diff options
-rw-r--r-- | arch/arm/plat-omap/include/plat/nand.h | 7 | ||||
-rw-r--r-- | drivers/mtd/nand/Kconfig | 17 | ||||
-rw-r--r-- | drivers/mtd/nand/omap2.c | 94 |
3 files changed, 41 insertions, 77 deletions
diff --git a/arch/arm/plat-omap/include/plat/nand.h b/arch/arm/plat-omap/include/plat/nand.h index 6562cd082bb..78c0bdb98c1 100644 --- a/arch/arm/plat-omap/include/plat/nand.h +++ b/arch/arm/plat-omap/include/plat/nand.h @@ -10,6 +10,12 @@ #include <linux/mtd/partitions.h> +enum nand_io { + NAND_OMAP_PREFETCH_POLLED = 0, /* prefetch polled mode, default */ + NAND_OMAP_POLLED, /* polled mode, without prefetch */ + NAND_OMAP_PREFETCH_DMA /* prefetch enabled sDMA mode */ +}; + struct omap_nand_platform_data { unsigned int options; int cs; @@ -20,6 +26,7 @@ struct omap_nand_platform_data { int (*nand_setup)(void); int (*dev_ready)(struct omap_nand_platform_data *); int dma_channel; + enum nand_io xfer_type; unsigned long phys_base; int devsize; }; diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index c89592239bc..178e2006063 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -106,23 +106,6 @@ config MTD_NAND_OMAP2 help Support for NAND flash on Texas Instruments OMAP2 and OMAP3 platforms. -config MTD_NAND_OMAP_PREFETCH - bool "GPMC prefetch support for NAND Flash device" - depends on MTD_NAND_OMAP2 - default y - help - The NAND device can be accessed for Read/Write using GPMC PREFETCH engine - to improve the performance. - -config MTD_NAND_OMAP_PREFETCH_DMA - depends on MTD_NAND_OMAP_PREFETCH - bool "DMA mode" - default n - help - The GPMC PREFETCH engine can be configured eigther in MPU interrupt mode - or in DMA interrupt mode. - Say y for DMA mode or MPU mode will be used - config MTD_NAND_IDS tristate diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 7c04cd6fb7a..60bac8e6e9f 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -96,27 +96,6 @@ static const char *part_probes[] = { "cmdlinepart", NULL }; #endif -#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH -static int use_prefetch = 1; - -/* "modprobe ... use_prefetch=0" etc */ -module_param(use_prefetch, bool, 0); -MODULE_PARM_DESC(use_prefetch, "enable/disable use of PREFETCH"); - -#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH_DMA -static int use_dma = 1; - -/* "modprobe ... use_dma=0" etc */ -module_param(use_dma, bool, 0); -MODULE_PARM_DESC(use_dma, "enable/disable use of DMA"); -#else -static const int use_dma; -#endif -#else -const int use_prefetch; -static const int use_dma; -#endif - struct omap_nand_info { struct nand_hw_control controller; struct omap_nand_platform_data *pdata; @@ -324,7 +303,6 @@ static void omap_write_buf_pref(struct mtd_info *mtd, } } -#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH_DMA /* * omap_nand_dma_cb: callback on the completion of dma transfer * @lch: logical channel @@ -426,14 +404,6 @@ out_copy: : omap_write_buf8(mtd, (u_char *) addr, len); return 0; } -#else -static void omap_nand_dma_cb(int lch, u16 ch_status, void *data) {} -static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr, - unsigned int len, int is_write) -{ - return 0; -} -#endif /** * omap_read_buf_dma_pref - read data from NAND controller into buffer @@ -842,28 +812,13 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) info->nand.chip_delay = 50; } - if (use_prefetch) { - + switch (pdata->xfer_type) { + case NAND_OMAP_PREFETCH_POLLED: info->nand.read_buf = omap_read_buf_pref; info->nand.write_buf = omap_write_buf_pref; - if (use_dma) { - err = omap_request_dma(OMAP24XX_DMA_GPMC, "NAND", - omap_nand_dma_cb, &info->comp, &info->dma_ch); - if (err < 0) { - info->dma_ch = -1; - printk(KERN_WARNING "DMA request failed." - " Non-dma data transfer mode\n"); - } else { - omap_set_dma_dest_burst_mode(info->dma_ch, - OMAP_DMA_DATA_BURST_16); - omap_set_dma_src_burst_mode(info->dma_ch, - OMAP_DMA_DATA_BURST_16); - - info->nand.read_buf = omap_read_buf_dma_pref; - info->nand.write_buf = omap_write_buf_dma_pref; - } - } - } else { + break; + + case NAND_OMAP_POLLED: if (info->nand.options & NAND_BUSWIDTH_16) { info->nand.read_buf = omap_read_buf16; info->nand.write_buf = omap_write_buf16; @@ -871,7 +826,33 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) info->nand.read_buf = omap_read_buf8; info->nand.write_buf = omap_write_buf8; } + break; + + case NAND_OMAP_PREFETCH_DMA: + err = omap_request_dma(OMAP24XX_DMA_GPMC, "NAND", + omap_nand_dma_cb, &info->comp, &info->dma_ch); + if (err < 0) { + info->dma_ch = -1; + dev_err(&pdev->dev, "DMA request failed!\n"); + goto out_release_mem_region; + } else { + omap_set_dma_dest_burst_mode(info->dma_ch, + OMAP_DMA_DATA_BURST_16); + omap_set_dma_src_burst_mode(info->dma_ch, + OMAP_DMA_DATA_BURST_16); + + info->nand.read_buf = omap_read_buf_dma_pref; + info->nand.write_buf = omap_write_buf_dma_pref; + } + break; + + default: + dev_err(&pdev->dev, + "xfer_type(%d) not supported!\n", pdata->xfer_type); + err = -EINVAL; + goto out_release_mem_region; } + info->nand.verify_buf = omap_verify_buf; #ifdef CONFIG_MTD_NAND_OMAP_HWECC @@ -897,6 +878,7 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) } } + #ifdef CONFIG_MTD_PARTITIONS err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0); if (err > 0) @@ -926,7 +908,7 @@ static int omap_nand_remove(struct platform_device *pdev) mtd); platform_set_drvdata(pdev, NULL); - if (use_dma) + if (info->dma_ch != -1) omap_free_dma(info->dma_ch); /* Release NAND device, its internal structures and partitions */ @@ -947,16 +929,8 @@ static struct platform_driver omap_nand_driver = { static int __init omap_nand_init(void) { - printk(KERN_INFO "%s driver initializing\n", DRIVER_NAME); + pr_info("%s driver initializing\n", DRIVER_NAME); - /* This check is required if driver is being - * loaded run time as a module - */ - if ((1 == use_dma) && (0 == use_prefetch)) { - printk(KERN_INFO"Wrong parameters: 'use_dma' can not be 1 " - "without use_prefetch'. Prefetch will not be" - " used in either mode (mpu or dma)\n"); - } return platform_driver_register(&omap_nand_driver); } |