diff options
Diffstat (limited to 'Documentation/powerpc/dts-bindings')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt | 93 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/board.txt | 4 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/can.txt | 53 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt | 54 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/dma.txt | 8 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/i2c.txt | 30 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt | 70 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/mpc5200.txt | 20 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/mpic.txt | 42 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/spi.txt | 7 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/nintendo/gamecube.txt | 109 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/nintendo/wii.txt | 184 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/xilinx.txt | 11 |
13 files changed, 676 insertions, 9 deletions
diff --git a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt new file mode 100644 index 00000000000..515ebcf1b97 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt @@ -0,0 +1,93 @@ +PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) + +Device nodes needed for operation of the ppc440spe-adma driver +are specified hereby. These are I2O/DMA, DMA and XOR nodes +for DMA engines and Memory Queue Module node. The latter is used +by ADMA driver for configuration of RAID-6 H/W capabilities of +the PPC440SPe. In addition to the nodes and properties described +below, the ranges property of PLB node must specify ranges for +DMA devices. + + i) The I2O node + + Required properties: + + - compatible : "ibm,i2o-440spe"; + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + + Example: + + I2O: i2o@400100000 { + compatible = "ibm,i2o-440spe"; + reg = <0x00000004 0x00100000 0x100>; + dcr-reg = <0x060 0x020>; + }; + + + ii) The DMA node + + Required properties: + + - compatible : "ibm,dma-440spe"; + - cell-index : 1 cell, hardware index of the DMA engine + (typically 0x0 and 0x1 for DMA0 and DMA1) + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + - interrupts : <interrupt mapping for DMA0/1 interrupts sources: + 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) + and DMA Error IRQ (on UIC1). The latter is common + for both DMA engines>. + - interrupt-parent : needed for interrupt mapping + + Example: + + DMA0: dma0@400100100 { + compatible = "ibm,dma-440spe"; + cell-index = <0>; + reg = <0x00000004 0x00100100 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA0>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x14 4 + 1 &UIC1 0x16 4>; + }; + + + iii) XOR Accelerator node + + Required properties: + + - compatible : "amcc,xor-accelerator"; + - reg : <registers mapping> + - interrupts : <interrupt mapping for XOR interrupt source> + - interrupt-parent : for interrupt mapping + + Example: + + xor-accel@400200000 { + compatible = "amcc,xor-accelerator"; + reg = <0x00000004 0x00200000 0x400>; + interrupt-parent = <&UIC1>; + interrupts = <0x1f 4>; + }; + + + iv) Memory Queue Module node + + Required properties: + + - compatible : "ibm,mq-440spe"; + - dcr-reg : <DCR registers range> + + Example: + + MQ0: mq { + compatible = "ibm,mq-440spe"; + dcr-reg = <0x040 0x020>; + }; + diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt index e8b5bc24d0a..39e941515a3 100644 --- a/Documentation/powerpc/dts-bindings/fsl/board.txt +++ b/Documentation/powerpc/dts-bindings/fsl/board.txt @@ -20,12 +20,16 @@ Required properities: - compatible : should be "fsl,fpga-pixis". - reg : should contain the address and the length of the FPPGA register set. +- interrupt-parent: should specify phandle for the interrupt controller. +- interrupts : should specify event (wakeup) IRQ. Example (MPC8610HPCD): board-control@e8000000 { compatible = "fsl,fpga-pixis"; reg = <0xe8000000 32>; + interrupt-parent = <&mpic>; + interrupts = <8 8>; }; * Freescale BCSR GPIO banks diff --git a/Documentation/powerpc/dts-bindings/fsl/can.txt b/Documentation/powerpc/dts-bindings/fsl/can.txt new file mode 100644 index 00000000000..2fa4fcd38fd --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/can.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt index 6e37be1eeb2..4f8930263dd 100644 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt @@ -21,6 +21,15 @@ Required properties: - fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the threads. +Optional properties: +- fsl,firmware-phandle: + Usage: required only if there is no fsl,qe-firmware child node + Value type: <phandle> + Definition: Points to a firmware node (see "QE Firmware Node" below) + that contains the firmware that should be uploaded for this QE. + The compatible property for the firmware node should say, + "fsl,qe-firmware". + Recommended properties - brg-frequency : the internal clock source frequency for baud-rate generators in Hz. @@ -59,3 +68,48 @@ Example: reg = <0 c000>; }; }; + +* QE Firmware Node + +This node defines a firmware binary that is embedded in the device tree, for +the purpose of passing the firmware from bootloader to the kernel, or from +the hypervisor to the guest. + +The firmware node itself contains the firmware binary contents, a compatible +property, and any firmware-specific properties. The node should be placed +inside a QE node that needs it. Doing so eliminates the need for a +fsl,firmware-phandle property. Other QE nodes that need the same firmware +should define an fsl,firmware-phandle property that points to the firmware node +in the first QE node. + +The fsl,firmware property can be specified in the DTS (possibly using incbin) +or can be inserted by the boot loader at boot time. + +Required properties: + - compatible + Usage: required + Value type: <string> + Definition: A standard property. Specify a string that indicates what + kind of firmware it is. For QE, this should be "fsl,qe-firmware". + + - fsl,firmware + Usage: required + Value type: <prop-encoded-array>, encoded as an array of bytes + Definition: A standard property. This property contains the firmware + binary "blob". + +Example: + qe1@e0080000 { + compatible = "fsl,qe"; + qe_firmware:qe-firmware { + compatible = "fsl,qe-firmware"; + fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; + }; + ... + }; + + qe2@e0090000 { + compatible = "fsl,qe"; + fsl,firmware-phandle = <&qe_firmware>; + ... + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt index 0732cdd05ba..2a4b4bce611 100644 --- a/Documentation/powerpc/dts-bindings/fsl/dma.txt +++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt @@ -44,21 +44,29 @@ Example: compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <0>; reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <1>; reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <2>; reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <3>; reg = <0x180 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; }; diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt index b6d2e21474f..50da2031058 100644 --- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt +++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt @@ -2,15 +2,14 @@ Required properties : - - device_type : Should be "i2c" - reg : Offset and length of the register set for the device + - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a + compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, + mpc5200 or mpc5200b. For the mpc5121, an additional node + "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. Recommended properties : - - compatible : compatibility list with 2 entries, the first should - be "fsl,CHIP-i2c" where CHIP is the name of a compatible processor, - e.g. mpc8313, mpc8543, mpc8544, mpc5200 or mpc5200b. The second one - should be "fsl-i2c". - interrupts : <a b> where a is the interrupt number and b is a field that represents an encoding of the sense and level information for the interrupt. This should be encoded based on @@ -24,25 +23,40 @@ Recommended properties : Examples : + /* MPC5121 based board */ + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c", "fsl-i2c"; + reg = <0x1740 0x20>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + /* MPC5200B based board */ i2c@3d00 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - cell-index = <0>; reg = <0x3d00 0x40>; interrupts = <2 15 0>; interrupt-parent = <&mpc5200_pic>; fsl,preserve-clocking; }; + /* MPC8544 base board */ i2c@3100 { #address-cells = <1>; #size-cells = <0>; - cell-index = <1>; compatible = "fsl,mpc8544-i2c", "fsl-i2c"; reg = <0x3100 0x100>; interrupts = <43 2>; interrupt-parent = <&mpic>; clock-frequency = <400000>; }; - diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt new file mode 100644 index 00000000000..8832e879891 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt @@ -0,0 +1,70 @@ +MPC5121 PSC Device Tree Bindings + +PSC in UART mode +---------------- + +For PSC in UART mode the needed PSC serial devices +are specified by fsl,mpc5121-psc-uart nodes in the +fsl,mpc5121-immr SoC node. Additionally the PSC FIFO +Controller node fsl,mpc5121-psc-fifo is requered there: + +fsl,mpc5121-psc-uart nodes +-------------------------- + +Required properties : + - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" + - cell-index : Index of the PSC in hardware + - reg : Offset and length of the register set for the PSC device + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Recommended properties : + - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) + - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) + + +fsl,mpc5121-psc-fifo node +------------------------- + +Required properties : + - compatible : Should be "fsl,mpc5121-psc-fifo" + - reg : Offset and length of the register set for the PSC + FIFO Controller + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + +Example for a board using PSC0 and PSC1 devices in serial mode: + +serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; +}; diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt index 8447fd7090d..4ccb2cd5df9 100644 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt +++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt @@ -103,7 +103,22 @@ fsl,mpc5200-gpt nodes --------------------- On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board design supports the internal wdt, then the device node for GPT0 should -include the empty property 'fsl,has-wdt'. +include the empty property 'fsl,has-wdt'. Note that this does not activate +the watchdog. The timer will function as a GPT if the timer api is used, and +it will function as watchdog if the watchdog device is used. The watchdog +mode has priority over the gpt mode, i.e. if the watchdog is activated, any +gpt api call to this timer will fail with -EBUSY. + +If you add the property + fsl,wdt-on-boot = <n>; +GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. +If n>0, the watchdog is started with a timeout of n seconds. If n=0, the +configuration of the watchdog is not touched. This is useful in two cases: +- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; +- do not touch a configuration assigned by the boot loader which supervises + the boot process itself. + +The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. An mpc5200-gpt can be used as a single line GPIO controller. To do so, add the following properties to the gpt node: @@ -178,3 +193,6 @@ External interrupts: external irq3: interrupts = <1 3 n>; 'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) +fsl,mpc5200-mscan nodes +----------------------- +See file can.txt in this directory. diff --git a/Documentation/powerpc/dts-bindings/fsl/mpic.txt b/Documentation/powerpc/dts-bindings/fsl/mpic.txt new file mode 100644 index 00000000000..71e39cf3215 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/mpic.txt @@ -0,0 +1,42 @@ +* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores + +The OpenPIC specification does not specify which interrupt source has to +become which interrupt number. This is up to the software implementation +of the interrupt controller. The only requirement is that every +interrupt source has to have an unique interrupt number / vector number. +To accomplish this the current implementation assigns the number zero to +the first source, the number one to the second source and so on until +all interrupt sources have their unique number. +Usually the assigned vector number equals the interrupt number mentioned +in the documentation for a given core / CPU. This is however not true +for the e500 cores (MPC85XX CPUs) where the documentation distinguishes +between internal and external interrupt sources and starts counting at +zero for both of them. + +So what to write for external interrupt source X or internal interrupt +source Y into the device tree? Here is an example: + +The memory map for the interrupt controller in the MPC8544[0] shows, +that the first interrupt source starts at 0x5_0000 (PIC Register Address +Map-Interrupt Source Configuration Registers). This source becomes the +number zero therefore: + External interrupt 0 = interrupt number 0 + External interrupt 1 = interrupt number 1 + External interrupt 2 = interrupt number 2 + ... +Every interrupt number allocates 0x20 bytes register space. So to get +its number it is sufficient to shift the lower 16bits to right by five. +So for the external interrupt 10 we have: + 0x0140 >> 5 = 10 + +After the external sources, the internal sources follow. The in core I2C +controller on the MPC8544 for instance has the internal source number +27. Oo obtain its interrupt number we take the lower 16bits of its memory +address (0x5_0560) and shift it right: + 0x0560 >> 5 = 43 + +Therefore the I2C device node for the MPC8544 CPU has to have the +interrupt number 43 specified in the device tree. + +[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual + MPC8544ERM Rev. 1 10/2007 diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt index e7d9a344c4f..80510c018ee 100644 --- a/Documentation/powerpc/dts-bindings/fsl/spi.txt +++ b/Documentation/powerpc/dts-bindings/fsl/spi.txt @@ -13,6 +13,11 @@ Required properties: - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +Optional properties: +- gpios : specifies the gpio pins to be used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + Example: spi@4c0 { cell-index = <0>; @@ -21,4 +26,6 @@ Example: interrupts = <82 0>; interrupt-parent = <700>; mode = "cpu"; + gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> }; diff --git a/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt new file mode 100644 index 00000000000..b558585b1aa --- /dev/null +++ b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt @@ -0,0 +1,109 @@ + +Nintendo GameCube device tree +============================= + +1) The "flipper" node + + This node represents the multi-function "Flipper" chip, which packages + many of the devices found in the Nintendo GameCube. + + Required properties: + + - compatible : Should be "nintendo,flipper" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the interrupt controller within the "Flipper" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - compatible : should be "nintendo,flipper-pic" + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.c.i) The Auxiliary RAM (ARAM) node + + Represents the non cpu-addressable ram designed mainly to store audio + related information. + The ARAM node must be placed under the DSP node. + + Required properties: + + - compatible : should be "nintendo,flipper-aram" + - reg : should contain the ARAM start (zero-based) and length + +1.d) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,flipper-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.g) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + diff --git a/Documentation/powerpc/dts-bindings/nintendo/wii.txt b/Documentation/powerpc/dts-bindings/nintendo/wii.txt new file mode 100644 index 00000000000..a7e155a023b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/nintendo/wii.txt @@ -0,0 +1,184 @@ + +Nintendo Wii device tree +======================== + +0) The root node + + This node represents the Nintendo Wii video game console. + + Required properties: + + - model : Should be "nintendo,wii" + - compatible : Should be "nintendo,wii" + +1) The "hollywood" node + + This node represents the multi-function "Hollywood" chip, which packages + many of the devices found in the Nintendo Wii. + + Required properties: + + - compatible : Should be "nintendo,hollywood" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the "Flipper" interrupt controller within the "Hollywood" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,flipper-pic" + - interrupt-controller + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.d) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + +1.g) The Open Host Controller Interface (OHCI) nodes + + Represent the USB 1.x Open Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" + - reg : should contain the OHCI registers location and length + - interrupts : should contain the OHCI interrupt + +1.h) The Enhanced Host Controller Interface (EHCI) node + + Represents the USB 2.0 Enhanced Host Controller Interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" + - reg : should contain the EHCI registers location and length + - interrupts : should contain the EHCI interrupt + +1.i) The Secure Digital Host Controller Interface (SDHCI) nodes + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-sdhci","sdhci" + - reg : should contain the SDHCI registers location and length + - interrupts : should contain the SDHCI interrupt + +1.j) The Inter-Processsor Communication (IPC) node + + Represent the Inter-Processor Communication interface. This interface + enables communications between the Broadway and the Starlet processors. + + - compatible : should be "nintendo,hollywood-ipc" + - reg : should contain the IPC registers location and length + - interrupts : should contain the IPC interrupt + +1.k) The "Hollywood" interrupt controller node + + Represents the "Hollywood" interrupt controller within the + "Hollywood" chip. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,hollywood-pic" + - reg : should contain the controller registers location and length + - interrupt-controller + - interrupts : should contain the cascade interrupt of the "flipper" pic + - interrupt-parent: should contain the phandle of the "flipper" pic + +1.l) The General Purpose I/O (GPIO) controller node + + Represents the dual access 32 GPIO controller interface. + + Required properties: + + - #gpio-cells : <2> + - compatible : should be "nintendo,hollywood-gpio" + - reg : should contain the IPC registers location and length + - gpio-controller + +1.m) The control node + + Represents the control interface used to setup several miscellaneous + settings of the "Hollywood" chip like boot memory mappings, resets, + disk interface mode, etc. + + Required properties: + + - compatible : should be "nintendo,hollywood-control" + - reg : should contain the control registers location and length + +1.n) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,hollywood-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + diff --git a/Documentation/powerpc/dts-bindings/xilinx.txt b/Documentation/powerpc/dts-bindings/xilinx.txt index 80339fe4300..ea68046bb9c 100644 --- a/Documentation/powerpc/dts-bindings/xilinx.txt +++ b/Documentation/powerpc/dts-bindings/xilinx.txt @@ -292,4 +292,15 @@ - reg-offset : A value of 3 is required - reg-shift : A value of 2 is required + vii) Xilinx USB Host controller + + The Xilinx USB host controller is EHCI compatible but with a different + base address for the EHCI registers, and it is always a big-endian + USB Host controller. The hardware can be configured as high speed only, + or high speed/full speed hybrid. + + Required properties: + - xlnx,support-usb-fs: A value 0 means the core is built as high speed + only. A value 1 means the core also supports + full speed devices. |