diff options
Diffstat (limited to 'drivers/net/e1000e/ich8lan.c')
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 270 |
1 files changed, 219 insertions, 51 deletions
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 9e23f50fb9c..d56c7473144 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -338,6 +338,7 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) { struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + union ich8_hws_flash_status hsfsts; u32 gfpreg; u32 sector_base_addr; u32 sector_end_addr; @@ -374,6 +375,20 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) /* Adjust to word count */ nvm->flash_bank_size /= sizeof(u16); + /* + * Make sure the flash bank size does not overwrite the 4k + * sector ranges. We may have 64k allotted to us but we only care + * about the first 2 4k sectors. Therefore, if we have anything less + * than 64k set in the HSFSTS register, we will reduce the bank size + * down to 4k and let the rest remain unused. If berasesz == 3, then + * we are working in 64k mode. Otherwise we are not. + */ + if (nvm->flash_bank_size > E1000_ICH8_SHADOW_RAM_WORDS) { + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.berasesz != 3) + nvm->flash_bank_size = E1000_ICH8_SHADOW_RAM_WORDS; + } + nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS; /* Clear shadow ram */ @@ -446,6 +461,95 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter) return 0; } +/** + * e1000_check_for_copper_link_ich8lan - Check for link (Copper) + * @hw: pointer to the HW structure + * + * Checks to see of the link status of the hardware has changed. If a + * change in link status has been detected, then we read the PHY registers + * to get the current speed/duplex if link exists. + **/ +static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + bool link; + + /* + * We only want to go out to the PHY registers to see if Auto-Neg + * has completed and/or if our link status has changed. The + * get_link_status flag is set upon receiving a Link Status + * Change or Rx Sequence Error interrupt. + */ + if (!mac->get_link_status) { + ret_val = 0; + goto out; + } + + if (hw->mac.type == e1000_pchlan) { + ret_val = e1000e_write_kmrn_reg(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + E1000_KMRNCTRLSTA_K1_ENABLE); + if (ret_val) + goto out; + } + + /* + * First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + */ + ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) + goto out; /* No link detected */ + + mac->get_link_status = false; + + if (hw->phy.type == e1000_phy_82578) { + ret_val = e1000_link_stall_workaround_hv(hw); + if (ret_val) + goto out; + } + + /* + * Check if there was DownShift, must be checked + * immediately after link-up + */ + e1000e_check_downshift(hw); + + /* + * If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) { + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + /* + * Auto-Neg is enabled. Auto Speed Detection takes care + * of MAC speed/duplex configuration. So we only need to + * configure Collision Distance in the MAC. + */ + e1000e_config_collision_dist(hw); + + /* + * Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = e1000e_config_fc_after_link_up(hw); + if (ret_val) + hw_dbg(hw, "Error configuring flow control\n"); + +out: + return ret_val; +} + static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; @@ -694,6 +798,38 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw) } /** + * e1000_lan_init_done_ich8lan - Check for PHY config completion + * @hw: pointer to the HW structure + * + * Check the appropriate indication the MAC has finished configuring the + * PHY after a software reset. + **/ +static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw) +{ + u32 data, loop = E1000_ICH8_LAN_INIT_TIMEOUT; + + /* Wait for basic configuration completes before proceeding */ + do { + data = er32(STATUS); + data &= E1000_STATUS_LAN_INIT_DONE; + udelay(100); + } while ((!data) && --loop); + + /* + * If basic configuration is incomplete before the above loop + * count reaches 0, loading the configuration from NVM will + * leave the PHY in a bad state possibly resulting in no link. + */ + if (loop == 0) + hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); + + /* Clear the Init Done bit for the next init event */ + data = er32(STATUS); + data &= ~E1000_STATUS_LAN_INIT_DONE; + ew32(STATUS, data); +} + +/** * e1000_phy_hw_reset_ich8lan - Performs a PHY reset * @hw: pointer to the HW structure * @@ -707,13 +843,15 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) u32 i; u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; s32 ret_val; - u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT; u16 word_addr, reg_data, reg_addr, phy_page = 0; ret_val = e1000e_phy_hw_reset_generic(hw); if (ret_val) return ret_val; + /* Allow time for h/w to get to a quiescent state after reset */ + mdelay(10); + if (hw->mac.type == e1000_pchlan) { ret_val = e1000_hv_phy_workarounds_ich8lan(hw); if (ret_val) @@ -741,26 +879,8 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) if (!(data & sw_cfg_mask)) return 0; - /* Wait for basic configuration completes before proceeding*/ - do { - data = er32(STATUS); - data &= E1000_STATUS_LAN_INIT_DONE; - udelay(100); - } while ((!data) && --loop); - - /* - * If basic configuration is incomplete before the above loop - * count reaches 0, loading the configuration from NVM will - * leave the PHY in a bad state possibly resulting in no link. - */ - if (loop == 0) { - hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); - } - - /* Clear the Init Done bit for the next init event */ - data = er32(STATUS); - data &= ~E1000_STATUS_LAN_INIT_DONE; - ew32(STATUS, data); + /* Wait for basic configuration completes before proceeding */ + e1000_lan_init_done_ich8lan(hw); /* * Make sure HW does not configure LCD from PHY @@ -961,12 +1081,14 @@ static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; ew32(PHY_CTRL, phy_ctrl); + if (phy->type != e1000_phy_igp_3) + return 0; + /* * Call gig speed drop workaround on LPLU before accessing * any PHY registers */ - if ((hw->mac.type == e1000_ich8lan) && - (hw->phy.type == e1000_phy_igp_3)) + if (hw->mac.type == e1000_ich8lan) e1000e_gig_downshift_workaround_ich8lan(hw); /* When LPLU is enabled, we should disable SmartSpeed */ @@ -979,6 +1101,9 @@ static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; ew32(PHY_CTRL, phy_ctrl); + if (phy->type != e1000_phy_igp_3) + return 0; + /* * LPLU and SmartSpeed are mutually exclusive. LPLU is used * during Dx states where the power conservation is most @@ -1038,6 +1163,10 @@ static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) if (!active) { phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; ew32(PHY_CTRL, phy_ctrl); + + if (phy->type != e1000_phy_igp_3) + return 0; + /* * LPLU and SmartSpeed are mutually exclusive. LPLU is used * during Dx states where the power conservation is most @@ -1073,12 +1202,14 @@ static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; ew32(PHY_CTRL, phy_ctrl); + if (phy->type != e1000_phy_igp_3) + return 0; + /* * Call gig speed drop workaround on LPLU before accessing * any PHY registers */ - if ((hw->mac.type == e1000_ich8lan) && - (hw->phy.type == e1000_phy_igp_3)) + if (hw->mac.type == e1000_ich8lan) e1000e_gig_downshift_workaround_ich8lan(hw); /* When LPLU is enabled, we should disable SmartSpeed */ @@ -1905,7 +2036,7 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) break; case 1: sector_size = ICH_FLASH_SEG_SIZE_4K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_4K; + iteration = 1; break; case 2: if (hw->mac.type == e1000_ich9lan) { @@ -1917,7 +2048,7 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) break; case 3: sector_size = ICH_FLASH_SEG_SIZE_64K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_64K; + iteration = 1; break; default: return -E1000_ERR_NVM; @@ -2143,6 +2274,12 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ctrl = er32(CTRL); if (!e1000_check_reset_block(hw)) { + /* Clear PHY Reset Asserted bit */ + if (hw->mac.type >= e1000_pchlan) { + u32 status = er32(STATUS); + ew32(STATUS, status & ~E1000_STATUS_PHYRA); + } + /* * PHY HW reset requires MAC CORE reset at the same * time to make sure the interface between MAC and the @@ -2156,23 +2293,34 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ew32(CTRL, (ctrl | E1000_CTRL_RST)); msleep(20); - if (!ret_val) { - /* release the swflag because it is not reset by - * hardware reset - */ + if (!ret_val) e1000_release_swflag_ich8lan(hw); - } - ret_val = e1000e_get_auto_rd_done(hw); - if (ret_val) { - /* - * When auto config read does not complete, do not - * return with an error. This can happen in situations - * where there is no eeprom and prevents getting link. - */ - hw_dbg(hw, "Auto Read Done did not complete\n"); + if (ctrl & E1000_CTRL_PHY_RST) + ret_val = hw->phy.ops.get_cfg_done(hw); + + if (hw->mac.type >= e1000_ich10lan) { + e1000_lan_init_done_ich8lan(hw); + } else { + ret_val = e1000e_get_auto_rd_done(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + hw_dbg(hw, "Auto Read Done did not complete\n"); + } } + /* + * For PCH, this write will make sure that any noise + * will be detected as a CRC error and be dropped rather than show up + * as a bad packet to the DMA engine. + */ + if (hw->mac.type == e1000_pchlan) + ew32(CRC_OFFSET, 0x65656565); + ew32(IMC, 0xffffffff); icr = er32(ICR); @@ -2222,6 +2370,18 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) for (i = 0; i < mac->mta_reg_count; i++) E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + /* + * The 82578 Rx buffer will stall if wakeup is enabled in host and + * the ME. Reading the BM_WUC register will clear the host wakeup bit. + * Reset the phy after disabling host wakeup to reset the Rx buffer. + */ + if (hw->phy.type == e1000_phy_82578) { + hw->phy.ops.read_phy_reg(hw, BM_WUC, &i); + ret_val = e1000_phy_hw_reset_ich8lan(hw); + if (ret_val) + return ret_val; + } + /* Setup link and flow control */ ret_val = e1000_setup_link_ich8lan(hw); @@ -2254,16 +2414,6 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) ew32(CTRL_EXT, ctrl_ext); /* - * The 82578 Rx buffer will stall if wakeup is enabled in host and - * the ME. Reading the BM_WUC register will clear the host wakeup bit. - * Reset the phy after disabling host wakeup to reset the Rx buffer. - */ - if (hw->phy.type == e1000_phy_82578) { - e1e_rphy(hw, BM_WUC, &i); - e1000e_phy_hw_reset_generic(hw); - } - - /* * Clear all of the statistics registers (clear on read). It is * important that we do this after we have tried to establish link * because the symbol error count will increment wildly if there @@ -2485,6 +2635,14 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, if (ret_val) return ret_val; + if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) { + ret_val = e1000e_write_kmrn_reg(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + E1000_KMRNCTRLSTA_K1_DISABLE); + if (ret_val) + return ret_val; + } + if ((hw->mac.type == e1000_ich8lan) && (hw->phy.type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { @@ -2850,6 +3008,16 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw) { u32 bank = 0; + if (hw->mac.type >= e1000_pchlan) { + u32 status = er32(STATUS); + + if (status & E1000_STATUS_PHYRA) + ew32(STATUS, status & ~E1000_STATUS_PHYRA); + else + hw_dbg(hw, + "PHY Reset Asserted not set - needs delay\n"); + } + e1000e_get_cfg_done(hw); /* If EEPROM is not marked present, init the IGP 3 PHY manually */ @@ -2921,7 +3089,7 @@ static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) static struct e1000_mac_operations ich8_mac_ops = { .id_led_init = e1000e_id_led_init, .check_mng_mode = e1000_check_mng_mode_ich8lan, - .check_for_link = e1000e_check_for_copper_link, + .check_for_link = e1000_check_for_copper_link_ich8lan, /* cleanup_led dependent on mac type */ .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan, .get_bus_info = e1000_get_bus_info_ich8lan, |