Documentation/: it's -> its where appropriate

Fix obvious cases of "it's" being used when "its" was meant.

Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

3 files changed, 9 insertions, 9 deletions

diff --git a/Documentation/power/regulator/consumer.txt b/Documentation/power/regulator/consumer.txt
index cdebb5145c2..55c4175d809 100644
--- a/Documentation/power/regulator/consumer.txt
+++ b/Documentation/power/regulator/consumer.txt
@@ -8,11 +8,11 @@ Please see overview.txt for a description of the terms used in this text.
 1. Consumer Regulator Access (static & dynamic drivers)
 =======================================================
 
-A consumer driver can get access to it's supply regulator by calling :-
+A consumer driver can get access to its supply regulator by calling :-
 
 regulator = regulator_get(dev, "Vcc");
 
-The consumer passes in it's struct device pointer and power supply ID. The core
+The consumer passes in its struct device pointer and power supply ID. The core
 then finds the correct regulator by consulting a machine specific lookup table.
 If the lookup is successful then this call will return a pointer to the struct
 regulator that supplies this consumer.
@@ -34,7 +34,7 @@ usually be called in your device drivers probe() and remove() respectively.
 2. Regulator Output Enable & Disable (static & dynamic drivers)
 ====================================================================
 
-A consumer can enable it's power supply by calling:-
+A consumer can enable its power supply by calling:-
 
 int regulator_enable(regulator);
 
@@ -49,7 +49,7 @@ int regulator_is_enabled(regulator);
 This will return > zero when the regulator is enabled.
 
 
-A consumer can disable it's supply when no longer needed by calling :-
+A consumer can disable its supply when no longer needed by calling :-
 
 int regulator_disable(regulator);
 
@@ -140,7 +140,7 @@ by calling :-
 int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);
 
 This will cause the core to recalculate the total load on the regulator (based
-on all it's consumers) and change operating mode (if necessary and permitted)
+on all its consumers) and change operating mode (if necessary and permitted)
 to best match the current operating load.
 
 The load_uA value can be determined from the consumers datasheet. e.g.most
diff --git a/Documentation/power/regulator/machine.txt b/Documentation/power/regulator/machine.txt
index 63728fed620..bdec39b9bd7 100644
--- a/Documentation/power/regulator/machine.txt
+++ b/Documentation/power/regulator/machine.txt
@@ -52,7 +52,7 @@ static struct regulator_init_data regulator1_data = {
 };
 
 Regulator-1 supplies power to Regulator-2. This relationship must be registered
-with the core so that Regulator-1 is also enabled when Consumer A enables it's
+with the core so that Regulator-1 is also enabled when Consumer A enables its
 supply (Regulator-2). The supply regulator is set by the supply_regulator_dev
 field below:-
 
diff --git a/Documentation/power/regulator/overview.txt b/Documentation/power/regulator/overview.txt
index ffd185bb605..9363e056188 100644
--- a/Documentation/power/regulator/overview.txt
+++ b/Documentation/power/regulator/overview.txt
@@ -35,16 +35,16 @@ Some terms used in this document:-
   o Consumer     - Electronic device that is supplied power by a regulator.
                    Consumers can be classified into two types:-
 
-                   Static: consumer does not change it's supply voltage or
+                   Static: consumer does not change its supply voltage or
                    current limit. It only needs to enable or disable it's
-                   power supply. It's supply voltage is set by the hardware,
+                   power supply. Its supply voltage is set by the hardware,
                    bootloader, firmware or kernel board initialisation code.
 
                    Dynamic: consumer needs to change it's supply voltage or
                    current limit to meet operation demands.
 
 
-  o Power Domain - Electronic circuit that is supplied it's input power by the
+  o Power Domain - Electronic circuit that is supplied its input power by the
                    output power of a regulator, switch or by another power
                    domain.