diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/DocBook/filesystems.tmpl | 5 | ||||
| -rw-r--r-- | Documentation/arm/SH-Mobile/Makefile | 8 | ||||
| -rw-r--r-- | Documentation/arm/SH-Mobile/vrl4.c | 169 | ||||
| -rw-r--r-- | Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt | 29 | ||||
| -rw-r--r-- | Documentation/hwmon/jc42 | 21 | ||||
| -rw-r--r-- | Documentation/hwmon/k10temp | 8 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 24 | ||||
| -rw-r--r-- | Documentation/networking/00-INDEX | 6 | ||||
| -rw-r--r-- | Documentation/networking/Makefile | 2 | ||||
| -rw-r--r-- | Documentation/networking/dns_resolver.txt | 9 | ||||
| -rw-r--r-- | Documentation/workqueue.txt | 4 |
11 files changed, 261 insertions, 24 deletions
diff --git a/Documentation/DocBook/filesystems.tmpl b/Documentation/DocBook/filesystems.tmpl index 5e87ad58c0b..f51f28531b8 100644 --- a/Documentation/DocBook/filesystems.tmpl +++ b/Documentation/DocBook/filesystems.tmpl @@ -82,6 +82,11 @@ </sect1> </chapter> + <chapter id="fs_events"> + <title>Events based on file descriptors</title> +!Efs/eventfd.c + </chapter> + <chapter id="sysfs"> <title>The Filesystem for Exporting Kernel Objects</title> !Efs/sysfs/file.c diff --git a/Documentation/arm/SH-Mobile/Makefile b/Documentation/arm/SH-Mobile/Makefile new file mode 100644 index 00000000000..8771d832cf8 --- /dev/null +++ b/Documentation/arm/SH-Mobile/Makefile @@ -0,0 +1,8 @@ +BIN := vrl4 + +.PHONY: all +all: $(BIN) + +.PHONY: clean +clean: + rm -f *.o $(BIN) diff --git a/Documentation/arm/SH-Mobile/vrl4.c b/Documentation/arm/SH-Mobile/vrl4.c new file mode 100644 index 00000000000..e8a191358ad --- /dev/null +++ b/Documentation/arm/SH-Mobile/vrl4.c @@ -0,0 +1,169 @@ +/* + * vrl4 format generator + * + * Copyright (C) 2010 Simon Horman + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ + +/* + * usage: vrl4 < zImage > out + * dd if=out of=/dev/sdx bs=512 seek=1 # Write the image to sector 1 + * + * Reads a zImage from stdin and writes a vrl4 image to stdout. + * In practice this means writing a padded vrl4 header to stdout followed + * by the zImage. + * + * The padding places the zImage at ALIGN bytes into the output. + * The vrl4 uses ALIGN + START_BASE as the start_address. + * This is where the mask ROM will jump to after verifying the header. + * + * The header sets copy_size to min(sizeof(zImage), MAX_BOOT_PROG_LEN) + ALIGN. + * That is, the mask ROM will load the padded header (ALIGN bytes) + * And then MAX_BOOT_PROG_LEN bytes of the image, or the entire image, + * whichever is smaller. + * + * The zImage is not modified in any way. + */ + +#define _BSD_SOURCE +#include <endian.h> +#include <unistd.h> +#include <stdint.h> +#include <stdio.h> +#include <errno.h> + +struct hdr { + uint32_t magic1; + uint32_t reserved1; + uint32_t magic2; + uint32_t reserved2; + uint16_t copy_size; + uint16_t boot_options; + uint32_t reserved3; + uint32_t start_address; + uint32_t reserved4; + uint32_t reserved5; + char reserved6[308]; +}; + +#define DECLARE_HDR(h) \ + struct hdr (h) = { \ + .magic1 = htole32(0xea000000), \ + .reserved1 = htole32(0x56), \ + .magic2 = htole32(0xe59ff008), \ + .reserved3 = htole16(0x1) } + +/* Align to 512 bytes, the MMCIF sector size */ +#define ALIGN_BITS 9 +#define ALIGN (1 << ALIGN_BITS) + +#define START_BASE 0xe55b0000 + +/* + * With an alignment of 512 the header uses the first sector. + * There is a 128 sector (64kbyte) limit on the data loaded by the mask ROM. + * So there are 127 sectors left for the boot programme. But in practice + * Only a small portion of a zImage is needed, 16 sectors should be more + * than enough. + * + * Note that this sets how much of the zImage is copied by the mask ROM. + * The entire zImage is present after the header and is loaded + * by the code in the boot program (which is the first portion of the zImage). + */ +#define MAX_BOOT_PROG_LEN (16 * 512) + +#define ROUND_UP(x) ((x + ALIGN - 1) & ~(ALIGN - 1)) + +ssize_t do_read(int fd, void *buf, size_t count) +{ + size_t offset = 0; + ssize_t l; + + while (offset < count) { + l = read(fd, buf + offset, count - offset); + if (!l) + break; + if (l < 0) { + if (errno == EAGAIN || errno == EWOULDBLOCK) + continue; + perror("read"); + return -1; + } + offset += l; + } + + return offset; +} + +ssize_t do_write(int fd, const void *buf, size_t count) +{ + size_t offset = 0; + ssize_t l; + + while (offset < count) { + l = write(fd, buf + offset, count - offset); + if (l < 0) { + if (errno == EAGAIN || errno == EWOULDBLOCK) + continue; + perror("write"); + return -1; + } + offset += l; + } + + return offset; +} + +ssize_t write_zero(int fd, size_t len) +{ + size_t i = len; + + while (i--) { + const char x = 0; + if (do_write(fd, &x, 1) < 0) + return -1; + } + + return len; +} + +int main(void) +{ + DECLARE_HDR(hdr); + char boot_program[MAX_BOOT_PROG_LEN]; + size_t aligned_hdr_len, alligned_prog_len; + ssize_t prog_len; + + prog_len = do_read(0, boot_program, sizeof(boot_program)); + if (prog_len <= 0) + return -1; + + aligned_hdr_len = ROUND_UP(sizeof(hdr)); + hdr.start_address = htole32(START_BASE + aligned_hdr_len); + alligned_prog_len = ROUND_UP(prog_len); + hdr.copy_size = htole16(aligned_hdr_len + alligned_prog_len); + + if (do_write(1, &hdr, sizeof(hdr)) < 0) + return -1; + if (write_zero(1, aligned_hdr_len - sizeof(hdr)) < 0) + return -1; + + if (do_write(1, boot_program, prog_len) < 0) + return 1; + + /* Write out the rest of the kernel */ + while (1) { + prog_len = do_read(0, boot_program, sizeof(boot_program)); + if (prog_len < 0) + return 1; + if (prog_len == 0) + break; + if (do_write(1, boot_program, prog_len) < 0) + return 1; + } + + return 0; +} diff --git a/Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt b/Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt new file mode 100644 index 00000000000..efff8ae2713 --- /dev/null +++ b/Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt @@ -0,0 +1,29 @@ +ROM-able zImage boot from MMC +----------------------------- + +An ROM-able zImage compiled with ZBOOT_ROM_MMCIF may be written to MMC and +SuperH Mobile ARM will to boot directly from the MMCIF hardware block. + +This is achieved by the mask ROM loading the first portion of the image into +MERAM and then jumping to it. This portion contains loader code which +copies the entire image to SDRAM and jumps to it. From there the zImage +boot code proceeds as normal, uncompressing the image into its final +location and then jumping to it. + +This code has been tested on an AP4EB board using the developer 1A eMMC +boot mode which is configured using the following jumper settings. +The board used for testing required a patched mask ROM in order for +this mode to function. + + 8 7 6 5 4 3 2 1 + x|x|x|x|x| |x| +S4 -+-+-+-+-+-+-+- + | | | | |x| |x on + +The zImage must be written to the MMC card at sector 1 (512 bytes) in +vrl4 format. A utility vrl4 is supplied to accomplish this. + +e.g. + vrl4 < zImage | dd of=/dev/sdX bs=512 seek=1 + +A dual-voltage MMC 4.0 card was used for testing. diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 index 0e76ef12e4c..a22ecf48f25 100644 --- a/Documentation/hwmon/jc42 +++ b/Documentation/hwmon/jc42 @@ -51,7 +51,8 @@ Supported chips: * JEDEC JC 42.4 compliant temperature sensor chips Prefix: 'jc42' Addresses scanned: I2C 0x18 - 0x1f - Datasheet: - + Datasheet: + http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf Author: Guenter Roeck <guenter.roeck@ericsson.com> @@ -60,7 +61,11 @@ Author: Description ----------- -This driver implements support for JEDEC JC 42.4 compliant temperature sensors. +This driver implements support for JEDEC JC 42.4 compliant temperature sensors, +which are used on many DDR3 memory modules for mobile devices and servers. Some +systems use the sensor to prevent memory overheating by automatically throttling +the memory controller. + The driver auto-detects the chips listed above, but can be manually instantiated to support other JC 42.4 compliant chips. @@ -81,15 +86,19 @@ limits. The chip supports only a single register to configure the hysteresis, which applies to all limits. This register can be written by writing into temp1_crit_hyst. Other hysteresis attributes are read-only. +If the BIOS has configured the sensor for automatic temperature management, it +is likely that it has locked the registers, i.e., that the temperature limits +cannot be changed. + Sysfs entries ------------- temp1_input Temperature (RO) -temp1_min Minimum temperature (RW) -temp1_max Maximum temperature (RW) -temp1_crit Critical high temperature (RW) +temp1_min Minimum temperature (RO or RW) +temp1_max Maximum temperature (RO or RW) +temp1_crit Critical high temperature (RO or RW) -temp1_crit_hyst Critical hysteresis temperature (RW) +temp1_crit_hyst Critical hysteresis temperature (RO or RW) temp1_max_hyst Maximum hysteresis temperature (RO) temp1_min_alarm Temperature low alarm diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp index 6526eee525a..d2b56a4fd1f 100644 --- a/Documentation/hwmon/k10temp +++ b/Documentation/hwmon/k10temp @@ -9,6 +9,8 @@ Supported chips: Socket S1G3: Athlon II, Sempron, Turion II * AMD Family 11h processors: Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra) +* AMD Family 12h processors: "Llano" +* AMD Family 14h processors: "Brazos" (C/E/G-Series) Prefix: 'k10temp' Addresses scanned: PCI space @@ -17,10 +19,14 @@ Supported chips: http://support.amd.com/us/Processor_TechDocs/31116.pdf BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors: http://support.amd.com/us/Processor_TechDocs/41256.pdf + BIOS and Kernel Developer's Guide (BKDG) for AMD Family 14h Models 00h-0Fh Processors: + http://support.amd.com/us/Processor_TechDocs/43170.pdf Revision Guide for AMD Family 10h Processors: http://support.amd.com/us/Processor_TechDocs/41322.pdf Revision Guide for AMD Family 11h Processors: http://support.amd.com/us/Processor_TechDocs/41788.pdf + Revision Guide for AMD Family 14h Models 00h-0Fh Processors: + http://support.amd.com/us/Processor_TechDocs/47534.pdf AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks: http://support.amd.com/us/Processor_TechDocs/43373.pdf AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet: @@ -34,7 +40,7 @@ Description ----------- This driver permits reading of the internal temperature sensor of AMD -Family 10h and 11h processors. +Family 10h/11h/12h/14h processors. All these processors have a sensor, but on those for Socket F or AM2+, the sensor may return inconsistent values (erratum 319). The driver diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 89835a4766a..f4a04c0c7ed 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -144,6 +144,11 @@ a fixed number of characters. This limit depends on the architecture and is between 256 and 4096 characters. It is defined in the file ./include/asm/setup.h as COMMAND_LINE_SIZE. +Finally, the [KMG] suffix is commonly described after a number of kernel +parameter values. These 'K', 'M', and 'G' letters represent the _binary_ +multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30 +bytes respectively. Such letter suffixes can also be entirely omitted. + acpi= [HW,ACPI,X86] Advanced Configuration and Power Interface @@ -545,16 +550,20 @@ and is between 256 and 4096 characters. It is defined in the file Format: <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>] - crashkernel=nn[KMG]@ss[KMG] - [KNL] Reserve a chunk of physical memory to - hold a kernel to switch to with kexec on panic. + crashkernel=size[KMG][@offset[KMG]] + [KNL] Using kexec, Linux can switch to a 'crash kernel' + upon panic. This parameter reserves the physical + memory region [offset, offset + size] for that kernel + image. If '@offset' is omitted, then a suitable offset + is selected automatically. Check + Documentation/kdump/kdump.txt for further details. crashkernel=range1:size1[,range2:size2,...][@offset] [KNL] Same as above, but depends on the memory in the running system. The syntax of range is start-[end] where start and end are both a memory unit (amount[KMG]). See also - Documentation/kdump/kdump.txt for a example. + Documentation/kdump/kdump.txt for an example. cs89x0_dma= [HW,NET] Format: <dma> @@ -1262,10 +1271,9 @@ and is between 256 and 4096 characters. It is defined in the file 6 (KERN_INFO) informational 7 (KERN_DEBUG) debug-level messages - log_buf_len=n Sets the size of the printk ring buffer, in bytes. - Format: { n | nk | nM } - n must be a power of two. The default size - is set in the kernel config file. + log_buf_len=n[KMG] Sets the size of the printk ring buffer, + in bytes. n must be a power of two. The default + size is set in the kernel config file. logo.nologo [FB] Disables display of the built-in Linux logo. This may be used to provide more screen space for diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX index fe5c099b8fc..4edd78dfb36 100644 --- a/Documentation/networking/00-INDEX +++ b/Documentation/networking/00-INDEX @@ -40,8 +40,6 @@ decnet.txt - info on using the DECnet networking layer in Linux. depca.txt - the Digital DEPCA/EtherWORKS DE1?? and DE2?? LANCE Ethernet driver -dgrs.txt - - the Digi International RightSwitch SE-X Ethernet driver dmfe.txt - info on the Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver. e100.txt @@ -50,8 +48,6 @@ e1000.txt - info on Intel's E1000 line of gigabit ethernet boards eql.txt - serial IP load balancing -ethertap.txt - - the Ethertap user space packet reception and transmission driver ewrk3.txt - the Digital EtherWORKS 3 DE203/4/5 Ethernet driver filter.txt @@ -104,8 +100,6 @@ tuntap.txt - TUN/TAP device driver, allowing user space Rx/Tx of packets. vortex.txt - info on using 3Com Vortex (3c590, 3c592, 3c595, 3c597) Ethernet cards. -wavelan.txt - - AT&T GIS (nee NCR) WaveLAN card: An Ethernet-like radio transceiver x25.txt - general info on X.25 development. x25-iface.txt diff --git a/Documentation/networking/Makefile b/Documentation/networking/Makefile index 5aba7a33aee..24c308dd3fd 100644 --- a/Documentation/networking/Makefile +++ b/Documentation/networking/Makefile @@ -4,6 +4,8 @@ obj- := dummy.o # List of programs to build hostprogs-y := ifenslave +HOSTCFLAGS_ifenslave.o += -I$(objtree)/usr/include + # Tell kbuild to always build the programs always := $(hostprogs-y) diff --git a/Documentation/networking/dns_resolver.txt b/Documentation/networking/dns_resolver.txt index aefd1e68180..04ca06325b0 100644 --- a/Documentation/networking/dns_resolver.txt +++ b/Documentation/networking/dns_resolver.txt @@ -61,7 +61,6 @@ before the more general line given above as the first match is the one taken. create dns_resolver foo:* * /usr/sbin/dns.foo %k - ===== USAGE ===== @@ -104,6 +103,14 @@ implemented in the module can be called after doing: returned also. +=============================== +READING DNS KEYS FROM USERSPACE +=============================== + +Keys of dns_resolver type can be read from userspace using keyctl_read() or +"keyctl read/print/pipe". + + ========= MECHANISM ========= diff --git a/Documentation/workqueue.txt b/Documentation/workqueue.txt index 996a27d9b8d..01c513fac40 100644 --- a/Documentation/workqueue.txt +++ b/Documentation/workqueue.txt @@ -190,9 +190,9 @@ resources, scheduled and executed. * Long running CPU intensive workloads which can be better managed by the system scheduler. - WQ_FREEZEABLE + WQ_FREEZABLE - A freezeable wq participates in the freeze phase of the system + A freezable wq participates in the freeze phase of the system suspend operations. Work items on the wq are drained and no new work item starts execution until thawed. |