1 files changed, 0 insertions, 52 deletions
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index 92fc3b88a60..7782e0f88a3 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -47,58 +47,6 @@ void __iomem *prcm_mpu_base;
 
 #define MAX_MODULE_ENABLE_WAIT		100000
 
-/* Resets clock rates and reboots the system. Only called from system.h */
-void omap_prcm_restart(char mode, const char *cmd)
-{
-	s16 prcm_offs = 0;
-
-	if (cpu_is_omap24xx()) {
-		omap2xxx_clk_prepare_for_reboot();
-
-		prcm_offs = WKUP_MOD;
-	} else if (cpu_is_omap34xx()) {
-		prcm_offs = OMAP3430_GR_MOD;
-		omap3_ctrl_write_boot_mode((cmd ? (u8)*cmd : 0));
-	} else if (cpu_is_omap44xx()) {
-		omap4_prminst_global_warm_sw_reset(); /* never returns */
-	} else {
-		WARN_ON(1);
-	}
-
-	/*
-	 * As per Errata i520, in some cases, user will not be able to
-	 * access DDR memory after warm-reset.
-	 * This situation occurs while the warm-reset happens during a read
-	 * access to DDR memory. In that particular condition, DDR memory
-	 * does not respond to a corrupted read command due to the warm
-	 * reset occurrence but SDRC is waiting for read completion.
-	 * SDRC is not sensitive to the warm reset, but the interconnect is
-	 * reset on the fly, thus causing a misalignment between SDRC logic,
-	 * interconnect logic and DDR memory state.
-	 * WORKAROUND:
-	 * Steps to perform before a Warm reset is trigged:
-	 * 1. enable self-refresh on idle request
-	 * 2. put SDRC in idle
-	 * 3. wait until SDRC goes to idle
-	 * 4. generate SW reset (Global SW reset)
-	 *
-	 * Steps to be performed after warm reset occurs (in bootloader):
-	 * if HW warm reset is the source, apply below steps before any
-	 * accesses to SDRAM:
-	 * 1. Reset SMS and SDRC and wait till reset is complete
-	 * 2. Re-initialize SMS, SDRC and memory
-	 *
-	 * NOTE: Above work around is required only if arch reset is implemented
-	 * using Global SW reset(GLOBAL_SW_RST). DPLL3 reset does not need
-	 * the WA since it resets SDRC as well as part of cold reset.
-	 */
-
-	/* XXX should be moved to some OMAP2/3 specific code */
-	omap2_prm_set_mod_reg_bits(OMAP_RST_DPLL3_MASK, prcm_offs,
-				   OMAP2_RM_RSTCTRL);
-	omap2_prm_read_mod_reg(prcm_offs, OMAP2_RM_RSTCTRL); /* OCP barrier */
-}
-
 /**
  * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
  * @reg: physical address of module IDLEST register