6 files changed, 6 insertions, 6 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt
index dc942eaf490..de809e58092 100644
--- a/Documentation/networking/bonding.txt
+++ b/Documentation/networking/bonding.txt
@@ -1023,7 +1023,7 @@ Changing a Bond's Configuration
 files located in /sys/class/net/<bond name>/bonding
 
 	The names of these files correspond directly with the command-
-line parameters described elsewhere in in this file, and, with the
+line parameters described elsewhere in this file, and, with the
 exception of arp_ip_target, they accept the same values.  To see the
 current setting, simply cat the appropriate file.
 
diff --git a/Documentation/networking/cs89x0.txt b/Documentation/networking/cs89x0.txt
index f1f9e8afe1e..64896470e27 100644
--- a/Documentation/networking/cs89x0.txt
+++ b/Documentation/networking/cs89x0.txt
@@ -684,7 +684,7 @@ ethernet@crystal.cirrus.com) and request that you be registered for automatic
 software-update notification.
 
 Cirrus Logic maintains a web page at http://www.cirrus.com with the
-the latest drivers and technical publications.
+latest drivers and technical publications.
 
 
 6.4 Current maintainer
diff --git a/Documentation/networking/decnet.txt b/Documentation/networking/decnet.txt
index e6c39c5831f..badb7480ea6 100644
--- a/Documentation/networking/decnet.txt
+++ b/Documentation/networking/decnet.txt
@@ -82,7 +82,7 @@ ethernet address of your ethernet card has to be set according to the DECnet
 address of the node in order for it to be autoconfigured (and then appear in
 /proc/net/decnet_dev). There is a utility available at the above
 FTP sites called dn2ethaddr which can compute the correct ethernet
-address to use. The address can be set by ifconfig either before at
+address to use. The address can be set by ifconfig either before or
 at the time the device is brought up. If you are using RedHat you can
 add the line:
 
diff --git a/Documentation/networking/e1000.txt b/Documentation/networking/e1000.txt
index 71fe15af356..5c0a5cc0399 100644
--- a/Documentation/networking/e1000.txt
+++ b/Documentation/networking/e1000.txt
@@ -350,7 +350,7 @@ Additional Configurations
 
   As an example, if you install the e1000 driver for two PRO/1000 adapters
   (eth0 and eth1) and set the speed and duplex to 10full and 100half, add
-  the following to modules.conf or or modprobe.conf:
+  the following to modules.conf or modprobe.conf:
 
        alias eth0 e1000
        alias eth1 e1000
diff --git a/Documentation/networking/s2io.txt b/Documentation/networking/s2io.txt
index bd528ffbeb4..4bde53e85f3 100644
--- a/Documentation/networking/s2io.txt
+++ b/Documentation/networking/s2io.txt
@@ -126,7 +126,7 @@ However, you may want to set PCI latency timer to 248.
 #setpci -d 17d5:* LATENCY_TIMER=f8
 For detailed description of the PCI registers, please see Xframe User Guide.
 b. Use 2-buffer mode. This results in large performance boost on
-on certain platforms(eg. SGI Altix, IBM xSeries).
+certain platforms(eg. SGI Altix, IBM xSeries).
 c. Ensure Receive Checksum offload is enabled. Use "ethtool -K ethX" command to 
 set/verify this option.
 d. Enable NAPI feature(in kernel configuration Device Drivers ---> Network 
diff --git a/Documentation/networking/sk98lin.txt b/Documentation/networking/sk98lin.txt
index 82ce5547db4..4e1cc745ec6 100644
--- a/Documentation/networking/sk98lin.txt
+++ b/Documentation/networking/sk98lin.txt
@@ -497,7 +497,7 @@ Solution: In /proc/pci search for the following entry:
           www.syskonnect.com
           
           Some COMPAQ machines have problems dealing with PCI under Linux.
-          Linux. This problem is described in the 'PCI howto' document
+          This problem is described in the 'PCI howto' document
           (included in some distributions or available from the
           web, e.g. at 'www.linux.org').