[NET]: move config options out to individual protocols

Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.

The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.

Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 74 insertions, 0 deletions

diff --git a/net/atm/Kconfig b/net/atm/Kconfig
new file mode 100644
index 00000000000..bea2426229b
--- /dev/null
+++ b/net/atm/Kconfig
@@ -0,0 +1,74 @@
+#
+# Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)
+#
+
+config ATM
+	tristate "Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	---help---
+	  ATM is a high-speed networking technology for Local Area Networks
+	  and Wide Area Networks.  It uses a fixed packet size and is
+	  connection oriented, allowing for the negotiation of minimum
+	  bandwidth requirements.
+
+	  In order to participate in an ATM network, your Linux box needs an
+	  ATM networking card. If you have that, say Y here and to the driver
+	  of your ATM card below.
+
+	  Note that you need a set of user-space programs to actually make use
+	  of ATM.  See the file <file:Documentation/networking/atm.txt> for
+	  further details.
+
+config ATM_CLIP
+	tristate "Classical IP over ATM (EXPERIMENTAL)"
+	depends on ATM && INET
+	help
+	  Classical IP over ATM for PVCs and SVCs, supporting InARP and
+	  ATMARP. If you want to communication with other IP hosts on your ATM
+	  network, you will typically either say Y here or to "LAN Emulation
+	  (LANE)" below.
+
+config ATM_CLIP_NO_ICMP
+	bool "Do NOT send ICMP if no neighbour (EXPERIMENTAL)"
+	depends on ATM_CLIP
+	help
+	  Normally, an "ICMP host unreachable" message is sent if a neighbour
+	  cannot be reached because there is no VC to it in the kernel's
+	  ATMARP table. This may cause problems when ATMARP table entries are
+	  briefly removed during revalidation. If you say Y here, packets to
+	  such neighbours are silently discarded instead.
+
+config ATM_LANE
+	tristate "LAN Emulation (LANE) support (EXPERIMENTAL)"
+	depends on ATM
+	help
+	  LAN Emulation emulates services of existing LANs across an ATM
+	  network. Besides operating as a normal ATM end station client, Linux
+	  LANE client can also act as an proxy client bridging packets between
+	  ELAN and Ethernet segments. You need LANE if you want to try MPOA.
+
+config ATM_MPOA
+	tristate "Multi-Protocol Over ATM (MPOA) support (EXPERIMENTAL)"
+	depends on ATM && INET && ATM_LANE!=n
+	help
+	  Multi-Protocol Over ATM allows ATM edge devices such as routers,
+	  bridges and ATM attached hosts establish direct ATM VCs across
+	  subnetwork boundaries. These shortcut connections bypass routers
+	  enhancing overall network performance.
+
+config ATM_BR2684
+	tristate "RFC1483/2684 Bridged protocols"
+	depends on ATM && INET
+	help
+	  ATM PVCs can carry ethernet PDUs according to rfc2684 (formerly 1483)
+	  This device will act like an ethernet from the kernels point of view,
+	  with the traffic being carried by ATM PVCs (currently 1 PVC/device).
+	  This is sometimes used over DSL lines.  If in doubt, say N.
+
+config ATM_BR2684_IPFILTER
+	bool "Per-VC IP filter kludge"
+	depends on ATM_BR2684
+	help
+	  This is an experimental mechanism for users who need to terminating a
+	  large number of IP-only vcc's.  Do not enable this unless you are sure
+	  you know what you are doing.