| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.
On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.
This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.com
Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
If we select a symbol it should have a type declared first
otherwise in some situations the config tools get upset. They
are currently perhaps a bit too resilient which is why this
wasn't noticed initially.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111206132811.4041.32549.stgit@bob.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
We currently fail to build on CONFIG_X86_INTEL_MID=y and
CONFIG_X86_MRST unset.
We could build all the bits to make generic MID work if you
picked MID platform alone but that's really silly. Instead use
select and two variables.
This looks a bit daft right now but once we add a Medfield
selection it'll start to look a good deal more sensible.
Reported-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111205231433.28811.51297.stgit@bob.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intr_remapping: Fix section mismatch in ir_dev_scope_init()
intel-iommu: Fix section mismatch in dmar_parse_rmrr_atsr_dev()
x86, amd: Fix up numa_node information for AMD CPU family 15h model 0-0fh northbridge functions
x86, AMD: Correct align_va_addr documentation
x86/rtc, mrst: Don't register a platform RTC device for for Intel MID platforms
x86/mrst: Battery fixes
x86/paravirt: PTE updates in k(un)map_atomic need to be synchronous, regardless of lazy_mmu mode
x86: Fix "Acer Aspire 1" reboot hang
x86/mtrr: Resolve inconsistency with Intel processor manual
x86: Document rdmsr_safe restrictions
x86, microcode: Fix the failure path of microcode update driver init code
Add TAINT_FIRMWARE_WORKAROUND on MTRR fixup
x86/mpparse: Account for bus types other than ISA and PCI
x86, mrst: Change the pmic_gpio device type to IPC
mrst: Added some platform data for the SFI translations
x86,mrst: Power control commands update
x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot
x86, UV: Fix UV2 hub part number
x86: Add user_mode_vm check in stack_overflow_check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix loss of notification with multi-event
perf, x86: Force IBS LVT offset assignment for family 10h
perf, x86: Disable PEBS on SandyBridge chips
trace_events_filter: Use rcu_assign_pointer() when setting ftrace_event_call->filter
perf session: Fix crash with invalid CPU list
perf python: Fix undefined symbol problem
perf/x86: Enable raw event access to Intel offcore events
perf: Don't use -ENOSPC for out of PMU resources
perf: Do not set task_ctx pointer in cpuctx if there are no events in the context
perf/x86: Fix PEBS instruction unwind
oprofile, x86: Fix crash when unloading module (nmi timer mode)
oprofile: Fix crash when unloading module (hr timer mode)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Set noop handler in clockevents_exchange_device()
tick-broadcast: Stop active broadcast device when replacing it
clocksource: Fix bug with max_deferment margin calculation
rtc: Fix some bugs that allowed accumulating time drift in suspend/resume
rtc: Disable the alarm in the hardware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
slab, lockdep: Fix silly bug
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix race condition when stopping the irq thread
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched, x86: Avoid unnecessary overflow in sched_clock
sched: Fix buglet in return_cfs_rq_runtime()
sched: Avoid SMT siblings in select_idle_sibling() if possible
sched: Set the command name of the idle tasks in SMP kernels
sched, rt: Provide means of disabling cross-cpu bandwidth sharing
sched: Document wait_for_completion_*() return values
sched_fair: Fix a typo in the comment describing update_sd_lb_stats
sched: Add a comment to effective_load() since it's a pain
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] ap: Setup timer for sending messages after reset.
[S390] cio: fix chsc_chp_vary
[S390] cio: provide fake irb for transport mode IO
[S390] cio: disallow driver io for known to be broken paths
[S390] hibernate: directly trigger subchannel evaluation
[S390] remove reset of system call restart on psw changes
[S390] add missing .set function for NT_S390_LAST_BREAK regset
[S390] fix page change underindication in pgste_update_all
[S390] ptrace inferior call interactions with TIF_SYSCALL
[S390] kdump: Replace is_kdump_kernel() with OLDMEM_BASE check
|
|
I screwed up by compiling that driver for the machine rather
than the arch. Correcting this fixes the build error.
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix:
Section mismatch in reference from the function
ir_dev_scope_init() to the function
.init.text:dmar_dev_scope_init() The function
ir_dev_scope_init() references the function __init dmar_dev_scope_init().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Youquan Song <youquan.song@intel.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Link: http://lkml.kernel.org/r/20111026161507.GB10103@swordfish
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
dmar_parse_rmrr_atsr_dev() calls rmrr_parse_dev() and
atsr_parse_dev() which are both marked as __init.
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Link: http://lkml.kernel.org/r/20111026154539.GA10103@swordfish
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
northbridge functions
I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.
Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Commit dfb09f9b7ab0 ("x86, amd: Avoid cache aliasing penalties
on AMD family 15h") introduced a kernel command line parameter
called 'align_va_addr' which still refers to arguments used in
an earlier version of the patch and which got changed without
updating the documentation. Correct that omission.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Link: http://lkml.kernel.org/r/1321873819-29541-1-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Intel MID x86 platforms have a memory mapped virtual RTC
instead. No MID platform have the default ports (and
accessing them may do weird stuff).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: feng.tang@intel.com
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When DCDC input line over current detecting, PMIC will change
charging current automatically. Logging event is enough.
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
[fix build]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
regardless of lazy_mmu mode
Fix an outstanding issue that has been reported since 2.6.37.
Under a heavy loaded machine processing "fork()" calls could
crash with:
BUG: unable to handle kernel paging request at f573fc8c
IP: [<c01abc54>] swap_count_continued+0x104/0x180
*pdpt = 000000002a3b9027 *pde = 0000000001bed067 *pte = 0000000000000000 Oops: 0000 [#1] SMP
Modules linked in:
Pid: 1638, comm: apache2 Not tainted 3.0.4-linode37 #1
EIP: 0061:[<c01abc54>] EFLAGS: 00210246 CPU: 3
EIP is at swap_count_continued+0x104/0x180
.. snip..
Call Trace:
[<c01ac222>] ? __swap_duplicate+0xc2/0x160
[<c01040f7>] ? pte_mfn_to_pfn+0x87/0xe0
[<c01ac2e4>] ? swap_duplicate+0x14/0x40
[<c01a0a6b>] ? copy_pte_range+0x45b/0x500
[<c01a0ca5>] ? copy_page_range+0x195/0x200
[<c01328c6>] ? dup_mmap+0x1c6/0x2c0
[<c0132cf8>] ? dup_mm+0xa8/0x130
[<c013376a>] ? copy_process+0x98a/0xb30
[<c013395f>] ? do_fork+0x4f/0x280
[<c01573b3>] ? getnstimeofday+0x43/0x100
[<c010f770>] ? sys_clone+0x30/0x40
[<c06c048d>] ? ptregs_clone+0x15/0x48
[<c06bfb71>] ? syscall_call+0x7/0xb
The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:
map = kmap_atomic(page, KM_USER0) + offset;
and then later we touch *map.
Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.
Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.
Interestingly, commit b8bcfe997e4615 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
into x86/urgent
|
|
Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails. It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).
There's a log of problems at:
https://bbs.archlinux.org/viewtopic.php?id=124136
This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: Uroš Vampl <mobile.leecher@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Following is from Notes of section 11.5.3 of Intel processor
manual available at:
http://www.intel.com/Assets/PDF/manual/325384.pdf
For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.
This patch provides resolution for that.
Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace into perf/urgent
|
|
Recently, I got bitten by using rdmsr_safe too early in the boot
process. Document its shortcomings for future reference.
Link: http://lkml.kernel.org/r/4ED5B70F.606@lwfinger.net
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
The microcode update driver's initialization code does not handle
failures correctly. This patch fixes this issue.
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20111107123530.12164.31227.stgit@srivatsabhat.in.ibm.com
Link: http://lkml.kernel.org/r/4ED8E2270200007800065120@nat28.tlf.novell.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
TAINT_FIRMWARE_WORKAROUND should be set when an MTRR fixup
is done.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1318958650-12447-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In commit f8924e770e04 ("x86: unify mp_bus_info"), the 32-bit
and 64-bit versions of MP_bus_info were rearranged to match each
other better. Unfortunately it introduced a regression: prior
to that change we used to always set the mp_bus_not_pci bit,
then clear it if we found a PCI bus. After it, we set
mp_bus_not_pci for ISA buses, clear it for PCI buses, and leave
it alone otherwise.
In the cases of ISA and PCI, there's not much difference. But
ISA is not the only non-PCI bus, so it's better to always set
mp_bus_not_pci and clear it only for PCI.
Without this change, Dan's Dell PowerEdge 4200 panics on boot
with a log indicating interrupt routing trouble unless the
"noapic" option is supplied. With this change, the machine
boots reliably without "noapic".
Fixes http://bugs.debian.org/586494
Reported-bisected-and-tested-by: Dan McGrath <troubledaemon@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 2.6.26+
Cc: Dan McGrath <troubledaemon@gmail.com>
Cc: Alexey Starikovskiy <aystarik@gmail.com>
[jrnieder@gmail.com: clarified commit message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Link: http://lkml.kernel.org/r/20111122215000.GA9151@elie.hsd1.il.comcast.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In latest firmware's SFI tables, pmic_gpio has been set to
IPC type of device, so we need handle it too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add SFI glue for the following devices:
tca6416: a gpio expander compatible with max7315
mpu3050: gyro sensor
Both of these actual drivers are already upstream
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
On the Intel MID devices SCU commands are issued to manage power
off and the like. We need to issue different ones for
non-Lincroft based devices.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Dell OptiPlex 990 is known to require PCI reboot, so add it to
the reboot blacklist in pci_reboot_dmi_table[].
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/201111160019.51303.rjw@sisk.pl
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There was a mixup when the SGI UV2 hub chip was sent to be
fabricated, and it ended up with the wrong part number in the
HRP_NODE_ID mmr. Future versions of the chip will (may) have the
correct part number. Change the UV infrastructure to recognize
both part numbers as valid IDs of a UV2 hub chip.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20111129210058.GA20452@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The kernel stack overflow is checked in stack_overflow_check(),
which may wrongly detect the overflow if the stack pointer in
user space points to the kernel stack intentionally or
accidentally. So, the actual overflow is never detected after
this misdetection because WARN_ONCE() is used on the detection
of it.
This patch adds user-mode-vm checking before it to avoid this
problem and bails out early if the user stack is used.
Signed-off-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Randy Dunlap <rdunlap@xenotime.net>
Link: http://lkml.kernel.org/r/20111129060821.11076.55315.stgit@ltc219.sdl.hitachi.co.jp
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
|
|
Commit 30765b92 ("slab, lockdep: Annotate the locks before using
them") moves the init_lock_keys() call from after g_cpucache_up =
FULL, to before it. And overlooks the fact that init_node_lock_keys()
tests for it and ignores everything !FULL.
Introduce a LATE stage and change the lockdep test to be <LATE.
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When you do:
$ perf record -e cycles,cycles,cycles noploop 10
You expect about 10,000 samples for each event, i.e., 10s at
1000samples/sec. However, this is not what's happening. You
get much fewer samples, maybe 3700 samples/event:
$ perf report -D | tail -15
Aggregated stats:
TOTAL events: 10998
MMAP events: 66
COMM events: 2
SAMPLE events: 10930
cycles stats:
TOTAL events: 3644
SAMPLE events: 3644
cycles stats:
TOTAL events: 3642
SAMPLE events: 3642
cycles stats:
TOTAL events: 3644
SAMPLE events: 3644
On a Intel Nehalem or even AMD64, there are 4 counters capable
of measuring cycles, so there is plenty of space to measure those
events without multiplexing (even with the NMI watchdog active).
And even with multiplexing, we'd expect roughly the same number
of samples per event.
The root of the problem was that when the event that caused the buffer
to become full was not the first event passed on the cmdline, the user
notification would get lost. The notification was sent to the file
descriptor of the overflowed event but the perf tool was not polling
on it. The perf tool aggregates all samples into a single buffer,
i.e., the buffer of the first event. Consequently, it assumes
notifications for any event will come via that descriptor.
The seemingly straight forward solution of moving the waitq into the
ringbuffer object doesn't work because of life-time issues. One could
perf_event_set_output() on a fd that you're also blocking on and cause
the old rb object to be freed while its waitq would still be
referenced by the blocked thread -> FAIL.
Therefore link all events to the ringbuffer and broadcast the wakeup
from the ringbuffer object to all possible events that could be waited
upon. This is rather ugly, and we're open to better solutions but it
works for now.
Reported-by: Stephane Eranian <eranian@google.com>
Finished-by: Stephane Eranian <eranian@google.com>
Reviewed-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111126014731.GA7030@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
On AMD family 10h we see firmware bug messages like the following:
[Firmware Bug]: cpu 6, try to use APIC500 (LVT offset 0) for vector 0x10400, but the register is already in use for vector 0xf9 on another cpu
[Firmware Bug]: cpu 6, IBS interrupt offset 0 not available (MSRC001103A=0x0000000000000100)
[Firmware Bug]: using offset 1 for IBS interrupts
[Firmware Bug]: workaround enabled for IBS LVT offset
perf: AMD IBS detected (0x00000007)
We always see this, since the offsets are not assigned by the BIOS for
this family. Force LVT offset assignment in this case. If the OS
assignment fails, fallback to BIOS settings and try to setup this.
The fallback to BIOS settings weakens the family check since
force_ibs_eilvt_setup() may fail e.g. in case of virtual machines.
But setup may still succeed if BIOS offsets are correct.
Other families don't have a workaround implemented that assigns LVT
offsets. It's ok, to drop calling force_ibs_eilvt_setup() for that
families.
With the patch the [Firmware Bug] messages vanish. We see now:
IBS: LVT offset 1 assigned
perf: AMD IBS detected (0x00000007)
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111109162225.GO12451@erda.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Cc: Stephane Eranian <eranian@google.com>
Cc: stable@kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
People with old AMD chips are getting hung boots, because commit
bcb80e53877c ("x86, microcode, AMD: Add microcode revision to
/proc/cpuinfo") moved the microcode detection too early into
"early_init_amd()".
At that point we are *so* early in the booth that the exception tables
haven't even been set up yet, so the whole
rdmsr_safe(MSR_AMD64_PATCH_LEVEL, &c->microcode, &dummy);
doesn't actually work: if the rdmsr does a GP fault (due to non-existant
MSR register on older CPU's), we can't fix it up yet, and the boot fails.
Fix it by simply moving the code to a slightly later point in the boot
(init_amd() instead of early_init_amd()), since the kernel itself
doesn't even really care about the microcode patchlevel at this point
(or really ever: it's made available to user space in /proc/cpuinfo, and
updated if you do a microcode load).
Reported-tested-and-bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Bob Tracy <rct@gherkin.frus.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The idea behind commit d91ee5863b71 ("cpuidle: replace xen access to x86
pm_idle and default_idle") was to have one call - disable_cpuidle()
which would make pm_idle not be molested by other code. It disallows
cpuidle_idle_call to be set to pm_idle (which is excellent).
But in the select_idle_routine() and idle_setup(), the pm_idle can still
be set to either: amd_e400_idle, mwait_idle or default_idle. This
depends on some CPU flags (MWAIT) and in AMD case on the type of CPU.
In case of mwait_idle we can hit some instances where the hypervisor
(Amazon EC2 specifically) sets the MWAIT and we get:
Brought up 2 CPUs
invalid opcode: 0000 [#1] SMP
Pid: 0, comm: swapper Not tainted 3.1.0-0.rc6.git0.3.fc16.x86_64 #1
RIP: e030:[<ffffffff81015d1d>] [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
...
Call Trace:
[<ffffffff8100e2ed>] cpu_idle+0xae/0xe8
[<ffffffff8149ee78>] cpu_bringup_and_idle+0xe/0x10
RIP [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
RSP <ffff8801d28ddf10>
In the case of amd_e400_idle we don't get so spectacular crashes, but we
do end up making an MSR which is trapped in the hypervisor, and then
follow it up with a yield hypercall. Meaning we end up going to
hypervisor twice instead of just once.
The previous behavior before v3.0 was that pm_idle was set to
default_idle regardless of select_idle_routine/idle_setup.
We want to do that, but only for one specific case: Xen. This patch
does that.
Fixes RH BZ #739499 and Ubuntu #881076
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: ftdi_sio: add PID for Propox ISPcable III
Revert "xHCI: reset-on-resume quirk for NEC uPD720200"
xHCI: fix bug in xhci_clear_command_ring()
usb: gadget: fsl_udc: fix dequeuing a request in progress
usb: fsl_mxc_udc.c: Remove compile-time dependency of MX35 SoC type
usb: fsl_mxc_udc.c: Fix build issue by including missing header file
USB: fsl_udc_core: use usb_endpoint_xfer_isoc to judge ISO XFER
usb: udc: Fix gadget driver's speed check in various UDC drivers
usb: gadget: fix g_serial regression
usb: renesas_usbhs: fixup driver speed
usb: renesas_usbhs: fixup gadget.dev.driver when udc_stop.
usb: renesas_usbhs: fixup signal the driver that cable was disconnected
usb: renesas_usbhs: fixup device_register timing
usb: musb: PM: fix context save/restore in suspend/resume path
USB: linux-cdc-acm.inf: add support for the acm_ms gadget
EHCI : Fix a regression in the ISO scheduler
xHCI: reset-on-resume quirk for NEC uPD720200
USB: whci-hcd: fix endian conversion in qset_clear()
USB: usb-storage: unusual_devs entry for Kingston DT 101 G2
usb: option: add SIMCom SIM5218
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: comedi: fix integer overflow in do_insnlist_ioctl()
Revert "Staging: comedi: integer overflow in do_insnlist_ioctl()"
Staging: comedi: integer overflow in do_insnlist_ioctl()
Staging: comedi: fix signal handling in read and write
Staging: comedi: fix mmap_count
staging: comedi: fix oops for USB DAQ devices.
staging: comedi: usbduxsigma: Fixed wrong range for the analogue channel.
staging:rts_pstor:Complete scanning_done variable
staging: usbip: bugfix for deadlock
|
|
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix attr2 vs large data fork assert
xfs: force buffer writeback before blocking on the ilock in inode reclaim
xfs: validate acl count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Correct General touch PID
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vmwgfx: integer overflow in vmw_kms_update_layout_ioctl()
drm/radeon/kms: fix 2D tiling CS support on EG/CM
drm/radeon/kms: fix scanout of 2D tiled buffers on EG/CM
drm: Fix lack of CRTC disable for drm_crtc_helper_set_config(.fb=NULL)
drm/radeon/kms: add some new pci ids
drm/radeon/kms: Skip ACPI call to ATIF when possible
drm/radeon/kms: Hide debugging message
drm/radeon/kms: add some loop timeouts in pageflip code
drm/nv50/disp: silence compiler warning
drm/nouveau: fix oopses caused by clear being called on unpopulated ttms
drm/nouveau: Keep RAMIN heap within the channel.
drm/nvd0/disp: fix sor dpms typo, preventing dpms on in some situations
drm/nvc0/gr: fix TP init for transform feedback offset queries
drm/nouveau: add dumb ioctl support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix S3/S4 problem on machines with VREF-pin mute-LED
ALSA: hda_intel - revert a quirk that affect VIA chipsets
ALSA: hda - Avoid touching mute-VREF pin for IDT codecs
firmware: Sigma: Fix endianess issues
firmware: Sigma: Skip header during CRC generation
firmware: Sigma: Prevent out of bounds memory access
ALSA: usb-audio - Support for Roland GAIA SH-01 Synthesizer
ASoC: Supply dcs_codes for newer WM1811 revisions
ASoC: Error out if we can't generate a LRCLK at all for WM8994
ASoC: Correct name of Speyside Main Speaker widget
ASoC: skip resume of soc-audio devices without codecs
ASoC: cs42l51: Fix off-by-one for reg_cache_size
ASoC: drop support for PlayPaq with WM8510
ASoC: mpc8610: tell the CS4270 codec that it's the master
ASoC: cs4720: use snd_soc_cache_sync()
ASoC: SAMSUNG: Fix build error
ASoC: max9877: Update register if either val or val2 is changed
ASoC: Fix wrong define for AD1836_ADC_WORD_OFFSET
|
|
If a device is shutdown, then there might be a pending interrupt,
which will be processed after we reenable interrupts, which causes the
original handler to be run. If the old handler is the (broadcast)
periodic handler the shutdown state might hang the kernel completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
When a better rated broadcast device is installed, then the current
active device is not disabled, which results in two running broadcast
devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
In irq_wait_for_interrupt(), the should_stop member is verified before
setting the task's state to TASK_INTERRUPTIBLE and calling schedule().
In case kthread_stop sets should_stop and wakes up the process after
should_stop is checked by the irq thread but before the task's state
is changed, the irq thread might never exit:
kthread_stop irq_wait_for_interrupt
------------ ----------------------
...
... while (!kthread_should_stop()) {
kthread->should_stop = 1;
wake_up_process(k);
wait_for_completion(&kthread->exited);
...
set_current_state(TASK_INTERRUPTIBLE);
...
schedule();
}
Fix this by checking if the thread should stop after modifying the
task's state.
[ tglx: Simplified it a bit ]
Signed-off-by: Ido Yariv <ido@wizery.com>
Link: http://lkml.kernel.org/r/1322740508-22640-1-git-send-email-ido@wizery.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
|
|
There are two issues in vmw_kms_update_layout_ioctl(). First, the
for loop forgets to index rects and only checks the first element.
Second, there is a potential integer overflow if userspace passes
in a large arg->num_outputs. The call to kzalloc() would allocate
a small buffer, leading to out-of-bounds read.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43191
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43191
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
