diff options
Diffstat (limited to 'drivers/net/hp100.h')
| -rw-r--r-- | drivers/net/hp100.h | 44 |
1 files changed, 22 insertions, 22 deletions
diff --git a/drivers/net/hp100.h b/drivers/net/hp100.h index 236d945987a..e6ca128a556 100644 --- a/drivers/net/hp100.h +++ b/drivers/net/hp100.h @@ -8,9 +8,9 @@ * * This driver is based on the 'hpfepkt' crynwr packet driver. * - * This source/code is public free; you can distribute it and/or modify + * This source/code is public free; you can distribute it and/or modify * it under terms of the GNU General Public License (published by the - * Free Software Foundation) either version two of this License, or any + * Free Software Foundation) either version two of this License, or any * later version. */ @@ -18,7 +18,7 @@ * Hardware Constants ****************************************************************************/ -/* +/* * Page Identifiers * (Swap Paging Register, PAGING, bits 3:0, Offset 0x02) */ @@ -143,15 +143,15 @@ /* ------------------------------------------------------------------------ */ -/* +/* * Hardware ID Register I (Always available, HW_ID, Offset 0x00) */ #define HP100_HW_ID_CASCADE 0x4850 /* Identifies Cascade Chip */ -/* +/* * Hardware ID Register 2 & Paging Register * (Always available, PAGING, Offset 0x02) - * Bits 15:4 are for the Chip ID + * Bits 15:4 are for the Chip ID */ #define HP100_CHIPID_MASK 0xFFF0 #define HP100_CHIPID_SHASTA 0x5350 /* Not 802.12 compliant */ @@ -162,7 +162,7 @@ /* LRF supported */ /* - * Option Registers I and II + * Option Registers I and II * (Always available, OPTION_LSW, Offset 0x04-0x05) */ #define HP100_DEBUG_EN 0x8000 /* 0:Dis., 1:Enable Debug Dump Ptr. */ @@ -187,7 +187,7 @@ /* NIC reset on 0 to 1 transition */ /* - * Option Register III + * Option Register III * (Always available, OPTION_MSW, Offset 0x06) */ #define HP100_PRIORITY_TX 0x0080 /* 1:Do all Tx pkts as priority */ @@ -253,7 +253,7 @@ #define HP100_BM_PCI_8CLK 0x40 /* ... cycles 8 clocks apart */ -/* +/* * Mode Control Register I * (Page HW_MAP, MODECTRL1, Offset0x10) */ @@ -281,7 +281,7 @@ #define HP100_EN_BUS_FAIL 0x80 /* Enables bus-fail portion of misc */ /* interrupt */ -/* +/* * PCI Configuration and Control Register I * (Page HW_MAP, PCICTRL1, Offset 0x12) */ @@ -378,7 +378,7 @@ /* * 100MB LAN Control and Configuration Register - * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a) + * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a) */ #define HP100_VG_SEL 0x80 /* 0:No, 1:Yes use 100 Mbit MAC */ #define HP100_LINK_UP_ST 0x40 /* 0:No, 1:Yes endnode logged in */ @@ -422,7 +422,7 @@ #define HP100_MAC1MODE7 HP100_MAC1MODE6 | HP100_ACC_ERRORED /* - * MAC Configuration Register II + * MAC Configuration Register II * (Page MAC_CTRL, MAC_CFG_2, Offset 0x0d) */ #define HP100_TR_MODE 0x80 /* 0:No, 1:Yes support Token Ring formats */ @@ -447,8 +447,8 @@ #define HP100_MAC2MODE7 KEEP_CRC /* - * MAC Configuration Register III - * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e) + * MAC Configuration Register III + * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e) */ #define HP100_PACKET_PACE 0x03 /* Packet Pacing: * 00: No packet pacing @@ -461,7 +461,7 @@ #define HP100_AUTO_MODE 0x10 /* 1: AutoSelect between 10/100 */ /* - * MAC Configuration Register IV + * MAC Configuration Register IV * (Page MAC_CTRL, MAC_CFG_4, Offset 0x0f) */ #define HP100_MAC_SEL_ST 0x01 /* (R): Status of external VGSEL @@ -469,18 +469,18 @@ #define HP100_LINK_FAIL_ST 0x02 /* (R): Status of Link Fail portion * of the Misc. Interrupt */ -/* - * 100 MB LAN Training Request/Allowed Registers +/* + * 100 MB LAN Training Request/Allowed Registers * (Page MAC_CTRL, TRAIN_REQUEST and TRAIN_ALLOW, Offset 0x14-0x16)(ETR parts only) */ -#define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be +#define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be * a cascaded repeater * 0: ... wants to be a DTE */ #define HP100_MACRQ_PROMSC 0x0006 /* 2 bits: Promiscious mode * 00: Rcv only unicast packets * specifically addr to this * endnode - * 10: Rcv all pckts fwded by + * 10: Rcv all pckts fwded by * the local repeater */ #define HP100_MACRQ_FRAMEFMT_EITHER 0x0018 /* 11: either format allowed */ #define HP100_MACRQ_FRAMEFMT_802_3 0x0000 /* 00: 802.3 is requested */ @@ -492,7 +492,7 @@ * 00: Rcv only unicast packets * specifically addr to this * endnode - * 10: Rcv all pckts fwded by + * 10: Rcv all pckts fwded by * the local repeater */ #define HP100_MALLOW_FRAMEFMT 0x00e0 /* 2 bits: Frame Format * 00: 802.3 format will be used @@ -521,7 +521,7 @@ #define HP100_LAN_COAX 9 /* lan_type value for Coax */ #define HP100_LAN_ERR (-1) /* lan_type value for link down */ -/* +/* * Bus Master Data Structures ---------------------------------------------- */ @@ -554,7 +554,7 @@ typedef struct hp100_ring { #define HP100_PKT_LEN_MASK 0x1FFF /* AND with RxLength to get length */ -/* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED +/* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED bit in the MAC Configuration Register 1 is set. */ #define HP100_RX_PRI 0x8000 /* 0:No, 1:Yes packet is priority */ #define HP100_SDF_ERR 0x4000 /* 0:No, 1:Yes start of frame error */ |