x99 -> IRQ 19 Mode:1 Active:1)
ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
ahci: probe of 0000:00:11.0 failed with error -22
That is b/c in ahci_host_activate the second call to
devm_request_threaded_irq would return -EINVAL as we passed in
(on the second run) an IRQ that was never initialized.
Reported-and-Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b255188f90e2bade1bd11a986dd1ca4861869f4d upstream.
Paolo Pisati reports that IPv6 triggers this warning:
BUG: scheduling while atomic: swapper/0/0/0x40000100
Modules linked in:
[<c001b1c4>] (unwind_backtrace+0x0/0xf0) from [<c0503c5c>] (__schedule_bug+0x48/0x5c)
[<c0503c5c>] (__schedule_bug+0x48/0x5c) from [<c0508608>] (__schedule+0x700/0x740)
[<c0508608>] (__schedule+0x700/0x740) from [<c007007c>] (__cond_resched+0x24/0x34)
[<c007007c>] (__cond_resched+0x24/0x34) from [<c05086dc>] (_cond_resched+0x3c/0x44)
[<c05086dc>] (_cond_resched+0x3c/0x44) from [<c0021f6c>] (do_alignment+0x178/0x78c)
[<c0021f6c>] (do_alignment+0x178/0x78c) from [<c00083e0>] (do_DataAbort+0x34/0x98)
[<c00083e0>] (do_DataAbort+0x34/0x98) from [<c0509a60>] (__dabt_svc+0x40/0x60)
Exception stack(0xc0763d70 to 0xc0763db8)
3d60: e97e805e e97e806e 2c000000 11000000
3d80: ea86bb00 0000002c 00000011 e97e807e c076d2a8 e97e805e e97e806e 0000002c
3da0: 3d000000 c0763dbc c04b98fc c02a8490 00000113 ffffffff
[<c0509a60>] (__dabt_svc+0x40/0x60) from [<c02a8490>] (__csum_ipv6_magic+0x8/0xc8)
Fix this by using probe_kernel_address() stead of __get_user().
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Tested-by: Paolo Pisati <p.pisati@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e4ba617c1b584b2e376f31a63bd4e734109318a upstream.
Martin Storsjö reports that the sequence:
ee312ac1 vsub.f32 s4, s3, s2
ee702ac0 vsub.f32 s5, s1, s0
e59f0028 ldr r0, [pc, #40]
ee111a90 vmov r1, s3
on Raspberry Pi (implementor 41 architecture 1 part 20 variant b rev 5)
where s3 is a denormal and s2 is zero results in incorrect behaviour -
the instruction "vsub.f32 s5, s1, s0" is not executed:
VFP: bounce: trigger ee111a90 fpexc d0000780
VFP: emulate: INST=0xee312ac1 SCR=0x00000000
...
As we can see, the instruction triggering the exception is the "vmov"
instruction, and we emulate the "vsub.f32 s4, s3, s2" but fail to
properly take account of the FPEXC_FP2V flag in FPEXC. This is because
the test for the second instruction register being valid is bogus, and
will always skip emulation of the second instruction.
Reported-by: Martin Storsjö <martin@martin.st>
Tested-by: Martin Storsjö <martin@martin.st>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 0322bd3980b3ebf7dde8474e22614cb443d6479a upstream.
Don't let Masterkit MA901 USB radio be handled by usb hid drivers.
This device will be handled by radio-ma901.c driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3aee8bc52c415aba8148f144e5e5359b0fd75dd1 upstream.
This patch adds the IDE-mode SATA Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aaa515277db9585eeb4fdeb4637b9f9df50a1dd9 upstream.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85df3b3769222894e9692b383c7af124b7721086 upstream.
The %name-prefix "prefix" syntax is not available on bison 2.3 and
older. Substitute with the -p "prefix" command-line option for
compatibility with older versions of bison.
This patch fixes this build error with older versions of bison.
CC util/sysfs.o
BISON util/pmu-bison.c
util/pmu.y:2.14-24: syntax error, unexpected string, expecting =
make: *** [util/pmu-bison.c] Error 1
Signed-off-by: Vinson Lee <vlee@twitter.com>
Tested-by: Li Zefan <lizefan@huawei.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1360792138-29186-1-git-send-email-vlee@twitter.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc400e185c07c15a42d2635995f422de5b94b696 upstream.
Some low-level comedi drivers (incorrectly) point `dev->read_subdev` or
`dev->write_subdev` to a subdevice that does not support asynchronous
commands. Comedi's poll(), read() and write() file operation handlers
assume these subdevices do support asynchronous commands. In
particular, they assume `s->async` is valid (where `s` points to the
read or write subdevice), which it won't be if it has been set
incorrectly. This can lead to a NULL pointer dereference.
Check `s->async` is non-NULL in `comedi_poll()`, `comedi_read()` and
`comedi_write()` to avoid the bug.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 22056e2b46246d97ff0f7c6e21a77b8daa07f02c upstream.
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems that writing to the command3 register after writing to the
command4 register in `labpc_ai_cmd()` messes up the differential
reference bit setting in the command4 register. Set up the command4
register after the command3 register (as in `labpc_ai_rinsn()`) to avoid
the problem.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 4c4bc25d0fa6beaf054c0b4c3b324487f266c820 upstream.
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems the setting of the channel bits for particular scanning modes
was incorrect for differential mode. (Only half the number of channels
are available in differential mode; comedi refers to them as channels 0,
1, 2 and 3, but the hardware documentation refers to them as channels 0,
2, 4 and 6.) In differential mode, the setting of the channel enable
bits in the command1 register should depend on whether the scan enable
bit is set. Effectively, we need to double the comedi channel number
when the scan enable bit is not set in differential mode. The scan
enable bit gets set when the AI scan mode is `MODE_MULT_CHAN_UP` or
`MODE_MULT_CHAN_DOWN`, and gets cleared when the AI scan mode is
`MODE_SINGLE_CHAN` or `MODE_SINGLE_CHAN_INTERVAL`. The existing test
for whether the comedi channel number needs to be doubled in
differential mode is incorrect in `labpc_ai_cmd()`. This patch corrects
the test.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66f2fda93b67fa744d406e6dcf443f67bac204b6 upstream.
This patch adds a quirk to allow the Sony VGN-FW41E_H to suspend/resume
properly.
References: http://bugs.launchpad.net/bugs/1113547
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eeb0751c99522a4d1bbcc7b6bc1460cd07d07488 upstream.
Power supply subsystem creates thermal zone device for the property
'POWER_SUPPLY_PROP_TEMP' which requires thermal subsystem to be ready
before 'ab8500 battery temperature monitor' driver is initialized. ab8500
btemp driver is initialized with subsys_initcall whereas thermal subsystem
is initialized with fs_initcall which causes
thermal_zone_device_register(...) to crash since the required structure
'thermal_class' is not initialized yet:
Unable to handle kernel NULL pointer dereference at virtual address 000000a4
pgd = c0004000
[000000a4] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 Tainted: G W (3.8.0-rc4-00001-g632fda8-dirty #1)
PC is at _raw_spin_lock+0x18/0x54
LR is at get_device_parent+0x50/0x1b8
pc : [<c02f1dd0>] lr : [<c01cb248>] psr: 60000013
sp : ef04bdc8 ip : 00000000 fp : c0446180
r10: ef216e38 r9 : c03af5d0 r8 : ef275c18
r7 : 00000000 r6 : c0476c14 r5 : ef275c18 r4 : ef095840
r3 : ef04a000 r2 : 00000001 r1 : 00000000 r0 : 000000a4
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 0000404a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xef04a238)
Stack: (0xef04bdc8 to 0xef04c000)
[...]
[<c02f1dd0>] (_raw_spin_lock+0x18/0x54) from [<c01cb248>] (get_device_parent+0x50/0x1b8)
[<c01cb248>] (get_device_parent+0x50/0x1b8) from [<c01cb8d8>] (device_add+0xa4/0x574)
[<c01cb8d8>] (device_add+0xa4/0x574) from [<c020b91c>] (thermal_zone_device_register+0x118/0x938)
[<c020b91c>] (thermal_zone_device_register+0x118/0x938) from [<c0202030>] (power_supply_register+0x170/0x1f8)
[<c0202030>] (power_supply_register+0x170/0x1f8) from [<c02055ec>] (ab8500_btemp_probe+0x208/0x47c)
[<c02055ec>] (ab8500_btemp_probe+0x208/0x47c) from [<c01cf0dc>] (platform_drv_probe+0x14/0x18)
[<c01cf0dc>] (platform_drv_probe+0x14/0x18) from [<c01cde70>] (driver_probe_device+0x74/0x20c)
[<c01cde70>] (driver_probe_device+0x74/0x20c) from [<c01ce094>] (__driver_attach+0x8c/0x90)
[<c01ce094>] (__driver_attach+0x8c/0x90) from [<c01cc640>] (bus_for_each_dev+0x4c/0x80)
[<c01cc640>] (bus_for_each_dev+0x4c/0x80) from [<c01cd6b4>] (bus_add_driver+0x16c/0x23c)
[<c01cd6b4>] (bus_add_driver+0x16c/0x23c) from [<c01ce54c>] (driver_register+0x78/0x14c)
[<c01ce54c>] (driver_register+0x78/0x14c) from [<c00086ac>] (do_one_initcall+0xfc/0x164)
[<c00086ac>] (do_one_initcall+0xfc/0x164) from [<c02e89c8>] (kernel_init+0x120/0x2b8)
[<c02e89c8>] (kernel_init+0x120/0x2b8) from [<c000e358>] (ret_from_fork+0x14/0x3c)
Code: e3c3303f e5932004 e2822001 e5832004 (e1903f9f)
---[ end trace ed9df72941b5bada ]---
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
